643 lines
14 KiB
C
643 lines
14 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* TPO TD043MTEA1 Panel driver
|
|
*
|
|
* Author: Gražvydas Ignotas <notasas@gmail.com>
|
|
* Converted to new DSS device model: Tomi Valkeinen <tomi.valkeinen@ti.com>
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/spi/spi.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/err.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/of_gpio.h>
|
|
|
|
#include <video/omapfb_dss.h>
|
|
|
|
#define TPO_R02_MODE(x) ((x) & 7)
|
|
#define TPO_R02_MODE_800x480 7
|
|
#define TPO_R02_NCLK_RISING BIT(3)
|
|
#define TPO_R02_HSYNC_HIGH BIT(4)
|
|
#define TPO_R02_VSYNC_HIGH BIT(5)
|
|
|
|
#define TPO_R03_NSTANDBY BIT(0)
|
|
#define TPO_R03_EN_CP_CLK BIT(1)
|
|
#define TPO_R03_EN_VGL_PUMP BIT(2)
|
|
#define TPO_R03_EN_PWM BIT(3)
|
|
#define TPO_R03_DRIVING_CAP_100 BIT(4)
|
|
#define TPO_R03_EN_PRE_CHARGE BIT(6)
|
|
#define TPO_R03_SOFTWARE_CTL BIT(7)
|
|
|
|
#define TPO_R04_NFLIP_H BIT(0)
|
|
#define TPO_R04_NFLIP_V BIT(1)
|
|
#define TPO_R04_CP_CLK_FREQ_1H BIT(2)
|
|
#define TPO_R04_VGL_FREQ_1H BIT(4)
|
|
|
|
#define TPO_R03_VAL_NORMAL (TPO_R03_NSTANDBY | TPO_R03_EN_CP_CLK | \
|
|
TPO_R03_EN_VGL_PUMP | TPO_R03_EN_PWM | \
|
|
TPO_R03_DRIVING_CAP_100 | TPO_R03_EN_PRE_CHARGE | \
|
|
TPO_R03_SOFTWARE_CTL)
|
|
|
|
#define TPO_R03_VAL_STANDBY (TPO_R03_DRIVING_CAP_100 | \
|
|
TPO_R03_EN_PRE_CHARGE | TPO_R03_SOFTWARE_CTL)
|
|
|
|
static const u16 tpo_td043_def_gamma[12] = {
|
|
105, 315, 381, 431, 490, 537, 579, 686, 780, 837, 880, 1023
|
|
};
|
|
|
|
struct panel_drv_data {
|
|
struct omap_dss_device dssdev;
|
|
struct omap_dss_device *in;
|
|
|
|
struct omap_video_timings videomode;
|
|
|
|
int data_lines;
|
|
|
|
struct spi_device *spi;
|
|
struct regulator *vcc_reg;
|
|
int nreset_gpio;
|
|
u16 gamma[12];
|
|
u32 mode;
|
|
u32 hmirror:1;
|
|
u32 vmirror:1;
|
|
u32 powered_on:1;
|
|
u32 spi_suspended:1;
|
|
u32 power_on_resume:1;
|
|
};
|
|
|
|
static const struct omap_video_timings tpo_td043_timings = {
|
|
.x_res = 800,
|
|
.y_res = 480,
|
|
|
|
.pixelclock = 36000000,
|
|
|
|
.hsw = 1,
|
|
.hfp = 68,
|
|
.hbp = 214,
|
|
|
|
.vsw = 1,
|
|
.vfp = 39,
|
|
.vbp = 34,
|
|
|
|
.vsync_level = OMAPDSS_SIG_ACTIVE_LOW,
|
|
.hsync_level = OMAPDSS_SIG_ACTIVE_LOW,
|
|
.data_pclk_edge = OMAPDSS_DRIVE_SIG_FALLING_EDGE,
|
|
.de_level = OMAPDSS_SIG_ACTIVE_HIGH,
|
|
.sync_pclk_edge = OMAPDSS_DRIVE_SIG_RISING_EDGE,
|
|
};
|
|
|
|
#define to_panel_data(p) container_of(p, struct panel_drv_data, dssdev)
|
|
|
|
static int tpo_td043_write(struct spi_device *spi, u8 addr, u8 data)
|
|
{
|
|
struct spi_message m;
|
|
struct spi_transfer xfer;
|
|
u16 w;
|
|
int r;
|
|
|
|
spi_message_init(&m);
|
|
|
|
memset(&xfer, 0, sizeof(xfer));
|
|
|
|
w = ((u16)addr << 10) | (1 << 8) | data;
|
|
xfer.tx_buf = &w;
|
|
xfer.bits_per_word = 16;
|
|
xfer.len = 2;
|
|
spi_message_add_tail(&xfer, &m);
|
|
|
|
r = spi_sync(spi, &m);
|
|
if (r < 0)
|
|
dev_warn(&spi->dev, "failed to write to LCD reg (%d)\n", r);
|
|
return r;
|
|
}
|
|
|
|
static void tpo_td043_write_gamma(struct spi_device *spi, u16 gamma[12])
|
|
{
|
|
u8 i, val;
|
|
|
|
/* gamma bits [9:8] */
|
|
for (val = i = 0; i < 4; i++)
|
|
val |= (gamma[i] & 0x300) >> ((i + 1) * 2);
|
|
tpo_td043_write(spi, 0x11, val);
|
|
|
|
for (val = i = 0; i < 4; i++)
|
|
val |= (gamma[i+4] & 0x300) >> ((i + 1) * 2);
|
|
tpo_td043_write(spi, 0x12, val);
|
|
|
|
for (val = i = 0; i < 4; i++)
|
|
val |= (gamma[i+8] & 0x300) >> ((i + 1) * 2);
|
|
tpo_td043_write(spi, 0x13, val);
|
|
|
|
/* gamma bits [7:0] */
|
|
for (val = i = 0; i < 12; i++)
|
|
tpo_td043_write(spi, 0x14 + i, gamma[i] & 0xff);
|
|
}
|
|
|
|
static int tpo_td043_write_mirror(struct spi_device *spi, bool h, bool v)
|
|
{
|
|
u8 reg4 = TPO_R04_NFLIP_H | TPO_R04_NFLIP_V |
|
|
TPO_R04_CP_CLK_FREQ_1H | TPO_R04_VGL_FREQ_1H;
|
|
if (h)
|
|
reg4 &= ~TPO_R04_NFLIP_H;
|
|
if (v)
|
|
reg4 &= ~TPO_R04_NFLIP_V;
|
|
|
|
return tpo_td043_write(spi, 4, reg4);
|
|
}
|
|
|
|
static int tpo_td043_set_hmirror(struct omap_dss_device *dssdev, bool enable)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dssdev->dev);
|
|
|
|
ddata->hmirror = enable;
|
|
return tpo_td043_write_mirror(ddata->spi, ddata->hmirror,
|
|
ddata->vmirror);
|
|
}
|
|
|
|
static bool tpo_td043_get_hmirror(struct omap_dss_device *dssdev)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dssdev->dev);
|
|
|
|
return ddata->hmirror;
|
|
}
|
|
|
|
static ssize_t tpo_td043_vmirror_show(struct device *dev,
|
|
struct device_attribute *attr, char *buf)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dev);
|
|
|
|
return sysfs_emit(buf, "%d\n", ddata->vmirror);
|
|
}
|
|
|
|
static ssize_t tpo_td043_vmirror_store(struct device *dev,
|
|
struct device_attribute *attr, const char *buf, size_t count)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dev);
|
|
int val;
|
|
int ret;
|
|
|
|
ret = kstrtoint(buf, 0, &val);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
val = !!val;
|
|
|
|
ret = tpo_td043_write_mirror(ddata->spi, ddata->hmirror, val);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
ddata->vmirror = val;
|
|
|
|
return count;
|
|
}
|
|
|
|
static ssize_t tpo_td043_mode_show(struct device *dev,
|
|
struct device_attribute *attr, char *buf)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dev);
|
|
|
|
return sysfs_emit(buf, "%d\n", ddata->mode);
|
|
}
|
|
|
|
static ssize_t tpo_td043_mode_store(struct device *dev,
|
|
struct device_attribute *attr, const char *buf, size_t count)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dev);
|
|
long val;
|
|
int ret;
|
|
|
|
ret = kstrtol(buf, 0, &val);
|
|
if (ret != 0 || val & ~7)
|
|
return -EINVAL;
|
|
|
|
ddata->mode = val;
|
|
|
|
val |= TPO_R02_NCLK_RISING;
|
|
tpo_td043_write(ddata->spi, 2, val);
|
|
|
|
return count;
|
|
}
|
|
|
|
static ssize_t tpo_td043_gamma_show(struct device *dev,
|
|
struct device_attribute *attr, char *buf)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dev);
|
|
ssize_t len = 0;
|
|
int ret;
|
|
int i;
|
|
|
|
for (i = 0; i < ARRAY_SIZE(ddata->gamma); i++) {
|
|
ret = snprintf(buf + len, PAGE_SIZE - len, "%u ",
|
|
ddata->gamma[i]);
|
|
if (ret < 0)
|
|
return ret;
|
|
len += ret;
|
|
}
|
|
buf[len - 1] = '\n';
|
|
|
|
return len;
|
|
}
|
|
|
|
static ssize_t tpo_td043_gamma_store(struct device *dev,
|
|
struct device_attribute *attr, const char *buf, size_t count)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dev);
|
|
unsigned int g[12];
|
|
int ret;
|
|
int i;
|
|
|
|
ret = sscanf(buf, "%u %u %u %u %u %u %u %u %u %u %u %u",
|
|
&g[0], &g[1], &g[2], &g[3], &g[4], &g[5],
|
|
&g[6], &g[7], &g[8], &g[9], &g[10], &g[11]);
|
|
|
|
if (ret != 12)
|
|
return -EINVAL;
|
|
|
|
for (i = 0; i < 12; i++)
|
|
ddata->gamma[i] = g[i];
|
|
|
|
tpo_td043_write_gamma(ddata->spi, ddata->gamma);
|
|
|
|
return count;
|
|
}
|
|
|
|
static DEVICE_ATTR(vmirror, S_IRUGO | S_IWUSR,
|
|
tpo_td043_vmirror_show, tpo_td043_vmirror_store);
|
|
static DEVICE_ATTR(mode, S_IRUGO | S_IWUSR,
|
|
tpo_td043_mode_show, tpo_td043_mode_store);
|
|
static DEVICE_ATTR(gamma, S_IRUGO | S_IWUSR,
|
|
tpo_td043_gamma_show, tpo_td043_gamma_store);
|
|
|
|
static struct attribute *tpo_td043_attrs[] = {
|
|
&dev_attr_vmirror.attr,
|
|
&dev_attr_mode.attr,
|
|
&dev_attr_gamma.attr,
|
|
NULL,
|
|
};
|
|
|
|
static const struct attribute_group tpo_td043_attr_group = {
|
|
.attrs = tpo_td043_attrs,
|
|
};
|
|
|
|
static int tpo_td043_power_on(struct panel_drv_data *ddata)
|
|
{
|
|
int r;
|
|
|
|
if (ddata->powered_on)
|
|
return 0;
|
|
|
|
r = regulator_enable(ddata->vcc_reg);
|
|
if (r != 0)
|
|
return r;
|
|
|
|
/* wait for panel to stabilize */
|
|
msleep(160);
|
|
|
|
if (gpio_is_valid(ddata->nreset_gpio))
|
|
gpio_set_value(ddata->nreset_gpio, 1);
|
|
|
|
tpo_td043_write(ddata->spi, 2,
|
|
TPO_R02_MODE(ddata->mode) | TPO_R02_NCLK_RISING);
|
|
tpo_td043_write(ddata->spi, 3, TPO_R03_VAL_NORMAL);
|
|
tpo_td043_write(ddata->spi, 0x20, 0xf0);
|
|
tpo_td043_write(ddata->spi, 0x21, 0xf0);
|
|
tpo_td043_write_mirror(ddata->spi, ddata->hmirror,
|
|
ddata->vmirror);
|
|
tpo_td043_write_gamma(ddata->spi, ddata->gamma);
|
|
|
|
ddata->powered_on = 1;
|
|
return 0;
|
|
}
|
|
|
|
static void tpo_td043_power_off(struct panel_drv_data *ddata)
|
|
{
|
|
if (!ddata->powered_on)
|
|
return;
|
|
|
|
tpo_td043_write(ddata->spi, 3,
|
|
TPO_R03_VAL_STANDBY | TPO_R03_EN_PWM);
|
|
|
|
if (gpio_is_valid(ddata->nreset_gpio))
|
|
gpio_set_value(ddata->nreset_gpio, 0);
|
|
|
|
/* wait for at least 2 vsyncs before cutting off power */
|
|
msleep(50);
|
|
|
|
tpo_td043_write(ddata->spi, 3, TPO_R03_VAL_STANDBY);
|
|
|
|
regulator_disable(ddata->vcc_reg);
|
|
|
|
ddata->powered_on = 0;
|
|
}
|
|
|
|
static int tpo_td043_connect(struct omap_dss_device *dssdev)
|
|
{
|
|
struct panel_drv_data *ddata = to_panel_data(dssdev);
|
|
struct omap_dss_device *in = ddata->in;
|
|
|
|
if (omapdss_device_is_connected(dssdev))
|
|
return 0;
|
|
|
|
return in->ops.dpi->connect(in, dssdev);
|
|
}
|
|
|
|
static void tpo_td043_disconnect(struct omap_dss_device *dssdev)
|
|
{
|
|
struct panel_drv_data *ddata = to_panel_data(dssdev);
|
|
struct omap_dss_device *in = ddata->in;
|
|
|
|
if (!omapdss_device_is_connected(dssdev))
|
|
return;
|
|
|
|
in->ops.dpi->disconnect(in, dssdev);
|
|
}
|
|
|
|
static int tpo_td043_enable(struct omap_dss_device *dssdev)
|
|
{
|
|
struct panel_drv_data *ddata = to_panel_data(dssdev);
|
|
struct omap_dss_device *in = ddata->in;
|
|
int r;
|
|
|
|
if (!omapdss_device_is_connected(dssdev))
|
|
return -ENODEV;
|
|
|
|
if (omapdss_device_is_enabled(dssdev))
|
|
return 0;
|
|
|
|
if (ddata->data_lines)
|
|
in->ops.dpi->set_data_lines(in, ddata->data_lines);
|
|
in->ops.dpi->set_timings(in, &ddata->videomode);
|
|
|
|
r = in->ops.dpi->enable(in);
|
|
if (r)
|
|
return r;
|
|
|
|
/*
|
|
* If we are resuming from system suspend, SPI clocks might not be
|
|
* enabled yet, so we'll program the LCD from SPI PM resume callback.
|
|
*/
|
|
if (!ddata->spi_suspended) {
|
|
r = tpo_td043_power_on(ddata);
|
|
if (r) {
|
|
in->ops.dpi->disable(in);
|
|
return r;
|
|
}
|
|
}
|
|
|
|
dssdev->state = OMAP_DSS_DISPLAY_ACTIVE;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void tpo_td043_disable(struct omap_dss_device *dssdev)
|
|
{
|
|
struct panel_drv_data *ddata = to_panel_data(dssdev);
|
|
struct omap_dss_device *in = ddata->in;
|
|
|
|
if (!omapdss_device_is_enabled(dssdev))
|
|
return;
|
|
|
|
in->ops.dpi->disable(in);
|
|
|
|
if (!ddata->spi_suspended)
|
|
tpo_td043_power_off(ddata);
|
|
|
|
dssdev->state = OMAP_DSS_DISPLAY_DISABLED;
|
|
}
|
|
|
|
static void tpo_td043_set_timings(struct omap_dss_device *dssdev,
|
|
struct omap_video_timings *timings)
|
|
{
|
|
struct panel_drv_data *ddata = to_panel_data(dssdev);
|
|
struct omap_dss_device *in = ddata->in;
|
|
|
|
ddata->videomode = *timings;
|
|
dssdev->panel.timings = *timings;
|
|
|
|
in->ops.dpi->set_timings(in, timings);
|
|
}
|
|
|
|
static void tpo_td043_get_timings(struct omap_dss_device *dssdev,
|
|
struct omap_video_timings *timings)
|
|
{
|
|
struct panel_drv_data *ddata = to_panel_data(dssdev);
|
|
|
|
*timings = ddata->videomode;
|
|
}
|
|
|
|
static int tpo_td043_check_timings(struct omap_dss_device *dssdev,
|
|
struct omap_video_timings *timings)
|
|
{
|
|
struct panel_drv_data *ddata = to_panel_data(dssdev);
|
|
struct omap_dss_device *in = ddata->in;
|
|
|
|
return in->ops.dpi->check_timings(in, timings);
|
|
}
|
|
|
|
static struct omap_dss_driver tpo_td043_ops = {
|
|
.connect = tpo_td043_connect,
|
|
.disconnect = tpo_td043_disconnect,
|
|
|
|
.enable = tpo_td043_enable,
|
|
.disable = tpo_td043_disable,
|
|
|
|
.set_timings = tpo_td043_set_timings,
|
|
.get_timings = tpo_td043_get_timings,
|
|
.check_timings = tpo_td043_check_timings,
|
|
|
|
.set_mirror = tpo_td043_set_hmirror,
|
|
.get_mirror = tpo_td043_get_hmirror,
|
|
|
|
.get_resolution = omapdss_default_get_resolution,
|
|
};
|
|
|
|
|
|
static int tpo_td043_probe_of(struct spi_device *spi)
|
|
{
|
|
struct device_node *node = spi->dev.of_node;
|
|
struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev);
|
|
struct omap_dss_device *in;
|
|
int gpio;
|
|
|
|
gpio = of_get_named_gpio(node, "reset-gpios", 0);
|
|
if (!gpio_is_valid(gpio)) {
|
|
dev_err(&spi->dev, "failed to parse enable gpio\n");
|
|
return gpio;
|
|
}
|
|
ddata->nreset_gpio = gpio;
|
|
|
|
in = omapdss_of_find_source_for_first_ep(node);
|
|
if (IS_ERR(in)) {
|
|
dev_err(&spi->dev, "failed to find video source\n");
|
|
return PTR_ERR(in);
|
|
}
|
|
|
|
ddata->in = in;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tpo_td043_probe(struct spi_device *spi)
|
|
{
|
|
struct panel_drv_data *ddata;
|
|
struct omap_dss_device *dssdev;
|
|
int r;
|
|
|
|
dev_dbg(&spi->dev, "%s\n", __func__);
|
|
|
|
if (!spi->dev.of_node)
|
|
return -ENODEV;
|
|
|
|
spi->bits_per_word = 16;
|
|
spi->mode = SPI_MODE_0;
|
|
|
|
r = spi_setup(spi);
|
|
if (r < 0) {
|
|
dev_err(&spi->dev, "spi_setup failed: %d\n", r);
|
|
return r;
|
|
}
|
|
|
|
ddata = devm_kzalloc(&spi->dev, sizeof(*ddata), GFP_KERNEL);
|
|
if (ddata == NULL)
|
|
return -ENOMEM;
|
|
|
|
dev_set_drvdata(&spi->dev, ddata);
|
|
|
|
ddata->spi = spi;
|
|
|
|
r = tpo_td043_probe_of(spi);
|
|
if (r)
|
|
return r;
|
|
|
|
ddata->mode = TPO_R02_MODE_800x480;
|
|
memcpy(ddata->gamma, tpo_td043_def_gamma, sizeof(ddata->gamma));
|
|
|
|
ddata->vcc_reg = devm_regulator_get(&spi->dev, "vcc");
|
|
if (IS_ERR(ddata->vcc_reg)) {
|
|
r = dev_err_probe(&spi->dev, r, "failed to get LCD VCC regulator\n");
|
|
goto err_regulator;
|
|
}
|
|
|
|
if (gpio_is_valid(ddata->nreset_gpio)) {
|
|
r = devm_gpio_request_one(&spi->dev,
|
|
ddata->nreset_gpio, GPIOF_OUT_INIT_LOW,
|
|
"lcd reset");
|
|
if (r < 0) {
|
|
dev_err(&spi->dev, "couldn't request reset GPIO\n");
|
|
goto err_gpio_req;
|
|
}
|
|
}
|
|
|
|
r = sysfs_create_group(&spi->dev.kobj, &tpo_td043_attr_group);
|
|
if (r) {
|
|
dev_err(&spi->dev, "failed to create sysfs files\n");
|
|
goto err_sysfs;
|
|
}
|
|
|
|
ddata->videomode = tpo_td043_timings;
|
|
|
|
dssdev = &ddata->dssdev;
|
|
dssdev->dev = &spi->dev;
|
|
dssdev->driver = &tpo_td043_ops;
|
|
dssdev->type = OMAP_DISPLAY_TYPE_DPI;
|
|
dssdev->owner = THIS_MODULE;
|
|
dssdev->panel.timings = ddata->videomode;
|
|
|
|
r = omapdss_register_display(dssdev);
|
|
if (r) {
|
|
dev_err(&spi->dev, "Failed to register panel\n");
|
|
goto err_reg;
|
|
}
|
|
|
|
return 0;
|
|
|
|
err_reg:
|
|
sysfs_remove_group(&spi->dev.kobj, &tpo_td043_attr_group);
|
|
err_sysfs:
|
|
err_gpio_req:
|
|
err_regulator:
|
|
omap_dss_put_device(ddata->in);
|
|
return r;
|
|
}
|
|
|
|
static void tpo_td043_remove(struct spi_device *spi)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(&spi->dev);
|
|
struct omap_dss_device *dssdev = &ddata->dssdev;
|
|
struct omap_dss_device *in = ddata->in;
|
|
|
|
dev_dbg(&ddata->spi->dev, "%s\n", __func__);
|
|
|
|
omapdss_unregister_display(dssdev);
|
|
|
|
tpo_td043_disable(dssdev);
|
|
tpo_td043_disconnect(dssdev);
|
|
|
|
omap_dss_put_device(in);
|
|
|
|
sysfs_remove_group(&spi->dev.kobj, &tpo_td043_attr_group);
|
|
}
|
|
|
|
#ifdef CONFIG_PM_SLEEP
|
|
static int tpo_td043_spi_suspend(struct device *dev)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dev);
|
|
|
|
dev_dbg(dev, "tpo_td043_spi_suspend, tpo %p\n", ddata);
|
|
|
|
ddata->power_on_resume = ddata->powered_on;
|
|
tpo_td043_power_off(ddata);
|
|
ddata->spi_suspended = 1;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int tpo_td043_spi_resume(struct device *dev)
|
|
{
|
|
struct panel_drv_data *ddata = dev_get_drvdata(dev);
|
|
int ret;
|
|
|
|
dev_dbg(dev, "tpo_td043_spi_resume\n");
|
|
|
|
if (ddata->power_on_resume) {
|
|
ret = tpo_td043_power_on(ddata);
|
|
if (ret)
|
|
return ret;
|
|
}
|
|
ddata->spi_suspended = 0;
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static SIMPLE_DEV_PM_OPS(tpo_td043_spi_pm,
|
|
tpo_td043_spi_suspend, tpo_td043_spi_resume);
|
|
|
|
static const struct of_device_id tpo_td043_of_match[] = {
|
|
{ .compatible = "omapdss,tpo,td043mtea1", },
|
|
{},
|
|
};
|
|
|
|
MODULE_DEVICE_TABLE(of, tpo_td043_of_match);
|
|
|
|
static struct spi_driver tpo_td043_spi_driver = {
|
|
.driver = {
|
|
.name = "panel-tpo-td043mtea1",
|
|
.pm = &tpo_td043_spi_pm,
|
|
.of_match_table = tpo_td043_of_match,
|
|
.suppress_bind_attrs = true,
|
|
},
|
|
.probe = tpo_td043_probe,
|
|
.remove = tpo_td043_remove,
|
|
};
|
|
|
|
module_spi_driver(tpo_td043_spi_driver);
|
|
|
|
MODULE_ALIAS("spi:tpo,td043mtea1");
|
|
MODULE_AUTHOR("Gražvydas Ignotas <notasas@gmail.com>");
|
|
MODULE_DESCRIPTION("TPO TD043MTEA1 LCD Driver");
|
|
MODULE_LICENSE("GPL");
|