127 lines
4.5 KiB
Plaintext
127 lines
4.5 KiB
Plaintext
Marvell NAND Flash Controller (NFC)
|
|
|
|
Required properties:
|
|
- compatible: can be one of the following:
|
|
* "marvell,armada-8k-nand-controller"
|
|
* "marvell,armada370-nand-controller"
|
|
* "marvell,pxa3xx-nand-controller"
|
|
* "marvell,armada-8k-nand" (deprecated)
|
|
* "marvell,armada370-nand" (deprecated)
|
|
* "marvell,pxa3xx-nand" (deprecated)
|
|
Compatibles marked deprecated support only the old bindings described
|
|
at the bottom.
|
|
- reg: NAND flash controller memory area.
|
|
- #address-cells: shall be set to 1. Encode the NAND CS.
|
|
- #size-cells: shall be set to 0.
|
|
- interrupts: shall define the NAND controller interrupt.
|
|
- clocks: shall reference the NAND controller clocks, the second one is
|
|
is only needed for the Armada 7K/8K SoCs
|
|
- clock-names: mandatory if there is a second clock, in this case there
|
|
should be one clock named "core" and another one named "reg"
|
|
- marvell,system-controller: Set to retrieve the syscon node that handles
|
|
NAND controller related registers (only required with the
|
|
"marvell,armada-8k-nand[-controller]" compatibles).
|
|
|
|
Optional properties:
|
|
- label: see partition.txt. New platforms shall omit this property.
|
|
- dmas: shall reference DMA channel associated to the NAND controller.
|
|
This property is only used with "marvell,pxa3xx-nand[-controller]"
|
|
compatible strings.
|
|
- dma-names: shall be "rxtx".
|
|
This property is only used with "marvell,pxa3xx-nand[-controller]"
|
|
compatible strings.
|
|
|
|
Optional children nodes:
|
|
Children nodes represent the available NAND chips.
|
|
|
|
Required properties:
|
|
- reg: shall contain the native Chip Select ids (0-3).
|
|
- nand-rb: see nand-controller.yaml (0-1).
|
|
|
|
Optional properties:
|
|
- marvell,nand-keep-config: orders the driver not to take the timings
|
|
from the core and leaving them completely untouched. Bootloader
|
|
timings will then be used.
|
|
- label: MTD name.
|
|
- nand-on-flash-bbt: see nand-controller.yaml.
|
|
- nand-ecc-mode: see nand-controller.yaml. Will use hardware ECC if not specified.
|
|
- nand-ecc-algo: see nand-controller.yaml. This property is essentially useful when
|
|
not using hardware ECC. Howerver, it may be added when using hardware
|
|
ECC for clarification but will be ignored by the driver because ECC
|
|
mode is chosen depending on the page size and the strength required by
|
|
the NAND chip. This value may be overwritten with nand-ecc-strength
|
|
property.
|
|
- nand-ecc-strength: see nand-controller.yaml.
|
|
- nand-ecc-step-size: see nand-controller.yaml. Marvell's NAND flash controller does
|
|
use fixed strength (1-bit for Hamming, 16-bit for BCH), so the actual
|
|
step size will shrink or grow in order to fit the required strength.
|
|
Step sizes are not completely random for all and follow certain
|
|
patterns described in AN-379, "Marvell SoC NFC ECC".
|
|
|
|
See Documentation/devicetree/bindings/mtd/nand-controller.yaml for more details on
|
|
generic bindings.
|
|
|
|
|
|
Example:
|
|
nand_controller: nand-controller@d0000 {
|
|
compatible = "marvell,armada370-nand-controller";
|
|
reg = <0xd0000 0x54>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>;
|
|
clocks = <&coredivclk 0>;
|
|
|
|
nand@0 {
|
|
reg = <0>;
|
|
label = "main-storage";
|
|
nand-rb = <0>;
|
|
nand-ecc-mode = "hw";
|
|
marvell,nand-keep-config;
|
|
nand-on-flash-bbt;
|
|
nand-ecc-strength = <4>;
|
|
nand-ecc-step-size = <512>;
|
|
|
|
partitions {
|
|
compatible = "fixed-partitions";
|
|
#address-cells = <1>;
|
|
#size-cells = <1>;
|
|
|
|
partition@0 {
|
|
label = "Rootfs";
|
|
reg = <0x00000000 0x40000000>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
|
|
Note on legacy bindings: One can find, in not-updated device trees,
|
|
bindings slightly different than described above with other properties
|
|
described below as well as the partitions node at the root of a so
|
|
called "nand" node (without clear controller/chip separation).
|
|
|
|
Legacy properties:
|
|
- marvell,nand-enable-arbiter: To enable the arbiter, all boards blindly
|
|
used it, this bit was set by the bootloader for many boards and even if
|
|
it is marked reserved in several datasheets, it might be needed to set
|
|
it (otherwise it is harmless) so whether or not this property is set,
|
|
the bit is selected by the driver.
|
|
- num-cs: Number of chip-select lines to use, all boards blindly set 1
|
|
to this and for a reason, other values would have failed. The value of
|
|
this property is ignored.
|
|
|
|
Example:
|
|
|
|
nand0: nand@43100000 {
|
|
compatible = "marvell,pxa3xx-nand";
|
|
reg = <0x43100000 90>;
|
|
interrupts = <45>;
|
|
dmas = <&pdma 97 0>;
|
|
dma-names = "rxtx";
|
|
#address-cells = <1>;
|
|
marvell,nand-keep-config;
|
|
marvell,nand-enable-arbiter;
|
|
num-cs = <1>;
|
|
/* Partitions (optional) */
|
|
};
|