143 lines
3.9 KiB
YAML
143 lines
3.9 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: "http://devicetree.org/schemas/net/sff,sfp.yaml#"
|
|
$schema: "http://devicetree.org/meta-schemas/core.yaml#"
|
|
|
|
title: Small Form Factor (SFF) Committee Small Form-factor Pluggable (SFP)
|
|
Transceiver
|
|
|
|
maintainers:
|
|
- Russell King <linux@armlinux.org.uk>
|
|
|
|
properties:
|
|
compatible:
|
|
enum:
|
|
- sff,sfp # for SFP modules
|
|
- sff,sff # for soldered down SFF modules
|
|
|
|
i2c-bus:
|
|
$ref: /schemas/types.yaml#/definitions/phandle
|
|
description:
|
|
phandle of an I2C bus controller for the SFP two wire serial
|
|
|
|
maximum-power-milliwatt:
|
|
maxItems: 1
|
|
description:
|
|
Maximum module power consumption Specifies the maximum power consumption
|
|
allowable by a module in the slot, in milli-Watts. Presently, modules can
|
|
be up to 1W, 1.5W or 2W.
|
|
|
|
"mod-def0-gpios":
|
|
maxItems: 1
|
|
description:
|
|
GPIO phandle and a specifier of the MOD-DEF0 (AKA Mod_ABS) module
|
|
presence input gpio signal, active (module absent) high. Must not be
|
|
present for SFF modules
|
|
|
|
"los-gpios":
|
|
maxItems: 1
|
|
description:
|
|
GPIO phandle and a specifier of the Receiver Loss of Signal Indication
|
|
input gpio signal, active (signal lost) high
|
|
|
|
"tx-fault-gpios":
|
|
maxItems: 1
|
|
description:
|
|
GPIO phandle and a specifier of the Module Transmitter Fault input gpio
|
|
signal, active (fault condition) high
|
|
|
|
"tx-disable-gpios":
|
|
maxItems: 1
|
|
description:
|
|
GPIO phandle and a specifier of the Transmitter Disable output gpio
|
|
signal, active (Tx disable) high
|
|
|
|
"rate-select0-gpios":
|
|
maxItems: 1
|
|
description:
|
|
GPIO phandle and a specifier of the Rx Signaling Rate Select (AKA RS0)
|
|
output gpio signal, low - low Rx rate, high - high Rx rate Must not be
|
|
present for SFF modules
|
|
|
|
"rate-select1-gpios":
|
|
maxItems: 1
|
|
description:
|
|
GPIO phandle and a specifier of the Tx Signaling Rate Select (AKA RS1)
|
|
output gpio signal (SFP+ only), low - low Tx rate, high - high Tx rate. Must
|
|
not be present for SFF modules
|
|
|
|
allOf:
|
|
- if:
|
|
properties:
|
|
compatible:
|
|
contains:
|
|
const: sff,sff
|
|
then:
|
|
properties:
|
|
mod-def0-gpios: false
|
|
rate-select0-gpios: false
|
|
rate-select1-gpios: false
|
|
|
|
required:
|
|
- compatible
|
|
- i2c-bus
|
|
|
|
additionalProperties: false
|
|
|
|
examples:
|
|
- | # Direct serdes to SFP connection
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
|
|
sfp1: sfp {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&sfp_1g_i2c>;
|
|
los-gpios = <&cpm_gpio2 22 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpios = <&cpm_gpio2 21 GPIO_ACTIVE_LOW>;
|
|
maximum-power-milliwatt = <1000>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cpm_sfp_1g_pins &cps_sfp_1g_pins>;
|
|
tx-disable-gpios = <&cps_gpio1 24 GPIO_ACTIVE_HIGH>;
|
|
tx-fault-gpios = <&cpm_gpio2 19 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
ethernet {
|
|
phy-names = "comphy";
|
|
phys = <&cps_comphy5 0>;
|
|
sfp = <&sfp1>;
|
|
};
|
|
|
|
- | # Serdes to PHY to SFP connection
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
|
|
sfp2: sfp {
|
|
compatible = "sff,sfp";
|
|
i2c-bus = <&sfp_i2c>;
|
|
los-gpios = <&cps_gpio1 28 GPIO_ACTIVE_HIGH>;
|
|
mod-def0-gpios = <&cps_gpio1 27 GPIO_ACTIVE_LOW>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cps_sfpp0_pins>;
|
|
tx-disable-gpios = <&cps_gpio1 29 GPIO_ACTIVE_HIGH>;
|
|
tx-fault-gpios = <&cps_gpio1 26 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
mdio {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
phy: ethernet-phy@0 {
|
|
compatible = "ethernet-phy-ieee802.3-c45";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&cpm_phy0_pins &cps_phy0_pins>;
|
|
reg = <0>;
|
|
interrupt = <&cpm_gpio2 18 IRQ_TYPE_EDGE_FALLING>;
|
|
sfp = <&sfp2>;
|
|
};
|
|
};
|
|
|
|
ethernet {
|
|
phy = <&phy>;
|
|
phy-mode = "10gbase-kr";
|
|
};
|