770 lines
14 KiB
Plaintext
770 lines
14 KiB
Plaintext
// SPDX-License-Identifier: BSD-3-Clause
|
|
/*
|
|
* SC7180 IDP board device tree source
|
|
*
|
|
* Copyright (c) 2019, The Linux Foundation. All rights reserved.
|
|
*/
|
|
|
|
/dts-v1/;
|
|
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
|
|
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
|
|
#include "sc7180.dtsi"
|
|
#include "pm6150.dtsi"
|
|
#include "pm6150l.dtsi"
|
|
|
|
/ {
|
|
model = "Qualcomm Technologies, Inc. SC7180 IDP";
|
|
compatible = "qcom,sc7180-idp", "qcom,sc7180";
|
|
|
|
aliases {
|
|
bluetooth0 = &bluetooth;
|
|
hsuart0 = &uart3;
|
|
serial0 = &uart8;
|
|
wifi0 = &wifi;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = "serial0:115200n8";
|
|
};
|
|
};
|
|
|
|
/*
|
|
* Reserved memory changes
|
|
*
|
|
* Delete all unused memory nodes and define the peripheral memory regions
|
|
* required by the board dts.
|
|
*
|
|
*/
|
|
|
|
/delete-node/ &hyp_mem;
|
|
/delete-node/ &xbl_mem;
|
|
/delete-node/ &aop_mem;
|
|
/delete-node/ &sec_apps_mem;
|
|
/delete-node/ &tz_mem;
|
|
|
|
/* Increase the size from 2MB to 8MB */
|
|
&rmtfs_mem {
|
|
reg = <0x0 0x94600000 0x0 0x800000>;
|
|
};
|
|
|
|
/ {
|
|
reserved-memory {
|
|
atf_mem: memory@80b00000 {
|
|
reg = <0x0 0x80b00000 0x0 0x100000>;
|
|
no-map;
|
|
};
|
|
|
|
mpss_mem: memory@86000000 {
|
|
reg = <0x0 0x86000000 0x0 0x8c00000>;
|
|
no-map;
|
|
};
|
|
|
|
camera_mem: memory@8ec00000 {
|
|
reg = <0x0 0x8ec00000 0x0 0x500000>;
|
|
no-map;
|
|
};
|
|
|
|
venus_mem: memory@8f600000 {
|
|
reg = <0 0x8f600000 0 0x500000>;
|
|
no-map;
|
|
};
|
|
|
|
wlan_mem: memory@94100000 {
|
|
reg = <0x0 0x94100000 0x0 0x200000>;
|
|
no-map;
|
|
};
|
|
|
|
mba_mem: memory@94400000 {
|
|
reg = <0x0 0x94400000 0x0 0x200000>;
|
|
no-map;
|
|
};
|
|
};
|
|
};
|
|
|
|
&apps_rsc {
|
|
pm6150-rpmh-regulators {
|
|
compatible = "qcom,pm6150-rpmh-regulators";
|
|
qcom,pmic-id = "a";
|
|
|
|
vreg_s1a_1p1: smps1 {
|
|
regulator-min-microvolt = <1128000>;
|
|
regulator-max-microvolt = <1128000>;
|
|
};
|
|
|
|
vreg_s4a_1p0: smps4 {
|
|
regulator-min-microvolt = <824000>;
|
|
regulator-max-microvolt = <1120000>;
|
|
};
|
|
|
|
vreg_s5a_2p0: smps5 {
|
|
regulator-min-microvolt = <1744000>;
|
|
regulator-max-microvolt = <2040000>;
|
|
};
|
|
|
|
vreg_l1a_1p2: ldo1 {
|
|
regulator-min-microvolt = <1178000>;
|
|
regulator-max-microvolt = <1256000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l2a_1p0: ldo2 {
|
|
regulator-min-microvolt = <944000>;
|
|
regulator-max-microvolt = <1056000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l3a_1p0: ldo3 {
|
|
regulator-min-microvolt = <968000>;
|
|
regulator-max-microvolt = <1064000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l4a_0p8: ldo4 {
|
|
regulator-min-microvolt = <824000>;
|
|
regulator-max-microvolt = <928000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l5a_2p7: ldo5 {
|
|
regulator-min-microvolt = <2496000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l6a_0p6: ldo6 {
|
|
regulator-min-microvolt = <568000>;
|
|
regulator-max-microvolt = <648000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l9a_0p6: ldo9 {
|
|
regulator-min-microvolt = <488000>;
|
|
regulator-max-microvolt = <800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l10a_1p8: ldo10 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1832000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l11a_1p8: ldo11 {
|
|
regulator-min-microvolt = <1696000>;
|
|
regulator-max-microvolt = <1904000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l12a_1p8: ldo12 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l13a_1p8: ldo13 {
|
|
regulator-min-microvolt = <1696000>;
|
|
regulator-max-microvolt = <1904000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l14a_1p8: ldo14 {
|
|
regulator-min-microvolt = <1728000>;
|
|
regulator-max-microvolt = <1832000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l15a_1p8: ldo15 {
|
|
regulator-min-microvolt = <1696000>;
|
|
regulator-max-microvolt = <1904000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l16a_2p7: ldo16 {
|
|
regulator-min-microvolt = <2496000>;
|
|
regulator-max-microvolt = <3304000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l17a_3p0: ldo17 {
|
|
regulator-min-microvolt = <2920000>;
|
|
regulator-max-microvolt = <3232000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l18a_2p8: ldo18 {
|
|
regulator-min-microvolt = <2496000>;
|
|
regulator-max-microvolt = <3304000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l19a_2p9: ldo19 {
|
|
regulator-min-microvolt = <2960000>;
|
|
regulator-max-microvolt = <2960000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
};
|
|
|
|
pm6150l-rpmh-regulators {
|
|
compatible = "qcom,pm6150l-rpmh-regulators";
|
|
qcom,pmic-id = "c";
|
|
|
|
vreg_s8c_1p3: smps8 {
|
|
regulator-min-microvolt = <1120000>;
|
|
regulator-max-microvolt = <1408000>;
|
|
};
|
|
|
|
vreg_l1c_1p8: ldo1 {
|
|
regulator-min-microvolt = <1616000>;
|
|
regulator-max-microvolt = <1984000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l2c_1p3: ldo2 {
|
|
regulator-min-microvolt = <1168000>;
|
|
regulator-max-microvolt = <1304000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l3c_1p2: ldo3 {
|
|
regulator-min-microvolt = <1144000>;
|
|
regulator-max-microvolt = <1304000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l4c_1p8: ldo4 {
|
|
regulator-min-microvolt = <1648000>;
|
|
regulator-max-microvolt = <3304000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l5c_1p8: ldo5 {
|
|
regulator-min-microvolt = <1648000>;
|
|
regulator-max-microvolt = <3304000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l6c_2p9: ldo6 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <2950000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l7c_3p0: ldo7 {
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3312000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l8c_1p8: ldo8 {
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1904000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l9c_2p9: ldo9 {
|
|
regulator-min-microvolt = <2960000>;
|
|
regulator-max-microvolt = <2960000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
|
|
};
|
|
|
|
vreg_l10c_3p3: ldo10 {
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3400000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_l11c_3p3: ldo11 {
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3400000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_LPM>;
|
|
};
|
|
|
|
vreg_bob: bob {
|
|
regulator-min-microvolt = <3008000>;
|
|
regulator-max-microvolt = <3960000>;
|
|
regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&dsi0 {
|
|
status = "okay";
|
|
|
|
vdda-supply = <&vreg_l3c_1p2>;
|
|
|
|
panel@0 {
|
|
compatible = "visionox,rm69299-1080p-display";
|
|
reg = <0>;
|
|
|
|
vdda-supply = <&vreg_l8c_1p8>;
|
|
vdd3p3-supply = <&vreg_l18a_2p8>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&disp_pins>;
|
|
|
|
reset-gpios = <&pm6150l_gpio 3 GPIO_ACTIVE_HIGH>;
|
|
|
|
ports {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
port@0 {
|
|
reg = <0>;
|
|
panel0_in: endpoint {
|
|
remote-endpoint = <&dsi0_out>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
ports {
|
|
port@1 {
|
|
endpoint {
|
|
remote-endpoint = <&panel0_in>;
|
|
data-lanes = <0 1 2 3>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&dsi_phy {
|
|
status = "okay";
|
|
vdds-supply = <&vreg_l4a_0p8>;
|
|
};
|
|
|
|
&mdp {
|
|
status = "okay";
|
|
};
|
|
|
|
&mdss {
|
|
status = "okay";
|
|
};
|
|
|
|
&qfprom {
|
|
vcc-supply = <&vreg_l11a_1p8>;
|
|
};
|
|
|
|
&qspi {
|
|
status = "okay";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&qspi_clk &qspi_cs0 &qspi_data01>;
|
|
|
|
flash@0 {
|
|
compatible = "jedec,spi-nor";
|
|
reg = <0>;
|
|
spi-max-frequency = <25000000>;
|
|
spi-tx-bus-width = <2>;
|
|
spi-rx-bus-width = <2>;
|
|
};
|
|
};
|
|
|
|
&qupv3_id_0 {
|
|
status = "okay";
|
|
};
|
|
|
|
&qupv3_id_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&remoteproc_mpss {
|
|
status = "okay";
|
|
compatible = "qcom,sc7180-mss-pil";
|
|
iommus = <&apps_smmu 0x461 0x0>, <&apps_smmu 0x444 0x3>;
|
|
memory-region = <&mba_mem &mpss_mem>;
|
|
};
|
|
|
|
&sdhc_1 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-0 = <&sdc1_on>;
|
|
pinctrl-1 = <&sdc1_off>;
|
|
vmmc-supply = <&vreg_l19a_2p9>;
|
|
vqmmc-supply = <&vreg_l12a_1p8>;
|
|
};
|
|
|
|
&sdhc_2 {
|
|
status = "okay";
|
|
|
|
pinctrl-names = "default","sleep";
|
|
pinctrl-0 = <&sdc2_on>;
|
|
pinctrl-1 = <&sdc2_off>;
|
|
vmmc-supply = <&vreg_l9c_2p9>;
|
|
vqmmc-supply = <&vreg_l6c_2p9>;
|
|
|
|
cd-gpios = <&tlmm 69 GPIO_ACTIVE_LOW>;
|
|
};
|
|
|
|
&uart3 {
|
|
status = "okay";
|
|
|
|
/delete-property/interrupts;
|
|
interrupts-extended = <&intc GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
|
|
<&tlmm 41 IRQ_TYPE_EDGE_FALLING>;
|
|
|
|
pinctrl-names = "default", "sleep";
|
|
pinctrl-1 = <&qup_uart3_sleep>;
|
|
|
|
bluetooth: wcn3990-bt {
|
|
compatible = "qcom,wcn3990-bt";
|
|
vddio-supply = <&vreg_l10a_1p8>;
|
|
vddxo-supply = <&vreg_l1c_1p8>;
|
|
vddrf-supply = <&vreg_l2c_1p3>;
|
|
vddch0-supply = <&vreg_l10c_3p3>;
|
|
max-speed = <3200000>;
|
|
};
|
|
};
|
|
|
|
&uart8 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_1 {
|
|
status = "okay";
|
|
};
|
|
|
|
&usb_1_dwc3 {
|
|
dr_mode = "host";
|
|
};
|
|
|
|
&usb_1_hsphy {
|
|
status = "okay";
|
|
vdd-supply = <&vreg_l4a_0p8>;
|
|
vdda-pll-supply = <&vreg_l11a_1p8>;
|
|
vdda-phy-dpdm-supply = <&vreg_l17a_3p0>;
|
|
qcom,imp-res-offset-value = <8>;
|
|
qcom,preemphasis-level = <QUSB2_V2_PREEMPHASIS_15_PERCENT>;
|
|
qcom,preemphasis-width = <QUSB2_V2_PREEMPHASIS_WIDTH_HALF_BIT>;
|
|
qcom,bias-ctrl-value = <0x22>;
|
|
qcom,charge-ctrl-value = <3>;
|
|
qcom,hsdisc-trim-value = <0>;
|
|
};
|
|
|
|
&usb_1_qmpphy {
|
|
status = "okay";
|
|
vdda-phy-supply = <&vreg_l3c_1p2>;
|
|
vdda-pll-supply = <&vreg_l4a_0p8>;
|
|
};
|
|
|
|
&venus {
|
|
video-firmware {
|
|
iommus = <&apps_smmu 0x0c42 0x0>;
|
|
};
|
|
};
|
|
|
|
&wifi {
|
|
status = "okay";
|
|
vdd-0.8-cx-mx-supply = <&vreg_l9a_0p6>;
|
|
vdd-1.8-xo-supply = <&vreg_l1c_1p8>;
|
|
vdd-1.3-rfa-supply = <&vreg_l2c_1p3>;
|
|
vdd-3.3-ch0-supply = <&vreg_l10c_3p3>;
|
|
vdd-3.3-ch1-supply = <&vreg_l11c_3p3>;
|
|
wifi-firmware {
|
|
iommus = <&apps_smmu 0xc2 0x1>;
|
|
};
|
|
};
|
|
|
|
/* PINCTRL - additions to nodes defined in sc7180.dtsi */
|
|
|
|
&pm6150l_gpio {
|
|
disp_pins: disp-state {
|
|
pinconf {
|
|
pins = "gpio3";
|
|
function = PMIC_GPIO_FUNC_FUNC1;
|
|
qcom,drive-strength = <PMIC_GPIO_STRENGTH_MED>;
|
|
power-source = <0>;
|
|
bias-disable;
|
|
output-low;
|
|
};
|
|
};
|
|
};
|
|
|
|
&qspi_clk {
|
|
pinconf {
|
|
pins = "gpio63";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&qspi_cs0 {
|
|
pinconf {
|
|
pins = "gpio68";
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&qspi_data01 {
|
|
pinconf {
|
|
pins = "gpio64", "gpio65";
|
|
|
|
/* High-Z when no transfers; nice to park the lines */
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
&qup_i2c2_default {
|
|
pinconf {
|
|
pins = "gpio15", "gpio16";
|
|
drive-strength = <2>;
|
|
|
|
/* Has external pullup */
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&qup_i2c4_default {
|
|
pinconf {
|
|
pins = "gpio115", "gpio116";
|
|
drive-strength = <2>;
|
|
|
|
/* Has external pullup */
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&qup_i2c7_default {
|
|
pinconf {
|
|
pins = "gpio6", "gpio7";
|
|
drive-strength = <2>;
|
|
|
|
/* Has external pullup */
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&qup_i2c9_default {
|
|
pinconf {
|
|
pins = "gpio46", "gpio47";
|
|
drive-strength = <2>;
|
|
|
|
/* Has external pullup */
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&qup_uart3_default {
|
|
pinconf-cts {
|
|
/*
|
|
* Configure a pull-down on CTS to match the pull of
|
|
* the Bluetooth module.
|
|
*/
|
|
pins = "gpio38";
|
|
bias-pull-down;
|
|
};
|
|
|
|
pinconf-rts {
|
|
/* We'll drive RTS, so no pull */
|
|
pins = "gpio39";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinconf-tx {
|
|
/* We'll drive TX, so no pull */
|
|
pins = "gpio40";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinconf-rx {
|
|
/*
|
|
* Configure a pull-up on RX. This is needed to avoid
|
|
* garbage data when the TX pin of the Bluetooth module is
|
|
* in tri-state (module powered off or not driving the
|
|
* signal yet).
|
|
*/
|
|
pins = "gpio41";
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
&qup_uart8_default {
|
|
pinconf-tx {
|
|
pins = "gpio44";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
|
|
pinconf-rx {
|
|
pins = "gpio45";
|
|
drive-strength = <2>;
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
&qup_spi0_default {
|
|
pinconf {
|
|
pins = "gpio34", "gpio35", "gpio36", "gpio37";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&qup_spi6_default {
|
|
pinconf {
|
|
pins = "gpio59", "gpio60", "gpio61", "gpio62";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&qup_spi10_default {
|
|
pinconf {
|
|
pins = "gpio86", "gpio87", "gpio88", "gpio89";
|
|
drive-strength = <2>;
|
|
bias-disable;
|
|
};
|
|
};
|
|
|
|
&tlmm {
|
|
qup_uart3_sleep: qup-uart3-sleep {
|
|
pinmux {
|
|
pins = "gpio38", "gpio39",
|
|
"gpio40", "gpio41";
|
|
function = "gpio";
|
|
};
|
|
|
|
pinconf-cts {
|
|
/*
|
|
* Configure a pull-down on CTS to match the pull of
|
|
* the Bluetooth module.
|
|
*/
|
|
pins = "gpio38";
|
|
bias-pull-down;
|
|
};
|
|
|
|
pinconf-rts {
|
|
/*
|
|
* Configure pull-down on RTS. As RTS is active low
|
|
* signal, pull it low to indicate the BT SoC that it
|
|
* can wakeup the system anytime from suspend state by
|
|
* pulling RX low (by sending wakeup bytes).
|
|
*/
|
|
pins = "gpio39";
|
|
bias-pull-down;
|
|
};
|
|
|
|
pinconf-tx {
|
|
/*
|
|
* Configure pull-up on TX when it isn't actively driven
|
|
* to prevent BT SoC from receiving garbage during sleep.
|
|
*/
|
|
pins = "gpio40";
|
|
bias-pull-up;
|
|
};
|
|
|
|
pinconf-rx {
|
|
/*
|
|
* Configure a pull-up on RX. This is needed to avoid
|
|
* garbage data when the TX pin of the Bluetooth module
|
|
* is floating which may cause spurious wakeups.
|
|
*/
|
|
pins = "gpio41";
|
|
bias-pull-up;
|
|
};
|
|
};
|
|
|
|
sdc1_on: sdc1-on {
|
|
pinconf-clk {
|
|
pins = "sdc1_clk";
|
|
bias-disable;
|
|
drive-strength = <16>;
|
|
};
|
|
|
|
pinconf-cmd {
|
|
pins = "sdc1_cmd";
|
|
bias-pull-up;
|
|
drive-strength = <10>;
|
|
};
|
|
|
|
pinconf-data {
|
|
pins = "sdc1_data";
|
|
bias-pull-up;
|
|
drive-strength = <10>;
|
|
};
|
|
|
|
pinconf-rclk {
|
|
pins = "sdc1_rclk";
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
|
|
sdc1_off: sdc1-off {
|
|
pinconf-clk {
|
|
pins = "sdc1_clk";
|
|
bias-disable;
|
|
drive-strength = <2>;
|
|
};
|
|
|
|
pinconf-cmd {
|
|
pins = "sdc1_cmd";
|
|
bias-pull-up;
|
|
drive-strength = <2>;
|
|
};
|
|
|
|
pinconf-data {
|
|
pins = "sdc1_data";
|
|
bias-pull-up;
|
|
drive-strength = <2>;
|
|
};
|
|
|
|
pinconf-rclk {
|
|
pins = "sdc1_rclk";
|
|
bias-pull-down;
|
|
};
|
|
};
|
|
|
|
sdc2_on: sdc2-on {
|
|
pinconf-clk {
|
|
pins = "sdc2_clk";
|
|
bias-disable;
|
|
drive-strength = <16>;
|
|
};
|
|
|
|
pinconf-cmd {
|
|
pins = "sdc2_cmd";
|
|
bias-pull-up;
|
|
drive-strength = <10>;
|
|
};
|
|
|
|
pinconf-data {
|
|
pins = "sdc2_data";
|
|
bias-pull-up;
|
|
drive-strength = <10>;
|
|
};
|
|
|
|
pinconf-sd-cd {
|
|
pins = "gpio69";
|
|
bias-pull-up;
|
|
drive-strength = <2>;
|
|
};
|
|
};
|
|
|
|
sdc2_off: sdc2-off {
|
|
pinconf-clk {
|
|
pins = "sdc2_clk";
|
|
bias-disable;
|
|
drive-strength = <2>;
|
|
};
|
|
|
|
pinconf-cmd {
|
|
pins = "sdc2_cmd";
|
|
bias-pull-up;
|
|
drive-strength = <2>;
|
|
};
|
|
|
|
pinconf-data {
|
|
pins = "sdc2_data";
|
|
bias-pull-up;
|
|
drive-strength = <2>;
|
|
};
|
|
|
|
pinconf-sd-cd {
|
|
pins = "gpio69";
|
|
bias-pull-up;
|
|
drive-strength = <2>;
|
|
};
|
|
};
|
|
};
|