117 lines
3.5 KiB
YAML
117 lines
3.5 KiB
YAML
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
|
%YAML 1.2
|
|
---
|
|
$id: http://devicetree.org/schemas/dma/st,stm32-dma.yaml#
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
|
|
|
title: STMicroelectronics STM32 DMA Controller bindings
|
|
|
|
description: |
|
|
The STM32 DMA is a general-purpose direct memory access controller capable of
|
|
supporting 8 independent DMA channels. Each channel can have up to 8 requests.
|
|
DMA clients connected to the STM32 DMA controller must use the format
|
|
described in the dma.txt file, using a four-cell specifier for each
|
|
channel: a phandle to the DMA controller plus the following four integer cells:
|
|
1. The channel id
|
|
2. The request line number
|
|
3. A 32bit mask specifying the DMA channel configuration which are device
|
|
dependent:
|
|
-bit 9: Peripheral Increment Address
|
|
0x0: no address increment between transfers
|
|
0x1: increment address between transfers
|
|
-bit 10: Memory Increment Address
|
|
0x0: no address increment between transfers
|
|
0x1: increment address between transfers
|
|
-bit 15: Peripheral Increment Offset Size
|
|
0x0: offset size is linked to the peripheral bus width
|
|
0x1: offset size is fixed to 4 (32-bit alignment)
|
|
-bit 16-17: Priority level
|
|
0x0: low
|
|
0x1: medium
|
|
0x2: high
|
|
0x3: very high
|
|
4. A 32bit bitfield value specifying DMA features which are device dependent:
|
|
-bit 0-1: DMA FIFO threshold selection
|
|
0x0: 1/4 full FIFO
|
|
0x1: 1/2 full FIFO
|
|
0x2: 3/4 full FIFO
|
|
0x3: full FIFO
|
|
-bit 2: DMA direct mode
|
|
0x0: FIFO mode with threshold selectable with bit 0-1
|
|
0x1: Direct mode: each DMA request immediately initiates a transfer
|
|
from/to the memory, FIFO is bypassed.
|
|
-bit 4: alternative DMA request/acknowledge protocol
|
|
0x0: Use standard DMA ACK management, where ACK signal is maintained
|
|
up to the removal of request and transfer completion
|
|
0x1: Use alternative DMA ACK management, where ACK de-assertion does
|
|
not wait for the de-assertion of the REQuest, ACK is only managed
|
|
by transfer completion. This must only be used on channels
|
|
managing transfers for STM32 USART/UART.
|
|
|
|
|
|
maintainers:
|
|
- Amelie Delaunay <amelie.delaunay@foss.st.com>
|
|
|
|
allOf:
|
|
- $ref: "dma-controller.yaml#"
|
|
|
|
properties:
|
|
"#dma-cells":
|
|
const: 4
|
|
|
|
compatible:
|
|
const: st,stm32-dma
|
|
|
|
reg:
|
|
maxItems: 1
|
|
|
|
clocks:
|
|
maxItems: 1
|
|
|
|
interrupts:
|
|
maxItems: 8
|
|
description: Should contain all of the per-channel DMA
|
|
interrupts in ascending order with respect to the
|
|
DMA channel index.
|
|
|
|
resets:
|
|
maxItems: 1
|
|
|
|
st,mem2mem:
|
|
$ref: /schemas/types.yaml#/definitions/flag
|
|
description: if defined, it indicates that the controller
|
|
supports memory-to-memory transfer
|
|
|
|
required:
|
|
- compatible
|
|
- reg
|
|
- clocks
|
|
- interrupts
|
|
|
|
unevaluatedProperties: false
|
|
|
|
examples:
|
|
- |
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
|
#include <dt-bindings/clock/stm32mp1-clks.h>
|
|
#include <dt-bindings/reset/stm32mp1-resets.h>
|
|
dma-controller@40026400 {
|
|
compatible = "st,stm32-dma";
|
|
reg = <0x40026400 0x400>;
|
|
interrupts = <56>,
|
|
<57>,
|
|
<58>,
|
|
<59>,
|
|
<60>,
|
|
<68>,
|
|
<69>,
|
|
<70>;
|
|
clocks = <&clk_hclk>;
|
|
#dma-cells = <4>;
|
|
st,mem2mem;
|
|
resets = <&rcc 150>;
|
|
dma-requests = <8>;
|
|
};
|
|
|
|
...
|