138 lines
6.3 KiB
ReStructuredText
138 lines
6.3 KiB
ReStructuredText
.. include:: <isonum.txt>
|
|
|
|
=========================
|
|
N-Trig touchscreen Driver
|
|
=========================
|
|
|
|
:Copyright: |copy| 2008-2010 Rafi Rubin <rafi@seas.upenn.edu>
|
|
:Copyright: |copy| 2009-2010 Stephane Chatty
|
|
|
|
This driver provides support for N-Trig pen and multi-touch sensors. Single
|
|
and multi-touch events are translated to the appropriate protocols for
|
|
the hid and input systems. Pen events are sufficiently hid compliant and
|
|
are left to the hid core. The driver also provides additional filtering
|
|
and utility functions accessible with sysfs and module parameters.
|
|
|
|
This driver has been reported to work properly with multiple N-Trig devices
|
|
attached.
|
|
|
|
|
|
Parameters
|
|
----------
|
|
|
|
Note: values set at load time are global and will apply to all applicable
|
|
devices. Adjusting parameters with sysfs will override the load time values,
|
|
but only for that one device.
|
|
|
|
The following parameters are used to configure filters to reduce noise:
|
|
|
|
+-----------------------+-----------------------------------------------------+
|
|
|activate_slack |number of fingers to ignore before processing events |
|
|
+-----------------------+-----------------------------------------------------+
|
|
|activation_height, |size threshold to activate immediately |
|
|
|activation_width | |
|
|
+-----------------------+-----------------------------------------------------+
|
|
|min_height, |size threshold below which fingers are ignored |
|
|
|min_width |both to decide activation and during activity |
|
|
+-----------------------+-----------------------------------------------------+
|
|
|deactivate_slack |the number of "no contact" frames to ignore before |
|
|
| |propagating the end of activity events |
|
|
+-----------------------+-----------------------------------------------------+
|
|
|
|
When the last finger is removed from the device, it sends a number of empty
|
|
frames. By holding off on deactivation for a few frames we can tolerate false
|
|
erroneous disconnects, where the sensor may mistakenly not detect a finger that
|
|
is still present. Thus deactivate_slack addresses problems where a users might
|
|
see breaks in lines during drawing, or drop an object during a long drag.
|
|
|
|
|
|
Additional sysfs items
|
|
----------------------
|
|
|
|
These nodes just provide easy access to the ranges reported by the device.
|
|
|
|
+-----------------------+-----------------------------------------------------+
|
|
|sensor_logical_height, | the range for positions reported during activity |
|
|
|sensor_logical_width | |
|
|
+-----------------------+-----------------------------------------------------+
|
|
|sensor_physical_height,| internal ranges not used for normal events but |
|
|
|sensor_physical_width | useful for tuning |
|
|
+-----------------------+-----------------------------------------------------+
|
|
|
|
All N-Trig devices with product id of 1 report events in the ranges of
|
|
|
|
* X: 0-9600
|
|
* Y: 0-7200
|
|
|
|
However not all of these devices have the same physical dimensions. Most
|
|
seem to be 12" sensors (Dell Latitude XT and XT2 and the HP TX2), and
|
|
at least one model (Dell Studio 17) has a 17" sensor. The ratio of physical
|
|
to logical sizes is used to adjust the size based filter parameters.
|
|
|
|
|
|
Filtering
|
|
---------
|
|
|
|
With the release of the early multi-touch firmwares it became increasingly
|
|
obvious that these sensors were prone to erroneous events. Users reported
|
|
seeing both inappropriately dropped contact and ghosts, contacts reported
|
|
where no finger was actually touching the screen.
|
|
|
|
Deactivation slack helps prevent dropped contact for single touch use, but does
|
|
not address the problem of dropping one of more contacts while other contacts
|
|
are still active. Drops in the multi-touch context require additional
|
|
processing and should be handled in tandem with tacking.
|
|
|
|
As observed ghost contacts are similar to actual use of the sensor, but they
|
|
seem to have different profiles. Ghost activity typically shows up as small
|
|
short lived touches. As such, I assume that the longer the continuous stream
|
|
of events the more likely those events are from a real contact, and that the
|
|
larger the size of each contact the more likely it is real. Balancing the
|
|
goals of preventing ghosts and accepting real events quickly (to minimize
|
|
user observable latency), the filter accumulates confidence for incoming
|
|
events until it hits thresholds and begins propagating. In the interest in
|
|
minimizing stored state as well as the cost of operations to make a decision,
|
|
I've kept that decision simple.
|
|
|
|
Time is measured in terms of the number of fingers reported, not frames since
|
|
the probability of multiple simultaneous ghosts is expected to drop off
|
|
dramatically with increasing numbers. Rather than accumulate weight as a
|
|
function of size, I just use it as a binary threshold. A sufficiently large
|
|
contact immediately overrides the waiting period and leads to activation.
|
|
|
|
Setting the activation size thresholds to large values will result in deciding
|
|
primarily on activation slack. If you see longer lived ghosts, turning up the
|
|
activation slack while reducing the size thresholds may suffice to eliminate
|
|
the ghosts while keeping the screen quite responsive to firm taps.
|
|
|
|
Contacts continue to be filtered with min_height and min_width even after
|
|
the initial activation filter is satisfied. The intent is to provide
|
|
a mechanism for filtering out ghosts in the form of an extra finger while
|
|
you actually are using the screen. In practice this sort of ghost has
|
|
been far less problematic or relatively rare and I've left the defaults
|
|
set to 0 for both parameters, effectively turning off that filter.
|
|
|
|
I don't know what the optimal values are for these filters. If the defaults
|
|
don't work for you, please play with the parameters. If you do find other
|
|
values more comfortable, I would appreciate feedback.
|
|
|
|
The calibration of these devices does drift over time. If ghosts or contact
|
|
dropping worsen and interfere with the normal usage of your device, try
|
|
recalibrating it.
|
|
|
|
|
|
Calibration
|
|
-----------
|
|
|
|
The N-Trig windows tools provide calibration and testing routines. Also an
|
|
unofficial unsupported set of user space tools including a calibrator is
|
|
available at:
|
|
http://code.launchpad.net/~rafi-seas/+junk/ntrig_calib
|
|
|
|
|
|
Tracking
|
|
--------
|
|
|
|
As of yet, all tested N-Trig firmwares do not track fingers. When multiple
|
|
contacts are active they seem to be sorted primarily by Y position.
|