142 lines
4.3 KiB
YAML
142 lines
4.3 KiB
YAML
# SPDX-License-Identifier: GPL-2.0
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/iio/adc/adi,ad7606.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: Analog Devices AD7606 Simultaneous Sampling ADC
|
|
|
|
maintainers:
|
|
- Michael Hennerich <michael.hennerich@analog.com>
|
|
|
|
description: |
|
|
Analog Devices AD7606 Simultaneous Sampling ADC
|
|
https://www.analog.com/media/en/technical-documentation/data-sheets/ad7606_7606-6_7606-4.pdf
|
|
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7606B.pdf
|
|
https://www.analog.com/media/en/technical-documentation/data-sheets/AD7616.pdf
|
|
|
|
properties:
|
|
compatible:
|
|
enum:
|
|
- adi,ad7605-4
|
|
- adi,ad7606-8
|
|
- adi,ad7606-6
|
|
- adi,ad7606-4
|
|
- adi,ad7606b
|
|
- adi,ad7616
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
spi-cpha: true
|
|
|
|
spi-cpol: true
|
|
|
|
avcc-supply: true
|
|
|
|
interrupts:
|
|
maxItems: 1
|
|
|
|
adi,conversion-start-gpios:
|
|
description:
|
|
Must be the device tree identifier of the CONVST pin.
|
|
This logic input is used to initiate conversions on the analog
|
|
input channels. As the line is active high, it should be marked
|
|
GPIO_ACTIVE_HIGH.
|
|
maxItems: 1
|
|
|
|
reset-gpios:
|
|
description:
|
|
Must be the device tree identifier of the RESET pin. If specified,
|
|
it will be asserted during driver probe. As the line is active high,
|
|
it should be marked GPIO_ACTIVE_HIGH.
|
|
maxItems: 1
|
|
|
|
standby-gpios:
|
|
description:
|
|
Must be the device tree identifier of the STBY pin. This pin is used
|
|
to place the AD7606 into one of two power-down modes, Standby mode or
|
|
Shutdown mode. As the line is active low, it should be marked
|
|
GPIO_ACTIVE_LOW.
|
|
maxItems: 1
|
|
|
|
adi,first-data-gpios:
|
|
description:
|
|
Must be the device tree identifier of the FRSTDATA pin.
|
|
The FRSTDATA output indicates when the first channel, V1, is
|
|
being read back on either the parallel, byte or serial interface.
|
|
As the line is active high, it should be marked GPIO_ACTIVE_HIGH.
|
|
maxItems: 1
|
|
|
|
adi,range-gpios:
|
|
description:
|
|
Must be the device tree identifier of the RANGE pin. The polarity on
|
|
this pin determines the input range of the analog input channels. If
|
|
this pin is tied to a logic high, the analog input range is ±10V for
|
|
all channels. If this pin is tied to a logic low, the analog input range
|
|
is ±5V for all channels. As the line is active high, it should be marked
|
|
GPIO_ACTIVE_HIGH.
|
|
maxItems: 1
|
|
|
|
adi,oversampling-ratio-gpios:
|
|
description:
|
|
Must be the device tree identifier of the over-sampling
|
|
mode pins. As the line is active high, it should be marked
|
|
GPIO_ACTIVE_HIGH.
|
|
maxItems: 3
|
|
|
|
adi,sw-mode:
|
|
description:
|
|
Software mode of operation, so far available only for ad7616 and ad7606b.
|
|
It is enabled when all three oversampling mode pins are connected to
|
|
high level. The device is configured by the corresponding registers. If the
|
|
adi,oversampling-ratio-gpios property is defined, then the driver will set the
|
|
oversampling gpios to high. Otherwise, it is assumed that the pins are hardwired
|
|
to VDD.
|
|
type: boolean
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- spi-cpha
|
|
- avcc-supply
|
|
- interrupts
|
|
- adi,conversion-start-gpios
|
|
|
|
allOf:
|
|
- $ref: /schemas/spi/spi-peripheral-props.yaml#
|
|
|
|
unevaluatedProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
spi0 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
adc@0 {
|
|
compatible = "adi,ad7606-8";
|
|
reg = <0>;
|
|
spi-max-frequency = <1000000>;
|
|
spi-cpol;
|
|
spi-cpha;
|
|
|
|
avcc-supply = <&adc_vref>;
|
|
|
|
interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
|
|
interrupt-parent = <&gpio>;
|
|
|
|
adi,conversion-start-gpios = <&gpio 17 GPIO_ACTIVE_HIGH>;
|
|
reset-gpios = <&gpio 27 GPIO_ACTIVE_HIGH>;
|
|
adi,first-data-gpios = <&gpio 22 GPIO_ACTIVE_HIGH>;
|
|
adi,oversampling-ratio-gpios = <&gpio 18 GPIO_ACTIVE_HIGH>,
|
|
<&gpio 23 GPIO_ACTIVE_HIGH>,
|
|
<&gpio 26 GPIO_ACTIVE_HIGH>;
|
|
standby-gpios = <&gpio 24 GPIO_ACTIVE_LOW>;
|
|
adi,sw-mode;
|
|
};
|
|
};
|
|
...
|