124 lines
3.8 KiB
YAML
124 lines
3.8 KiB
YAML
# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/mfd/rohm,bd9576-pmic.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: ROHM BD9576MUF and BD9573MUF Power Management Integrated Circuit bindings
|
|
|
|
maintainers:
|
|
- Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
|
|
|
|
description: |
|
|
BD9576MUF and BD9573MUF are power management ICs primarily intended for
|
|
powering the R-Car series processors.
|
|
The IC provides 6 power outputs with configurable sequencing and safety
|
|
monitoring. A watchdog logic with slow ping/windowed modes is also included.
|
|
|
|
properties:
|
|
compatible:
|
|
enum:
|
|
- rohm,bd9576
|
|
- rohm,bd9573
|
|
|
|
reg:
|
|
description:
|
|
I2C slave address.
|
|
maxItems: 1
|
|
|
|
interrupts:
|
|
maxItems: 1
|
|
|
|
rohm,vout1-en-low:
|
|
description:
|
|
BD9576 and BD9573 VOUT1 regulator enable state can be individually
|
|
controlled by a GPIO. This is dictated by state of vout1-en pin during
|
|
the PMIC startup. If vout1-en is LOW during PMIC startup then the VOUT1
|
|
enable sate is controlled via this pin. Set this property if vout1-en
|
|
is wired to be down at PMIC start-up.
|
|
type: boolean
|
|
|
|
rohm,vout1-en-gpios:
|
|
description:
|
|
GPIO specifier to specify the GPIO connected to vout1-en for vout1 ON/OFF
|
|
state control.
|
|
maxItems: 1
|
|
|
|
rohm,ddr-sel-low:
|
|
description:
|
|
The BD9576 and BD9573 output voltage for DDR can be selected by setting
|
|
the ddr-sel pin low or high. Set this property if ddr-sel is grounded.
|
|
type: boolean
|
|
|
|
rohm,watchdog-enable-gpios:
|
|
description: The GPIO line used to enable the watchdog.
|
|
maxItems: 1
|
|
|
|
rohm,watchdog-ping-gpios:
|
|
description: The GPIO line used to ping the watchdog.
|
|
maxItems: 1
|
|
|
|
rohm,hw-timeout-ms:
|
|
maxItems: 2
|
|
description:
|
|
Watchog timeout in milliseconds. If single value is given it is
|
|
the maximum timeout. Eg. if pinging watchdog is not done within this time
|
|
limit the watchdog will be triggered. If two values are given watchdog
|
|
is configured in "window mode". Then first value is limit for short-ping
|
|
Eg. if watchdog is pinged sooner than that the watchdog will trigger.
|
|
When two values is given the second value is the maximum timeout.
|
|
# (HW) minimum for short timeout is 2ms, maximum 220 ms.
|
|
# (HW) minimum for max timeout is 4ms, maximum 4416 ms.
|
|
|
|
regulators:
|
|
$ref: ../regulator/rohm,bd9576-regulator.yaml
|
|
description:
|
|
List of child nodes that specify the regulators.
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- regulators
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/leds/common.h>
|
|
i2c {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
pmic: pmic@30 {
|
|
compatible = "rohm,bd9576";
|
|
reg = <0x30>;
|
|
rohm,vout1-en-low;
|
|
rohm,vout1-en-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
|
|
rohm,ddr-sel-low;
|
|
rohm,watchdog-enable-gpios = <&gpio2 6 GPIO_ACTIVE_HIGH>;
|
|
rohm,watchdog-ping-gpios = <&gpio2 7 GPIO_ACTIVE_HIGH>;
|
|
rohm,hw-timeout-ms = <150>, <2300>;
|
|
|
|
regulators {
|
|
boost1: regulator-vd50 {
|
|
regulator-name = "VD50";
|
|
};
|
|
buck1: regulator-vd18 {
|
|
regulator-name = "VD18";
|
|
};
|
|
buck2: regulator-vdddr {
|
|
regulator-name = "VDDDR";
|
|
};
|
|
buck3: regulator-vd10 {
|
|
regulator-name = "VD10";
|
|
};
|
|
ldo: regulator-voutl1 {
|
|
regulator-name = "VOUTL1";
|
|
};
|
|
sw: regulator-vouts1 {
|
|
regulator-name = "VOUTS1";
|
|
};
|
|
};
|
|
};
|
|
};
|