1813 lines
41 KiB
C
1813 lines
41 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* Davicom DM9000 Fast Ethernet driver for Linux.
|
|
* Copyright (C) 1997 Sten Wang
|
|
*
|
|
* (C) Copyright 1997-1998 DAVICOM Semiconductor,Inc. All Rights Reserved.
|
|
*
|
|
* Additional updates, Copyright:
|
|
* Ben Dooks <ben@simtec.co.uk>
|
|
* Sascha Hauer <s.hauer@pengutronix.de>
|
|
*/
|
|
|
|
#include <linux/module.h>
|
|
#include <linux/ioport.h>
|
|
#include <linux/netdevice.h>
|
|
#include <linux/etherdevice.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/skbuff.h>
|
|
#include <linux/spinlock.h>
|
|
#include <linux/crc32.h>
|
|
#include <linux/mii.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_net.h>
|
|
#include <linux/ethtool.h>
|
|
#include <linux/dm9000.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/irq.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/gpio/consumer.h>
|
|
|
|
#include <asm/delay.h>
|
|
#include <asm/irq.h>
|
|
#include <asm/io.h>
|
|
|
|
#include "dm9000.h"
|
|
|
|
/* Board/System/Debug information/definition ---------------- */
|
|
|
|
#define DM9000_PHY 0x40 /* PHY address 0x01 */
|
|
|
|
#define CARDNAME "dm9000"
|
|
|
|
/*
|
|
* Transmit timeout, default 5 seconds.
|
|
*/
|
|
static int watchdog = 5000;
|
|
module_param(watchdog, int, 0400);
|
|
MODULE_PARM_DESC(watchdog, "transmit timeout in milliseconds");
|
|
|
|
/*
|
|
* Debug messages level
|
|
*/
|
|
static int debug;
|
|
module_param(debug, int, 0644);
|
|
MODULE_PARM_DESC(debug, "dm9000 debug level (0-6)");
|
|
|
|
/* DM9000 register address locking.
|
|
*
|
|
* The DM9000 uses an address register to control where data written
|
|
* to the data register goes. This means that the address register
|
|
* must be preserved over interrupts or similar calls.
|
|
*
|
|
* During interrupt and other critical calls, a spinlock is used to
|
|
* protect the system, but the calls themselves save the address
|
|
* in the address register in case they are interrupting another
|
|
* access to the device.
|
|
*
|
|
* For general accesses a lock is provided so that calls which are
|
|
* allowed to sleep are serialised so that the address register does
|
|
* not need to be saved. This lock also serves to serialise access
|
|
* to the EEPROM and PHY access registers which are shared between
|
|
* these two devices.
|
|
*/
|
|
|
|
/* The driver supports the original DM9000E, and now the two newer
|
|
* devices, DM9000A and DM9000B.
|
|
*/
|
|
|
|
enum dm9000_type {
|
|
TYPE_DM9000E, /* original DM9000 */
|
|
TYPE_DM9000A,
|
|
TYPE_DM9000B
|
|
};
|
|
|
|
/* Structure/enum declaration ------------------------------- */
|
|
struct board_info {
|
|
|
|
void __iomem *io_addr; /* Register I/O base address */
|
|
void __iomem *io_data; /* Data I/O address */
|
|
u16 irq; /* IRQ */
|
|
|
|
u16 tx_pkt_cnt;
|
|
u16 queue_pkt_len;
|
|
u16 queue_start_addr;
|
|
u16 queue_ip_summed;
|
|
u16 dbug_cnt;
|
|
u8 io_mode; /* 0:word, 2:byte */
|
|
u8 phy_addr;
|
|
u8 imr_all;
|
|
|
|
unsigned int flags;
|
|
unsigned int in_timeout:1;
|
|
unsigned int in_suspend:1;
|
|
unsigned int wake_supported:1;
|
|
|
|
enum dm9000_type type;
|
|
|
|
void (*inblk)(void __iomem *port, void *data, int length);
|
|
void (*outblk)(void __iomem *port, void *data, int length);
|
|
void (*dumpblk)(void __iomem *port, int length);
|
|
|
|
struct device *dev; /* parent device */
|
|
|
|
struct resource *addr_res; /* resources found */
|
|
struct resource *data_res;
|
|
struct resource *addr_req; /* resources requested */
|
|
struct resource *data_req;
|
|
|
|
int irq_wake;
|
|
|
|
struct mutex addr_lock; /* phy and eeprom access lock */
|
|
|
|
struct delayed_work phy_poll;
|
|
struct net_device *ndev;
|
|
|
|
spinlock_t lock;
|
|
|
|
struct mii_if_info mii;
|
|
u32 msg_enable;
|
|
u32 wake_state;
|
|
|
|
int ip_summed;
|
|
|
|
struct regulator *power_supply;
|
|
};
|
|
|
|
/* debug code */
|
|
|
|
#define dm9000_dbg(db, lev, msg...) do { \
|
|
if ((lev) < debug) { \
|
|
dev_dbg(db->dev, msg); \
|
|
} \
|
|
} while (0)
|
|
|
|
static inline struct board_info *to_dm9000_board(struct net_device *dev)
|
|
{
|
|
return netdev_priv(dev);
|
|
}
|
|
|
|
/* DM9000 network board routine ---------------------------- */
|
|
|
|
/*
|
|
* Read a byte from I/O port
|
|
*/
|
|
static u8
|
|
ior(struct board_info *db, int reg)
|
|
{
|
|
writeb(reg, db->io_addr);
|
|
return readb(db->io_data);
|
|
}
|
|
|
|
/*
|
|
* Write a byte to I/O port
|
|
*/
|
|
|
|
static void
|
|
iow(struct board_info *db, int reg, int value)
|
|
{
|
|
writeb(reg, db->io_addr);
|
|
writeb(value, db->io_data);
|
|
}
|
|
|
|
static void
|
|
dm9000_reset(struct board_info *db)
|
|
{
|
|
dev_dbg(db->dev, "resetting device\n");
|
|
|
|
/* Reset DM9000, see DM9000 Application Notes V1.22 Jun 11, 2004 page 29
|
|
* The essential point is that we have to do a double reset, and the
|
|
* instruction is to set LBK into MAC internal loopback mode.
|
|
*/
|
|
iow(db, DM9000_NCR, NCR_RST | NCR_MAC_LBK);
|
|
udelay(100); /* Application note says at least 20 us */
|
|
if (ior(db, DM9000_NCR) & 1)
|
|
dev_err(db->dev, "dm9000 did not respond to first reset\n");
|
|
|
|
iow(db, DM9000_NCR, 0);
|
|
iow(db, DM9000_NCR, NCR_RST | NCR_MAC_LBK);
|
|
udelay(100);
|
|
if (ior(db, DM9000_NCR) & 1)
|
|
dev_err(db->dev, "dm9000 did not respond to second reset\n");
|
|
}
|
|
|
|
/* routines for sending block to chip */
|
|
|
|
static void dm9000_outblk_8bit(void __iomem *reg, void *data, int count)
|
|
{
|
|
iowrite8_rep(reg, data, count);
|
|
}
|
|
|
|
static void dm9000_outblk_16bit(void __iomem *reg, void *data, int count)
|
|
{
|
|
iowrite16_rep(reg, data, (count+1) >> 1);
|
|
}
|
|
|
|
static void dm9000_outblk_32bit(void __iomem *reg, void *data, int count)
|
|
{
|
|
iowrite32_rep(reg, data, (count+3) >> 2);
|
|
}
|
|
|
|
/* input block from chip to memory */
|
|
|
|
static void dm9000_inblk_8bit(void __iomem *reg, void *data, int count)
|
|
{
|
|
ioread8_rep(reg, data, count);
|
|
}
|
|
|
|
|
|
static void dm9000_inblk_16bit(void __iomem *reg, void *data, int count)
|
|
{
|
|
ioread16_rep(reg, data, (count+1) >> 1);
|
|
}
|
|
|
|
static void dm9000_inblk_32bit(void __iomem *reg, void *data, int count)
|
|
{
|
|
ioread32_rep(reg, data, (count+3) >> 2);
|
|
}
|
|
|
|
/* dump block from chip to null */
|
|
|
|
static void dm9000_dumpblk_8bit(void __iomem *reg, int count)
|
|
{
|
|
int i;
|
|
|
|
for (i = 0; i < count; i++)
|
|
readb(reg);
|
|
}
|
|
|
|
static void dm9000_dumpblk_16bit(void __iomem *reg, int count)
|
|
{
|
|
int i;
|
|
|
|
count = (count + 1) >> 1;
|
|
|
|
for (i = 0; i < count; i++)
|
|
readw(reg);
|
|
}
|
|
|
|
static void dm9000_dumpblk_32bit(void __iomem *reg, int count)
|
|
{
|
|
int i;
|
|
|
|
count = (count + 3) >> 2;
|
|
|
|
for (i = 0; i < count; i++)
|
|
readl(reg);
|
|
}
|
|
|
|
/*
|
|
* Sleep, either by using msleep() or if we are suspending, then
|
|
* use mdelay() to sleep.
|
|
*/
|
|
static void dm9000_msleep(struct board_info *db, unsigned int ms)
|
|
{
|
|
if (db->in_suspend || db->in_timeout)
|
|
mdelay(ms);
|
|
else
|
|
msleep(ms);
|
|
}
|
|
|
|
/* Read a word from phyxcer */
|
|
static int
|
|
dm9000_phy_read(struct net_device *dev, int phy_reg_unused, int reg)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
unsigned long flags;
|
|
unsigned int reg_save;
|
|
int ret;
|
|
|
|
mutex_lock(&db->addr_lock);
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
|
|
/* Save previous register address */
|
|
reg_save = readb(db->io_addr);
|
|
|
|
/* Fill the phyxcer register into REG_0C */
|
|
iow(db, DM9000_EPAR, DM9000_PHY | reg);
|
|
|
|
/* Issue phyxcer read command */
|
|
iow(db, DM9000_EPCR, EPCR_ERPRR | EPCR_EPOS);
|
|
|
|
writeb(reg_save, db->io_addr);
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
dm9000_msleep(db, 1); /* Wait read complete */
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
reg_save = readb(db->io_addr);
|
|
|
|
iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer read command */
|
|
|
|
/* The read data keeps on REG_0D & REG_0E */
|
|
ret = (ior(db, DM9000_EPDRH) << 8) | ior(db, DM9000_EPDRL);
|
|
|
|
/* restore the previous address */
|
|
writeb(reg_save, db->io_addr);
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
mutex_unlock(&db->addr_lock);
|
|
|
|
dm9000_dbg(db, 5, "phy_read[%02x] -> %04x\n", reg, ret);
|
|
return ret;
|
|
}
|
|
|
|
/* Write a word to phyxcer */
|
|
static void
|
|
dm9000_phy_write(struct net_device *dev,
|
|
int phyaddr_unused, int reg, int value)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
unsigned long flags;
|
|
unsigned long reg_save;
|
|
|
|
dm9000_dbg(db, 5, "phy_write[%02x] = %04x\n", reg, value);
|
|
if (!db->in_timeout)
|
|
mutex_lock(&db->addr_lock);
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
|
|
/* Save previous register address */
|
|
reg_save = readb(db->io_addr);
|
|
|
|
/* Fill the phyxcer register into REG_0C */
|
|
iow(db, DM9000_EPAR, DM9000_PHY | reg);
|
|
|
|
/* Fill the written data into REG_0D & REG_0E */
|
|
iow(db, DM9000_EPDRL, value);
|
|
iow(db, DM9000_EPDRH, value >> 8);
|
|
|
|
/* Issue phyxcer write command */
|
|
iow(db, DM9000_EPCR, EPCR_EPOS | EPCR_ERPRW);
|
|
|
|
writeb(reg_save, db->io_addr);
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
dm9000_msleep(db, 1); /* Wait write complete */
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
reg_save = readb(db->io_addr);
|
|
|
|
iow(db, DM9000_EPCR, 0x0); /* Clear phyxcer write command */
|
|
|
|
/* restore the previous address */
|
|
writeb(reg_save, db->io_addr);
|
|
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
if (!db->in_timeout)
|
|
mutex_unlock(&db->addr_lock);
|
|
}
|
|
|
|
/* dm9000_set_io
|
|
*
|
|
* select the specified set of io routines to use with the
|
|
* device
|
|
*/
|
|
|
|
static void dm9000_set_io(struct board_info *db, int byte_width)
|
|
{
|
|
/* use the size of the data resource to work out what IO
|
|
* routines we want to use
|
|
*/
|
|
|
|
switch (byte_width) {
|
|
case 1:
|
|
db->dumpblk = dm9000_dumpblk_8bit;
|
|
db->outblk = dm9000_outblk_8bit;
|
|
db->inblk = dm9000_inblk_8bit;
|
|
break;
|
|
|
|
|
|
case 3:
|
|
dev_dbg(db->dev, ": 3 byte IO, falling back to 16bit\n");
|
|
fallthrough;
|
|
case 2:
|
|
db->dumpblk = dm9000_dumpblk_16bit;
|
|
db->outblk = dm9000_outblk_16bit;
|
|
db->inblk = dm9000_inblk_16bit;
|
|
break;
|
|
|
|
case 4:
|
|
default:
|
|
db->dumpblk = dm9000_dumpblk_32bit;
|
|
db->outblk = dm9000_outblk_32bit;
|
|
db->inblk = dm9000_inblk_32bit;
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void dm9000_schedule_poll(struct board_info *db)
|
|
{
|
|
if (db->type == TYPE_DM9000E)
|
|
schedule_delayed_work(&db->phy_poll, HZ * 2);
|
|
}
|
|
|
|
static int dm9000_ioctl(struct net_device *dev, struct ifreq *req, int cmd)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
|
|
if (!netif_running(dev))
|
|
return -EINVAL;
|
|
|
|
return generic_mii_ioctl(&dm->mii, if_mii(req), cmd, NULL);
|
|
}
|
|
|
|
static unsigned int
|
|
dm9000_read_locked(struct board_info *db, int reg)
|
|
{
|
|
unsigned long flags;
|
|
unsigned int ret;
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
ret = ior(db, reg);
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int dm9000_wait_eeprom(struct board_info *db)
|
|
{
|
|
unsigned int status;
|
|
int timeout = 8; /* wait max 8msec */
|
|
|
|
/* The DM9000 data sheets say we should be able to
|
|
* poll the ERRE bit in EPCR to wait for the EEPROM
|
|
* operation. From testing several chips, this bit
|
|
* does not seem to work.
|
|
*
|
|
* We attempt to use the bit, but fall back to the
|
|
* timeout (which is why we do not return an error
|
|
* on expiry) to say that the EEPROM operation has
|
|
* completed.
|
|
*/
|
|
|
|
while (1) {
|
|
status = dm9000_read_locked(db, DM9000_EPCR);
|
|
|
|
if ((status & EPCR_ERRE) == 0)
|
|
break;
|
|
|
|
msleep(1);
|
|
|
|
if (timeout-- < 0) {
|
|
dev_dbg(db->dev, "timeout waiting EEPROM\n");
|
|
break;
|
|
}
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
/*
|
|
* Read a word data from EEPROM
|
|
*/
|
|
static void
|
|
dm9000_read_eeprom(struct board_info *db, int offset, u8 *to)
|
|
{
|
|
unsigned long flags;
|
|
|
|
if (db->flags & DM9000_PLATF_NO_EEPROM) {
|
|
to[0] = 0xff;
|
|
to[1] = 0xff;
|
|
return;
|
|
}
|
|
|
|
mutex_lock(&db->addr_lock);
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
|
|
iow(db, DM9000_EPAR, offset);
|
|
iow(db, DM9000_EPCR, EPCR_ERPRR);
|
|
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
dm9000_wait_eeprom(db);
|
|
|
|
/* delay for at-least 150uS */
|
|
msleep(1);
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
|
|
iow(db, DM9000_EPCR, 0x0);
|
|
|
|
to[0] = ior(db, DM9000_EPDRL);
|
|
to[1] = ior(db, DM9000_EPDRH);
|
|
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
mutex_unlock(&db->addr_lock);
|
|
}
|
|
|
|
/*
|
|
* Write a word data to SROM
|
|
*/
|
|
static void
|
|
dm9000_write_eeprom(struct board_info *db, int offset, u8 *data)
|
|
{
|
|
unsigned long flags;
|
|
|
|
if (db->flags & DM9000_PLATF_NO_EEPROM)
|
|
return;
|
|
|
|
mutex_lock(&db->addr_lock);
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
iow(db, DM9000_EPAR, offset);
|
|
iow(db, DM9000_EPDRH, data[1]);
|
|
iow(db, DM9000_EPDRL, data[0]);
|
|
iow(db, DM9000_EPCR, EPCR_WEP | EPCR_ERPRW);
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
dm9000_wait_eeprom(db);
|
|
|
|
mdelay(1); /* wait at least 150uS to clear */
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
iow(db, DM9000_EPCR, 0);
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
mutex_unlock(&db->addr_lock);
|
|
}
|
|
|
|
/* ethtool ops */
|
|
|
|
static void dm9000_get_drvinfo(struct net_device *dev,
|
|
struct ethtool_drvinfo *info)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
|
|
strscpy(info->driver, CARDNAME, sizeof(info->driver));
|
|
strscpy(info->bus_info, to_platform_device(dm->dev)->name,
|
|
sizeof(info->bus_info));
|
|
}
|
|
|
|
static u32 dm9000_get_msglevel(struct net_device *dev)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
|
|
return dm->msg_enable;
|
|
}
|
|
|
|
static void dm9000_set_msglevel(struct net_device *dev, u32 value)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
|
|
dm->msg_enable = value;
|
|
}
|
|
|
|
static int dm9000_get_link_ksettings(struct net_device *dev,
|
|
struct ethtool_link_ksettings *cmd)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
|
|
mii_ethtool_get_link_ksettings(&dm->mii, cmd);
|
|
return 0;
|
|
}
|
|
|
|
static int dm9000_set_link_ksettings(struct net_device *dev,
|
|
const struct ethtool_link_ksettings *cmd)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
|
|
return mii_ethtool_set_link_ksettings(&dm->mii, cmd);
|
|
}
|
|
|
|
static int dm9000_nway_reset(struct net_device *dev)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
return mii_nway_restart(&dm->mii);
|
|
}
|
|
|
|
static int dm9000_set_features(struct net_device *dev,
|
|
netdev_features_t features)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
netdev_features_t changed = dev->features ^ features;
|
|
unsigned long flags;
|
|
|
|
if (!(changed & NETIF_F_RXCSUM))
|
|
return 0;
|
|
|
|
spin_lock_irqsave(&dm->lock, flags);
|
|
iow(dm, DM9000_RCSR, (features & NETIF_F_RXCSUM) ? RCSR_CSUM : 0);
|
|
spin_unlock_irqrestore(&dm->lock, flags);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static u32 dm9000_get_link(struct net_device *dev)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
u32 ret;
|
|
|
|
if (dm->flags & DM9000_PLATF_EXT_PHY)
|
|
ret = mii_link_ok(&dm->mii);
|
|
else
|
|
ret = dm9000_read_locked(dm, DM9000_NSR) & NSR_LINKST ? 1 : 0;
|
|
|
|
return ret;
|
|
}
|
|
|
|
#define DM_EEPROM_MAGIC (0x444D394B)
|
|
|
|
static int dm9000_get_eeprom_len(struct net_device *dev)
|
|
{
|
|
return 128;
|
|
}
|
|
|
|
static int dm9000_get_eeprom(struct net_device *dev,
|
|
struct ethtool_eeprom *ee, u8 *data)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
int offset = ee->offset;
|
|
int len = ee->len;
|
|
int i;
|
|
|
|
/* EEPROM access is aligned to two bytes */
|
|
|
|
if ((len & 1) != 0 || (offset & 1) != 0)
|
|
return -EINVAL;
|
|
|
|
if (dm->flags & DM9000_PLATF_NO_EEPROM)
|
|
return -ENOENT;
|
|
|
|
ee->magic = DM_EEPROM_MAGIC;
|
|
|
|
for (i = 0; i < len; i += 2)
|
|
dm9000_read_eeprom(dm, (offset + i) / 2, data + i);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int dm9000_set_eeprom(struct net_device *dev,
|
|
struct ethtool_eeprom *ee, u8 *data)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
int offset = ee->offset;
|
|
int len = ee->len;
|
|
int done;
|
|
|
|
/* EEPROM access is aligned to two bytes */
|
|
|
|
if (dm->flags & DM9000_PLATF_NO_EEPROM)
|
|
return -ENOENT;
|
|
|
|
if (ee->magic != DM_EEPROM_MAGIC)
|
|
return -EINVAL;
|
|
|
|
while (len > 0) {
|
|
if (len & 1 || offset & 1) {
|
|
int which = offset & 1;
|
|
u8 tmp[2];
|
|
|
|
dm9000_read_eeprom(dm, offset / 2, tmp);
|
|
tmp[which] = *data;
|
|
dm9000_write_eeprom(dm, offset / 2, tmp);
|
|
|
|
done = 1;
|
|
} else {
|
|
dm9000_write_eeprom(dm, offset / 2, data);
|
|
done = 2;
|
|
}
|
|
|
|
data += done;
|
|
offset += done;
|
|
len -= done;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void dm9000_get_wol(struct net_device *dev, struct ethtool_wolinfo *w)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
|
|
memset(w, 0, sizeof(struct ethtool_wolinfo));
|
|
|
|
/* note, we could probably support wake-phy too */
|
|
w->supported = dm->wake_supported ? WAKE_MAGIC : 0;
|
|
w->wolopts = dm->wake_state;
|
|
}
|
|
|
|
static int dm9000_set_wol(struct net_device *dev, struct ethtool_wolinfo *w)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
unsigned long flags;
|
|
u32 opts = w->wolopts;
|
|
u32 wcr = 0;
|
|
|
|
if (!dm->wake_supported)
|
|
return -EOPNOTSUPP;
|
|
|
|
if (opts & ~WAKE_MAGIC)
|
|
return -EINVAL;
|
|
|
|
if (opts & WAKE_MAGIC)
|
|
wcr |= WCR_MAGICEN;
|
|
|
|
mutex_lock(&dm->addr_lock);
|
|
|
|
spin_lock_irqsave(&dm->lock, flags);
|
|
iow(dm, DM9000_WCR, wcr);
|
|
spin_unlock_irqrestore(&dm->lock, flags);
|
|
|
|
mutex_unlock(&dm->addr_lock);
|
|
|
|
if (dm->wake_state != opts) {
|
|
/* change in wol state, update IRQ state */
|
|
|
|
if (!dm->wake_state)
|
|
irq_set_irq_wake(dm->irq_wake, 1);
|
|
else if (dm->wake_state && !opts)
|
|
irq_set_irq_wake(dm->irq_wake, 0);
|
|
}
|
|
|
|
dm->wake_state = opts;
|
|
return 0;
|
|
}
|
|
|
|
static const struct ethtool_ops dm9000_ethtool_ops = {
|
|
.get_drvinfo = dm9000_get_drvinfo,
|
|
.get_msglevel = dm9000_get_msglevel,
|
|
.set_msglevel = dm9000_set_msglevel,
|
|
.nway_reset = dm9000_nway_reset,
|
|
.get_link = dm9000_get_link,
|
|
.get_wol = dm9000_get_wol,
|
|
.set_wol = dm9000_set_wol,
|
|
.get_eeprom_len = dm9000_get_eeprom_len,
|
|
.get_eeprom = dm9000_get_eeprom,
|
|
.set_eeprom = dm9000_set_eeprom,
|
|
.get_link_ksettings = dm9000_get_link_ksettings,
|
|
.set_link_ksettings = dm9000_set_link_ksettings,
|
|
};
|
|
|
|
static void dm9000_show_carrier(struct board_info *db,
|
|
unsigned carrier, unsigned nsr)
|
|
{
|
|
int lpa;
|
|
struct net_device *ndev = db->ndev;
|
|
struct mii_if_info *mii = &db->mii;
|
|
unsigned ncr = dm9000_read_locked(db, DM9000_NCR);
|
|
|
|
if (carrier) {
|
|
lpa = mii->mdio_read(mii->dev, mii->phy_id, MII_LPA);
|
|
dev_info(db->dev,
|
|
"%s: link up, %dMbps, %s-duplex, lpa 0x%04X\n",
|
|
ndev->name, (nsr & NSR_SPEED) ? 10 : 100,
|
|
(ncr & NCR_FDX) ? "full" : "half", lpa);
|
|
} else {
|
|
dev_info(db->dev, "%s: link down\n", ndev->name);
|
|
}
|
|
}
|
|
|
|
static void
|
|
dm9000_poll_work(struct work_struct *w)
|
|
{
|
|
struct delayed_work *dw = to_delayed_work(w);
|
|
struct board_info *db = container_of(dw, struct board_info, phy_poll);
|
|
struct net_device *ndev = db->ndev;
|
|
|
|
if (db->flags & DM9000_PLATF_SIMPLE_PHY &&
|
|
!(db->flags & DM9000_PLATF_EXT_PHY)) {
|
|
unsigned nsr = dm9000_read_locked(db, DM9000_NSR);
|
|
unsigned old_carrier = netif_carrier_ok(ndev) ? 1 : 0;
|
|
unsigned new_carrier;
|
|
|
|
new_carrier = (nsr & NSR_LINKST) ? 1 : 0;
|
|
|
|
if (old_carrier != new_carrier) {
|
|
if (netif_msg_link(db))
|
|
dm9000_show_carrier(db, new_carrier, nsr);
|
|
|
|
if (!new_carrier)
|
|
netif_carrier_off(ndev);
|
|
else
|
|
netif_carrier_on(ndev);
|
|
}
|
|
} else
|
|
mii_check_media(&db->mii, netif_msg_link(db), 0);
|
|
|
|
if (netif_running(ndev))
|
|
dm9000_schedule_poll(db);
|
|
}
|
|
|
|
/* dm9000_release_board
|
|
*
|
|
* release a board, and any mapped resources
|
|
*/
|
|
|
|
static void
|
|
dm9000_release_board(struct platform_device *pdev, struct board_info *db)
|
|
{
|
|
/* unmap our resources */
|
|
|
|
iounmap(db->io_addr);
|
|
iounmap(db->io_data);
|
|
|
|
/* release the resources */
|
|
|
|
if (db->data_req)
|
|
release_resource(db->data_req);
|
|
kfree(db->data_req);
|
|
|
|
if (db->addr_req)
|
|
release_resource(db->addr_req);
|
|
kfree(db->addr_req);
|
|
}
|
|
|
|
static unsigned char dm9000_type_to_char(enum dm9000_type type)
|
|
{
|
|
switch (type) {
|
|
case TYPE_DM9000E: return 'e';
|
|
case TYPE_DM9000A: return 'a';
|
|
case TYPE_DM9000B: return 'b';
|
|
}
|
|
|
|
return '?';
|
|
}
|
|
|
|
/*
|
|
* Set DM9000 multicast address
|
|
*/
|
|
static void
|
|
dm9000_hash_table_unlocked(struct net_device *dev)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
struct netdev_hw_addr *ha;
|
|
int i, oft;
|
|
u32 hash_val;
|
|
u16 hash_table[4] = { 0, 0, 0, 0x8000 }; /* broadcast address */
|
|
u8 rcr = RCR_DIS_LONG | RCR_DIS_CRC | RCR_RXEN;
|
|
|
|
dm9000_dbg(db, 1, "entering %s\n", __func__);
|
|
|
|
for (i = 0, oft = DM9000_PAR; i < 6; i++, oft++)
|
|
iow(db, oft, dev->dev_addr[i]);
|
|
|
|
if (dev->flags & IFF_PROMISC)
|
|
rcr |= RCR_PRMSC;
|
|
|
|
if (dev->flags & IFF_ALLMULTI)
|
|
rcr |= RCR_ALL;
|
|
|
|
/* the multicast address in Hash Table : 64 bits */
|
|
netdev_for_each_mc_addr(ha, dev) {
|
|
hash_val = ether_crc_le(6, ha->addr) & 0x3f;
|
|
hash_table[hash_val / 16] |= (u16) 1 << (hash_val % 16);
|
|
}
|
|
|
|
/* Write the hash table to MAC MD table */
|
|
for (i = 0, oft = DM9000_MAR; i < 4; i++) {
|
|
iow(db, oft++, hash_table[i]);
|
|
iow(db, oft++, hash_table[i] >> 8);
|
|
}
|
|
|
|
iow(db, DM9000_RCR, rcr);
|
|
}
|
|
|
|
static void
|
|
dm9000_hash_table(struct net_device *dev)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
unsigned long flags;
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
dm9000_hash_table_unlocked(dev);
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
}
|
|
|
|
static void
|
|
dm9000_mask_interrupts(struct board_info *db)
|
|
{
|
|
iow(db, DM9000_IMR, IMR_PAR);
|
|
}
|
|
|
|
static void
|
|
dm9000_unmask_interrupts(struct board_info *db)
|
|
{
|
|
iow(db, DM9000_IMR, db->imr_all);
|
|
}
|
|
|
|
/*
|
|
* Initialize dm9000 board
|
|
*/
|
|
static void
|
|
dm9000_init_dm9000(struct net_device *dev)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
unsigned int imr;
|
|
unsigned int ncr;
|
|
|
|
dm9000_dbg(db, 1, "entering %s\n", __func__);
|
|
|
|
dm9000_reset(db);
|
|
dm9000_mask_interrupts(db);
|
|
|
|
/* I/O mode */
|
|
db->io_mode = ior(db, DM9000_ISR) >> 6; /* ISR bit7:6 keeps I/O mode */
|
|
|
|
/* Checksum mode */
|
|
if (dev->hw_features & NETIF_F_RXCSUM)
|
|
iow(db, DM9000_RCSR,
|
|
(dev->features & NETIF_F_RXCSUM) ? RCSR_CSUM : 0);
|
|
|
|
iow(db, DM9000_GPCR, GPCR_GEP_CNTL); /* Let GPIO0 output */
|
|
iow(db, DM9000_GPR, 0);
|
|
|
|
/* If we are dealing with DM9000B, some extra steps are required: a
|
|
* manual phy reset, and setting init params.
|
|
*/
|
|
if (db->type == TYPE_DM9000B) {
|
|
dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET);
|
|
dm9000_phy_write(dev, 0, MII_DM_DSPCR, DSPCR_INIT_PARAM);
|
|
}
|
|
|
|
ncr = (db->flags & DM9000_PLATF_EXT_PHY) ? NCR_EXT_PHY : 0;
|
|
|
|
/* if wol is needed, then always set NCR_WAKEEN otherwise we end
|
|
* up dumping the wake events if we disable this. There is already
|
|
* a wake-mask in DM9000_WCR */
|
|
if (db->wake_supported)
|
|
ncr |= NCR_WAKEEN;
|
|
|
|
iow(db, DM9000_NCR, ncr);
|
|
|
|
/* Program operating register */
|
|
iow(db, DM9000_TCR, 0); /* TX Polling clear */
|
|
iow(db, DM9000_BPTR, 0x3f); /* Less 3Kb, 200us */
|
|
iow(db, DM9000_FCR, 0xff); /* Flow Control */
|
|
iow(db, DM9000_SMCR, 0); /* Special Mode */
|
|
/* clear TX status */
|
|
iow(db, DM9000_NSR, NSR_WAKEST | NSR_TX2END | NSR_TX1END);
|
|
iow(db, DM9000_ISR, ISR_CLR_STATUS); /* Clear interrupt status */
|
|
|
|
/* Set address filter table */
|
|
dm9000_hash_table_unlocked(dev);
|
|
|
|
imr = IMR_PAR | IMR_PTM | IMR_PRM;
|
|
if (db->type != TYPE_DM9000E)
|
|
imr |= IMR_LNKCHNG;
|
|
|
|
db->imr_all = imr;
|
|
|
|
/* Init Driver variable */
|
|
db->tx_pkt_cnt = 0;
|
|
db->queue_pkt_len = 0;
|
|
netif_trans_update(dev);
|
|
}
|
|
|
|
/* Our watchdog timed out. Called by the networking layer */
|
|
static void dm9000_timeout(struct net_device *dev, unsigned int txqueue)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
u8 reg_save;
|
|
unsigned long flags;
|
|
|
|
/* Save previous register address */
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
db->in_timeout = 1;
|
|
reg_save = readb(db->io_addr);
|
|
|
|
netif_stop_queue(dev);
|
|
dm9000_init_dm9000(dev);
|
|
dm9000_unmask_interrupts(db);
|
|
/* We can accept TX packets again */
|
|
netif_trans_update(dev); /* prevent tx timeout */
|
|
netif_wake_queue(dev);
|
|
|
|
/* Restore previous register address */
|
|
writeb(reg_save, db->io_addr);
|
|
db->in_timeout = 0;
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
}
|
|
|
|
static void dm9000_send_packet(struct net_device *dev,
|
|
int ip_summed,
|
|
u16 pkt_len)
|
|
{
|
|
struct board_info *dm = to_dm9000_board(dev);
|
|
|
|
/* The DM9000 is not smart enough to leave fragmented packets alone. */
|
|
if (dm->ip_summed != ip_summed) {
|
|
if (ip_summed == CHECKSUM_NONE)
|
|
iow(dm, DM9000_TCCR, 0);
|
|
else
|
|
iow(dm, DM9000_TCCR, TCCR_IP | TCCR_UDP | TCCR_TCP);
|
|
dm->ip_summed = ip_summed;
|
|
}
|
|
|
|
/* Set TX length to DM9000 */
|
|
iow(dm, DM9000_TXPLL, pkt_len);
|
|
iow(dm, DM9000_TXPLH, pkt_len >> 8);
|
|
|
|
/* Issue TX polling command */
|
|
iow(dm, DM9000_TCR, TCR_TXREQ); /* Cleared after TX complete */
|
|
}
|
|
|
|
/*
|
|
* Hardware start transmission.
|
|
* Send a packet to media from the upper layer.
|
|
*/
|
|
static netdev_tx_t
|
|
dm9000_start_xmit(struct sk_buff *skb, struct net_device *dev)
|
|
{
|
|
unsigned long flags;
|
|
struct board_info *db = netdev_priv(dev);
|
|
|
|
dm9000_dbg(db, 3, "%s:\n", __func__);
|
|
|
|
if (db->tx_pkt_cnt > 1)
|
|
return NETDEV_TX_BUSY;
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
|
|
/* Move data to DM9000 TX RAM */
|
|
writeb(DM9000_MWCMD, db->io_addr);
|
|
|
|
(db->outblk)(db->io_data, skb->data, skb->len);
|
|
dev->stats.tx_bytes += skb->len;
|
|
|
|
db->tx_pkt_cnt++;
|
|
/* TX control: First packet immediately send, second packet queue */
|
|
if (db->tx_pkt_cnt == 1) {
|
|
dm9000_send_packet(dev, skb->ip_summed, skb->len);
|
|
} else {
|
|
/* Second packet */
|
|
db->queue_pkt_len = skb->len;
|
|
db->queue_ip_summed = skb->ip_summed;
|
|
netif_stop_queue(dev);
|
|
}
|
|
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
/* free this SKB */
|
|
dev_consume_skb_any(skb);
|
|
|
|
return NETDEV_TX_OK;
|
|
}
|
|
|
|
/*
|
|
* DM9000 interrupt handler
|
|
* receive the packet to upper layer, free the transmitted packet
|
|
*/
|
|
|
|
static void dm9000_tx_done(struct net_device *dev, struct board_info *db)
|
|
{
|
|
int tx_status = ior(db, DM9000_NSR); /* Got TX status */
|
|
|
|
if (tx_status & (NSR_TX2END | NSR_TX1END)) {
|
|
/* One packet sent complete */
|
|
db->tx_pkt_cnt--;
|
|
dev->stats.tx_packets++;
|
|
|
|
if (netif_msg_tx_done(db))
|
|
dev_dbg(db->dev, "tx done, NSR %02x\n", tx_status);
|
|
|
|
/* Queue packet check & send */
|
|
if (db->tx_pkt_cnt > 0)
|
|
dm9000_send_packet(dev, db->queue_ip_summed,
|
|
db->queue_pkt_len);
|
|
netif_wake_queue(dev);
|
|
}
|
|
}
|
|
|
|
struct dm9000_rxhdr {
|
|
u8 RxPktReady;
|
|
u8 RxStatus;
|
|
__le16 RxLen;
|
|
} __packed;
|
|
|
|
/*
|
|
* Received a packet and pass to upper layer
|
|
*/
|
|
static void
|
|
dm9000_rx(struct net_device *dev)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
struct dm9000_rxhdr rxhdr;
|
|
struct sk_buff *skb;
|
|
u8 rxbyte, *rdptr;
|
|
bool GoodPacket;
|
|
int RxLen;
|
|
|
|
/* Check packet ready or not */
|
|
do {
|
|
ior(db, DM9000_MRCMDX); /* Dummy read */
|
|
|
|
/* Get most updated data */
|
|
rxbyte = readb(db->io_data);
|
|
|
|
/* Status check: this byte must be 0 or 1 */
|
|
if (rxbyte & DM9000_PKT_ERR) {
|
|
dev_warn(db->dev, "status check fail: %d\n", rxbyte);
|
|
iow(db, DM9000_RCR, 0x00); /* Stop Device */
|
|
return;
|
|
}
|
|
|
|
if (!(rxbyte & DM9000_PKT_RDY))
|
|
return;
|
|
|
|
/* A packet ready now & Get status/length */
|
|
GoodPacket = true;
|
|
writeb(DM9000_MRCMD, db->io_addr);
|
|
|
|
(db->inblk)(db->io_data, &rxhdr, sizeof(rxhdr));
|
|
|
|
RxLen = le16_to_cpu(rxhdr.RxLen);
|
|
|
|
if (netif_msg_rx_status(db))
|
|
dev_dbg(db->dev, "RX: status %02x, length %04x\n",
|
|
rxhdr.RxStatus, RxLen);
|
|
|
|
/* Packet Status check */
|
|
if (RxLen < 0x40) {
|
|
GoodPacket = false;
|
|
if (netif_msg_rx_err(db))
|
|
dev_dbg(db->dev, "RX: Bad Packet (runt)\n");
|
|
}
|
|
|
|
if (RxLen > DM9000_PKT_MAX) {
|
|
dev_dbg(db->dev, "RST: RX Len:%x\n", RxLen);
|
|
}
|
|
|
|
/* rxhdr.RxStatus is identical to RSR register. */
|
|
if (rxhdr.RxStatus & (RSR_FOE | RSR_CE | RSR_AE |
|
|
RSR_PLE | RSR_RWTO |
|
|
RSR_LCS | RSR_RF)) {
|
|
GoodPacket = false;
|
|
if (rxhdr.RxStatus & RSR_FOE) {
|
|
if (netif_msg_rx_err(db))
|
|
dev_dbg(db->dev, "fifo error\n");
|
|
dev->stats.rx_fifo_errors++;
|
|
}
|
|
if (rxhdr.RxStatus & RSR_CE) {
|
|
if (netif_msg_rx_err(db))
|
|
dev_dbg(db->dev, "crc error\n");
|
|
dev->stats.rx_crc_errors++;
|
|
}
|
|
if (rxhdr.RxStatus & RSR_RF) {
|
|
if (netif_msg_rx_err(db))
|
|
dev_dbg(db->dev, "length error\n");
|
|
dev->stats.rx_length_errors++;
|
|
}
|
|
}
|
|
|
|
/* Move data from DM9000 */
|
|
if (GoodPacket &&
|
|
((skb = netdev_alloc_skb(dev, RxLen + 4)) != NULL)) {
|
|
skb_reserve(skb, 2);
|
|
rdptr = skb_put(skb, RxLen - 4);
|
|
|
|
/* Read received packet from RX SRAM */
|
|
|
|
(db->inblk)(db->io_data, rdptr, RxLen);
|
|
dev->stats.rx_bytes += RxLen;
|
|
|
|
/* Pass to upper layer */
|
|
skb->protocol = eth_type_trans(skb, dev);
|
|
if (dev->features & NETIF_F_RXCSUM) {
|
|
if ((((rxbyte & 0x1c) << 3) & rxbyte) == 0)
|
|
skb->ip_summed = CHECKSUM_UNNECESSARY;
|
|
else
|
|
skb_checksum_none_assert(skb);
|
|
}
|
|
netif_rx(skb);
|
|
dev->stats.rx_packets++;
|
|
|
|
} else {
|
|
/* need to dump the packet's data */
|
|
|
|
(db->dumpblk)(db->io_data, RxLen);
|
|
}
|
|
} while (rxbyte & DM9000_PKT_RDY);
|
|
}
|
|
|
|
static irqreturn_t dm9000_interrupt(int irq, void *dev_id)
|
|
{
|
|
struct net_device *dev = dev_id;
|
|
struct board_info *db = netdev_priv(dev);
|
|
int int_status;
|
|
unsigned long flags;
|
|
u8 reg_save;
|
|
|
|
dm9000_dbg(db, 3, "entering %s\n", __func__);
|
|
|
|
/* A real interrupt coming */
|
|
|
|
/* holders of db->lock must always block IRQs */
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
|
|
/* Save previous register address */
|
|
reg_save = readb(db->io_addr);
|
|
|
|
dm9000_mask_interrupts(db);
|
|
/* Got DM9000 interrupt status */
|
|
int_status = ior(db, DM9000_ISR); /* Got ISR */
|
|
iow(db, DM9000_ISR, int_status); /* Clear ISR status */
|
|
|
|
if (netif_msg_intr(db))
|
|
dev_dbg(db->dev, "interrupt status %02x\n", int_status);
|
|
|
|
/* Received the coming packet */
|
|
if (int_status & ISR_PRS)
|
|
dm9000_rx(dev);
|
|
|
|
/* Transmit Interrupt check */
|
|
if (int_status & ISR_PTS)
|
|
dm9000_tx_done(dev, db);
|
|
|
|
if (db->type != TYPE_DM9000E) {
|
|
if (int_status & ISR_LNKCHNG) {
|
|
/* fire a link-change request */
|
|
schedule_delayed_work(&db->phy_poll, 1);
|
|
}
|
|
}
|
|
|
|
dm9000_unmask_interrupts(db);
|
|
/* Restore previous register address */
|
|
writeb(reg_save, db->io_addr);
|
|
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static irqreturn_t dm9000_wol_interrupt(int irq, void *dev_id)
|
|
{
|
|
struct net_device *dev = dev_id;
|
|
struct board_info *db = netdev_priv(dev);
|
|
unsigned long flags;
|
|
unsigned nsr, wcr;
|
|
|
|
spin_lock_irqsave(&db->lock, flags);
|
|
|
|
nsr = ior(db, DM9000_NSR);
|
|
wcr = ior(db, DM9000_WCR);
|
|
|
|
dev_dbg(db->dev, "%s: NSR=0x%02x, WCR=0x%02x\n", __func__, nsr, wcr);
|
|
|
|
if (nsr & NSR_WAKEST) {
|
|
/* clear, so we can avoid */
|
|
iow(db, DM9000_NSR, NSR_WAKEST);
|
|
|
|
if (wcr & WCR_LINKST)
|
|
dev_info(db->dev, "wake by link status change\n");
|
|
if (wcr & WCR_SAMPLEST)
|
|
dev_info(db->dev, "wake by sample packet\n");
|
|
if (wcr & WCR_MAGICST)
|
|
dev_info(db->dev, "wake by magic packet\n");
|
|
if (!(wcr & (WCR_LINKST | WCR_SAMPLEST | WCR_MAGICST)))
|
|
dev_err(db->dev, "wake signalled with no reason? "
|
|
"NSR=0x%02x, WSR=0x%02x\n", nsr, wcr);
|
|
}
|
|
|
|
spin_unlock_irqrestore(&db->lock, flags);
|
|
|
|
return (nsr & NSR_WAKEST) ? IRQ_HANDLED : IRQ_NONE;
|
|
}
|
|
|
|
#ifdef CONFIG_NET_POLL_CONTROLLER
|
|
/*
|
|
*Used by netconsole
|
|
*/
|
|
static void dm9000_poll_controller(struct net_device *dev)
|
|
{
|
|
disable_irq(dev->irq);
|
|
dm9000_interrupt(dev->irq, dev);
|
|
enable_irq(dev->irq);
|
|
}
|
|
#endif
|
|
|
|
/*
|
|
* Open the interface.
|
|
* The interface is opened whenever "ifconfig" actives it.
|
|
*/
|
|
static int
|
|
dm9000_open(struct net_device *dev)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
unsigned int irq_flags = irq_get_trigger_type(dev->irq);
|
|
|
|
if (netif_msg_ifup(db))
|
|
dev_dbg(db->dev, "enabling %s\n", dev->name);
|
|
|
|
/* If there is no IRQ type specified, tell the user that this is a
|
|
* problem
|
|
*/
|
|
if (irq_flags == IRQF_TRIGGER_NONE)
|
|
dev_warn(db->dev, "WARNING: no IRQ resource flags set.\n");
|
|
|
|
irq_flags |= IRQF_SHARED;
|
|
|
|
/* GPIO0 on pre-activate PHY, Reg 1F is not set by reset */
|
|
iow(db, DM9000_GPR, 0); /* REG_1F bit0 activate phyxcer */
|
|
mdelay(1); /* delay needs by DM9000B */
|
|
|
|
/* Initialize DM9000 board */
|
|
dm9000_init_dm9000(dev);
|
|
|
|
if (request_irq(dev->irq, dm9000_interrupt, irq_flags, dev->name, dev))
|
|
return -EAGAIN;
|
|
/* Now that we have an interrupt handler hooked up we can unmask
|
|
* our interrupts
|
|
*/
|
|
dm9000_unmask_interrupts(db);
|
|
|
|
/* Init driver variable */
|
|
db->dbug_cnt = 0;
|
|
|
|
mii_check_media(&db->mii, netif_msg_link(db), 1);
|
|
netif_start_queue(dev);
|
|
|
|
/* Poll initial link status */
|
|
schedule_delayed_work(&db->phy_poll, 1);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void
|
|
dm9000_shutdown(struct net_device *dev)
|
|
{
|
|
struct board_info *db = netdev_priv(dev);
|
|
|
|
/* RESET device */
|
|
dm9000_phy_write(dev, 0, MII_BMCR, BMCR_RESET); /* PHY RESET */
|
|
iow(db, DM9000_GPR, 0x01); /* Power-Down PHY */
|
|
dm9000_mask_interrupts(db);
|
|
iow(db, DM9000_RCR, 0x00); /* Disable RX */
|
|
}
|
|
|
|
/*
|
|
* Stop the interface.
|
|
* The interface is stopped when it is brought.
|
|
*/
|
|
static int
|
|
dm9000_stop(struct net_device *ndev)
|
|
{
|
|
struct board_info *db = netdev_priv(ndev);
|
|
|
|
if (netif_msg_ifdown(db))
|
|
dev_dbg(db->dev, "shutting down %s\n", ndev->name);
|
|
|
|
cancel_delayed_work_sync(&db->phy_poll);
|
|
|
|
netif_stop_queue(ndev);
|
|
netif_carrier_off(ndev);
|
|
|
|
/* free interrupt */
|
|
free_irq(ndev->irq, ndev);
|
|
|
|
dm9000_shutdown(ndev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct net_device_ops dm9000_netdev_ops = {
|
|
.ndo_open = dm9000_open,
|
|
.ndo_stop = dm9000_stop,
|
|
.ndo_start_xmit = dm9000_start_xmit,
|
|
.ndo_tx_timeout = dm9000_timeout,
|
|
.ndo_set_rx_mode = dm9000_hash_table,
|
|
.ndo_eth_ioctl = dm9000_ioctl,
|
|
.ndo_set_features = dm9000_set_features,
|
|
.ndo_validate_addr = eth_validate_addr,
|
|
.ndo_set_mac_address = eth_mac_addr,
|
|
#ifdef CONFIG_NET_POLL_CONTROLLER
|
|
.ndo_poll_controller = dm9000_poll_controller,
|
|
#endif
|
|
};
|
|
|
|
static struct dm9000_plat_data *dm9000_parse_dt(struct device *dev)
|
|
{
|
|
struct dm9000_plat_data *pdata;
|
|
struct device_node *np = dev->of_node;
|
|
int ret;
|
|
|
|
if (!IS_ENABLED(CONFIG_OF) || !np)
|
|
return ERR_PTR(-ENXIO);
|
|
|
|
pdata = devm_kzalloc(dev, sizeof(*pdata), GFP_KERNEL);
|
|
if (!pdata)
|
|
return ERR_PTR(-ENOMEM);
|
|
|
|
if (of_find_property(np, "davicom,ext-phy", NULL))
|
|
pdata->flags |= DM9000_PLATF_EXT_PHY;
|
|
if (of_find_property(np, "davicom,no-eeprom", NULL))
|
|
pdata->flags |= DM9000_PLATF_NO_EEPROM;
|
|
|
|
ret = of_get_mac_address(np, pdata->dev_addr);
|
|
if (ret == -EPROBE_DEFER)
|
|
return ERR_PTR(ret);
|
|
|
|
return pdata;
|
|
}
|
|
|
|
/*
|
|
* Search DM9000 board, allocate space and register it
|
|
*/
|
|
static int
|
|
dm9000_probe(struct platform_device *pdev)
|
|
{
|
|
struct dm9000_plat_data *pdata = dev_get_platdata(&pdev->dev);
|
|
struct board_info *db; /* Point a board information structure */
|
|
struct net_device *ndev;
|
|
struct device *dev = &pdev->dev;
|
|
const unsigned char *mac_src;
|
|
int ret = 0;
|
|
int iosize;
|
|
int i;
|
|
u32 id_val;
|
|
struct gpio_desc *reset_gpio;
|
|
struct regulator *power;
|
|
bool inv_mac_addr = false;
|
|
u8 addr[ETH_ALEN];
|
|
|
|
power = devm_regulator_get(dev, "vcc");
|
|
if (IS_ERR(power)) {
|
|
if (PTR_ERR(power) == -EPROBE_DEFER)
|
|
return -EPROBE_DEFER;
|
|
dev_dbg(dev, "no regulator provided\n");
|
|
} else {
|
|
ret = regulator_enable(power);
|
|
if (ret != 0) {
|
|
dev_err(dev,
|
|
"Failed to enable power regulator: %d\n", ret);
|
|
return ret;
|
|
}
|
|
dev_dbg(dev, "regulator enabled\n");
|
|
}
|
|
|
|
reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_HIGH);
|
|
ret = PTR_ERR_OR_ZERO(reset_gpio);
|
|
if (ret) {
|
|
dev_err(dev, "failed to request reset gpio: %d\n", ret);
|
|
goto out_regulator_disable;
|
|
}
|
|
|
|
if (reset_gpio) {
|
|
ret = gpiod_set_consumer_name(reset_gpio, "dm9000_reset");
|
|
if (ret) {
|
|
dev_err(dev, "failed to set reset gpio name: %d\n",
|
|
ret);
|
|
goto out_regulator_disable;
|
|
}
|
|
|
|
/* According to manual PWRST# Low Period Min 1ms */
|
|
msleep(2);
|
|
gpiod_set_value_cansleep(reset_gpio, 0);
|
|
/* Needs 3ms to read eeprom when PWRST is deasserted */
|
|
msleep(4);
|
|
}
|
|
|
|
if (!pdata) {
|
|
pdata = dm9000_parse_dt(&pdev->dev);
|
|
if (IS_ERR(pdata)) {
|
|
ret = PTR_ERR(pdata);
|
|
goto out_regulator_disable;
|
|
}
|
|
}
|
|
|
|
/* Init network device */
|
|
ndev = alloc_etherdev(sizeof(struct board_info));
|
|
if (!ndev) {
|
|
ret = -ENOMEM;
|
|
goto out_regulator_disable;
|
|
}
|
|
|
|
SET_NETDEV_DEV(ndev, &pdev->dev);
|
|
|
|
dev_dbg(&pdev->dev, "dm9000_probe()\n");
|
|
|
|
/* setup board info structure */
|
|
db = netdev_priv(ndev);
|
|
|
|
db->dev = &pdev->dev;
|
|
db->ndev = ndev;
|
|
if (!IS_ERR(power))
|
|
db->power_supply = power;
|
|
|
|
spin_lock_init(&db->lock);
|
|
mutex_init(&db->addr_lock);
|
|
|
|
INIT_DELAYED_WORK(&db->phy_poll, dm9000_poll_work);
|
|
|
|
db->addr_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
db->data_res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
|
|
|
|
if (!db->addr_res || !db->data_res) {
|
|
dev_err(db->dev, "insufficient resources addr=%p data=%p\n",
|
|
db->addr_res, db->data_res);
|
|
ret = -ENOENT;
|
|
goto out;
|
|
}
|
|
|
|
ndev->irq = platform_get_irq(pdev, 0);
|
|
if (ndev->irq < 0) {
|
|
ret = ndev->irq;
|
|
goto out;
|
|
}
|
|
|
|
db->irq_wake = platform_get_irq_optional(pdev, 1);
|
|
if (db->irq_wake >= 0) {
|
|
dev_dbg(db->dev, "wakeup irq %d\n", db->irq_wake);
|
|
|
|
ret = request_irq(db->irq_wake, dm9000_wol_interrupt,
|
|
IRQF_SHARED, dev_name(db->dev), ndev);
|
|
if (ret) {
|
|
dev_err(db->dev, "cannot get wakeup irq (%d)\n", ret);
|
|
} else {
|
|
|
|
/* test to see if irq is really wakeup capable */
|
|
ret = irq_set_irq_wake(db->irq_wake, 1);
|
|
if (ret) {
|
|
dev_err(db->dev, "irq %d cannot set wakeup (%d)\n",
|
|
db->irq_wake, ret);
|
|
} else {
|
|
irq_set_irq_wake(db->irq_wake, 0);
|
|
db->wake_supported = 1;
|
|
}
|
|
}
|
|
}
|
|
|
|
iosize = resource_size(db->addr_res);
|
|
db->addr_req = request_mem_region(db->addr_res->start, iosize,
|
|
pdev->name);
|
|
|
|
if (db->addr_req == NULL) {
|
|
dev_err(db->dev, "cannot claim address reg area\n");
|
|
ret = -EIO;
|
|
goto out;
|
|
}
|
|
|
|
db->io_addr = ioremap(db->addr_res->start, iosize);
|
|
|
|
if (db->io_addr == NULL) {
|
|
dev_err(db->dev, "failed to ioremap address reg\n");
|
|
ret = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
iosize = resource_size(db->data_res);
|
|
db->data_req = request_mem_region(db->data_res->start, iosize,
|
|
pdev->name);
|
|
|
|
if (db->data_req == NULL) {
|
|
dev_err(db->dev, "cannot claim data reg area\n");
|
|
ret = -EIO;
|
|
goto out;
|
|
}
|
|
|
|
db->io_data = ioremap(db->data_res->start, iosize);
|
|
|
|
if (db->io_data == NULL) {
|
|
dev_err(db->dev, "failed to ioremap data reg\n");
|
|
ret = -EINVAL;
|
|
goto out;
|
|
}
|
|
|
|
/* fill in parameters for net-dev structure */
|
|
ndev->base_addr = (unsigned long)db->io_addr;
|
|
|
|
/* ensure at least we have a default set of IO routines */
|
|
dm9000_set_io(db, iosize);
|
|
|
|
/* check to see if anything is being over-ridden */
|
|
if (pdata != NULL) {
|
|
/* check to see if the driver wants to over-ride the
|
|
* default IO width */
|
|
|
|
if (pdata->flags & DM9000_PLATF_8BITONLY)
|
|
dm9000_set_io(db, 1);
|
|
|
|
if (pdata->flags & DM9000_PLATF_16BITONLY)
|
|
dm9000_set_io(db, 2);
|
|
|
|
if (pdata->flags & DM9000_PLATF_32BITONLY)
|
|
dm9000_set_io(db, 4);
|
|
|
|
/* check to see if there are any IO routine
|
|
* over-rides */
|
|
|
|
if (pdata->inblk != NULL)
|
|
db->inblk = pdata->inblk;
|
|
|
|
if (pdata->outblk != NULL)
|
|
db->outblk = pdata->outblk;
|
|
|
|
if (pdata->dumpblk != NULL)
|
|
db->dumpblk = pdata->dumpblk;
|
|
|
|
db->flags = pdata->flags;
|
|
}
|
|
|
|
#ifdef CONFIG_DM9000_FORCE_SIMPLE_PHY_POLL
|
|
db->flags |= DM9000_PLATF_SIMPLE_PHY;
|
|
#endif
|
|
|
|
dm9000_reset(db);
|
|
|
|
/* try multiple times, DM9000 sometimes gets the read wrong */
|
|
for (i = 0; i < 8; i++) {
|
|
id_val = ior(db, DM9000_VIDL);
|
|
id_val |= (u32)ior(db, DM9000_VIDH) << 8;
|
|
id_val |= (u32)ior(db, DM9000_PIDL) << 16;
|
|
id_val |= (u32)ior(db, DM9000_PIDH) << 24;
|
|
|
|
if (id_val == DM9000_ID)
|
|
break;
|
|
dev_err(db->dev, "read wrong id 0x%08x\n", id_val);
|
|
}
|
|
|
|
if (id_val != DM9000_ID) {
|
|
dev_err(db->dev, "wrong id: 0x%08x\n", id_val);
|
|
ret = -ENODEV;
|
|
goto out;
|
|
}
|
|
|
|
/* Identify what type of DM9000 we are working on */
|
|
|
|
id_val = ior(db, DM9000_CHIPR);
|
|
dev_dbg(db->dev, "dm9000 revision 0x%02x\n", id_val);
|
|
|
|
switch (id_val) {
|
|
case CHIPR_DM9000A:
|
|
db->type = TYPE_DM9000A;
|
|
break;
|
|
case CHIPR_DM9000B:
|
|
db->type = TYPE_DM9000B;
|
|
break;
|
|
default:
|
|
dev_dbg(db->dev, "ID %02x => defaulting to DM9000E\n", id_val);
|
|
db->type = TYPE_DM9000E;
|
|
}
|
|
|
|
/* dm9000a/b are capable of hardware checksum offload */
|
|
if (db->type == TYPE_DM9000A || db->type == TYPE_DM9000B) {
|
|
ndev->hw_features = NETIF_F_RXCSUM | NETIF_F_IP_CSUM;
|
|
ndev->features |= ndev->hw_features;
|
|
}
|
|
|
|
/* from this point we assume that we have found a DM9000 */
|
|
|
|
ndev->netdev_ops = &dm9000_netdev_ops;
|
|
ndev->watchdog_timeo = msecs_to_jiffies(watchdog);
|
|
ndev->ethtool_ops = &dm9000_ethtool_ops;
|
|
|
|
db->msg_enable = NETIF_MSG_LINK;
|
|
db->mii.phy_id_mask = 0x1f;
|
|
db->mii.reg_num_mask = 0x1f;
|
|
db->mii.force_media = 0;
|
|
db->mii.full_duplex = 0;
|
|
db->mii.dev = ndev;
|
|
db->mii.mdio_read = dm9000_phy_read;
|
|
db->mii.mdio_write = dm9000_phy_write;
|
|
|
|
mac_src = "eeprom";
|
|
|
|
/* try reading the node address from the attached EEPROM */
|
|
for (i = 0; i < 6; i += 2)
|
|
dm9000_read_eeprom(db, i / 2, addr + i);
|
|
eth_hw_addr_set(ndev, addr);
|
|
|
|
if (!is_valid_ether_addr(ndev->dev_addr) && pdata != NULL) {
|
|
mac_src = "platform data";
|
|
eth_hw_addr_set(ndev, pdata->dev_addr);
|
|
}
|
|
|
|
if (!is_valid_ether_addr(ndev->dev_addr)) {
|
|
/* try reading from mac */
|
|
|
|
mac_src = "chip";
|
|
for (i = 0; i < 6; i++)
|
|
addr[i] = ior(db, i + DM9000_PAR);
|
|
eth_hw_addr_set(ndev, pdata->dev_addr);
|
|
}
|
|
|
|
if (!is_valid_ether_addr(ndev->dev_addr)) {
|
|
inv_mac_addr = true;
|
|
eth_hw_addr_random(ndev);
|
|
mac_src = "random";
|
|
}
|
|
|
|
|
|
platform_set_drvdata(pdev, ndev);
|
|
ret = register_netdev(ndev);
|
|
|
|
if (ret == 0) {
|
|
if (inv_mac_addr)
|
|
dev_warn(db->dev, "%s: Invalid ethernet MAC address. Please set using ip\n",
|
|
ndev->name);
|
|
printk(KERN_INFO "%s: dm9000%c at %p,%p IRQ %d MAC: %pM (%s)\n",
|
|
ndev->name, dm9000_type_to_char(db->type),
|
|
db->io_addr, db->io_data, ndev->irq,
|
|
ndev->dev_addr, mac_src);
|
|
}
|
|
return 0;
|
|
|
|
out:
|
|
dev_err(db->dev, "not found (%d).\n", ret);
|
|
|
|
dm9000_release_board(pdev, db);
|
|
free_netdev(ndev);
|
|
|
|
out_regulator_disable:
|
|
if (!IS_ERR(power))
|
|
regulator_disable(power);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int
|
|
dm9000_drv_suspend(struct device *dev)
|
|
{
|
|
struct net_device *ndev = dev_get_drvdata(dev);
|
|
struct board_info *db;
|
|
|
|
if (ndev) {
|
|
db = netdev_priv(ndev);
|
|
db->in_suspend = 1;
|
|
|
|
if (!netif_running(ndev))
|
|
return 0;
|
|
|
|
netif_device_detach(ndev);
|
|
|
|
/* only shutdown if not using WoL */
|
|
if (!db->wake_state)
|
|
dm9000_shutdown(ndev);
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static int
|
|
dm9000_drv_resume(struct device *dev)
|
|
{
|
|
struct net_device *ndev = dev_get_drvdata(dev);
|
|
struct board_info *db = netdev_priv(ndev);
|
|
|
|
if (ndev) {
|
|
if (netif_running(ndev)) {
|
|
/* reset if we were not in wake mode to ensure if
|
|
* the device was powered off it is in a known state */
|
|
if (!db->wake_state) {
|
|
dm9000_init_dm9000(ndev);
|
|
dm9000_unmask_interrupts(db);
|
|
}
|
|
|
|
netif_device_attach(ndev);
|
|
}
|
|
|
|
db->in_suspend = 0;
|
|
}
|
|
return 0;
|
|
}
|
|
|
|
static const struct dev_pm_ops dm9000_drv_pm_ops = {
|
|
.suspend = dm9000_drv_suspend,
|
|
.resume = dm9000_drv_resume,
|
|
};
|
|
|
|
static int
|
|
dm9000_drv_remove(struct platform_device *pdev)
|
|
{
|
|
struct net_device *ndev = platform_get_drvdata(pdev);
|
|
struct board_info *dm = to_dm9000_board(ndev);
|
|
|
|
unregister_netdev(ndev);
|
|
dm9000_release_board(pdev, dm);
|
|
free_netdev(ndev); /* free device structure */
|
|
if (dm->power_supply)
|
|
regulator_disable(dm->power_supply);
|
|
|
|
dev_dbg(&pdev->dev, "released and freed device\n");
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_OF
|
|
static const struct of_device_id dm9000_of_matches[] = {
|
|
{ .compatible = "davicom,dm9000", },
|
|
{ /* sentinel */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, dm9000_of_matches);
|
|
#endif
|
|
|
|
static struct platform_driver dm9000_driver = {
|
|
.driver = {
|
|
.name = "dm9000",
|
|
.pm = &dm9000_drv_pm_ops,
|
|
.of_match_table = of_match_ptr(dm9000_of_matches),
|
|
},
|
|
.probe = dm9000_probe,
|
|
.remove = dm9000_drv_remove,
|
|
};
|
|
|
|
module_platform_driver(dm9000_driver);
|
|
|
|
MODULE_AUTHOR("Sascha Hauer, Ben Dooks");
|
|
MODULE_DESCRIPTION("Davicom DM9000 network driver");
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_ALIAS("platform:dm9000");
|