1496 lines
39 KiB
C
1496 lines
39 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/**
|
|
* SDHCI Controller driver for TI's OMAP SoCs
|
|
*
|
|
* Copyright (C) 2017 Texas Instruments
|
|
* Author: Kishon Vijay Abraham I <kishon@ti.com>
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/mmc/mmc.h>
|
|
#include <linux/mmc/slot-gpio.h>
|
|
#include <linux/module.h>
|
|
#include <linux/of.h>
|
|
#include <linux/of_device.h>
|
|
#include <linux/of_irq.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/pm_wakeirq.h>
|
|
#include <linux/regulator/consumer.h>
|
|
#include <linux/pinctrl/consumer.h>
|
|
#include <linux/sys_soc.h>
|
|
#include <linux/thermal.h>
|
|
|
|
#include "sdhci-pltfm.h"
|
|
|
|
/*
|
|
* Note that the register offsets used here are from omap_regs
|
|
* base which is 0x100 for omap4 and later, and 0 for omap3 and
|
|
* earlier.
|
|
*/
|
|
#define SDHCI_OMAP_SYSCONFIG 0x10
|
|
|
|
#define SDHCI_OMAP_CON 0x2c
|
|
#define CON_DW8 BIT(5)
|
|
#define CON_DMA_MASTER BIT(20)
|
|
#define CON_DDR BIT(19)
|
|
#define CON_CLKEXTFREE BIT(16)
|
|
#define CON_PADEN BIT(15)
|
|
#define CON_CTPL BIT(11)
|
|
#define CON_INIT BIT(1)
|
|
#define CON_OD BIT(0)
|
|
|
|
#define SDHCI_OMAP_DLL 0x34
|
|
#define DLL_SWT BIT(20)
|
|
#define DLL_FORCE_SR_C_SHIFT 13
|
|
#define DLL_FORCE_SR_C_MASK (0x7f << DLL_FORCE_SR_C_SHIFT)
|
|
#define DLL_FORCE_VALUE BIT(12)
|
|
#define DLL_CALIB BIT(1)
|
|
|
|
#define SDHCI_OMAP_CMD 0x10c
|
|
|
|
#define SDHCI_OMAP_PSTATE 0x124
|
|
#define PSTATE_DLEV_DAT0 BIT(20)
|
|
#define PSTATE_DATI BIT(1)
|
|
|
|
#define SDHCI_OMAP_HCTL 0x128
|
|
#define HCTL_SDBP BIT(8)
|
|
#define HCTL_SDVS_SHIFT 9
|
|
#define HCTL_SDVS_MASK (0x7 << HCTL_SDVS_SHIFT)
|
|
#define HCTL_SDVS_33 (0x7 << HCTL_SDVS_SHIFT)
|
|
#define HCTL_SDVS_30 (0x6 << HCTL_SDVS_SHIFT)
|
|
#define HCTL_SDVS_18 (0x5 << HCTL_SDVS_SHIFT)
|
|
|
|
#define SDHCI_OMAP_SYSCTL 0x12c
|
|
#define SYSCTL_CEN BIT(2)
|
|
#define SYSCTL_CLKD_SHIFT 6
|
|
#define SYSCTL_CLKD_MASK 0x3ff
|
|
|
|
#define SDHCI_OMAP_STAT 0x130
|
|
|
|
#define SDHCI_OMAP_IE 0x134
|
|
#define INT_CC_EN BIT(0)
|
|
|
|
#define SDHCI_OMAP_ISE 0x138
|
|
|
|
#define SDHCI_OMAP_AC12 0x13c
|
|
#define AC12_V1V8_SIGEN BIT(19)
|
|
#define AC12_SCLK_SEL BIT(23)
|
|
|
|
#define SDHCI_OMAP_CAPA 0x140
|
|
#define CAPA_VS33 BIT(24)
|
|
#define CAPA_VS30 BIT(25)
|
|
#define CAPA_VS18 BIT(26)
|
|
|
|
#define SDHCI_OMAP_CAPA2 0x144
|
|
#define CAPA2_TSDR50 BIT(13)
|
|
|
|
#define SDHCI_OMAP_TIMEOUT 1 /* 1 msec */
|
|
|
|
#define SYSCTL_CLKD_MAX 0x3FF
|
|
|
|
#define IOV_1V8 1800000 /* 180000 uV */
|
|
#define IOV_3V0 3000000 /* 300000 uV */
|
|
#define IOV_3V3 3300000 /* 330000 uV */
|
|
|
|
#define MAX_PHASE_DELAY 0x7C
|
|
|
|
/* sdhci-omap controller flags */
|
|
#define SDHCI_OMAP_REQUIRE_IODELAY BIT(0)
|
|
#define SDHCI_OMAP_SPECIAL_RESET BIT(1)
|
|
|
|
struct sdhci_omap_data {
|
|
int omap_offset; /* Offset for omap regs from base */
|
|
u32 offset; /* Offset for SDHCI regs from base */
|
|
u8 flags;
|
|
};
|
|
|
|
struct sdhci_omap_host {
|
|
char *version;
|
|
void __iomem *base;
|
|
struct device *dev;
|
|
struct regulator *pbias;
|
|
bool pbias_enabled;
|
|
struct sdhci_host *host;
|
|
u8 bus_mode;
|
|
u8 power_mode;
|
|
u8 timing;
|
|
u8 flags;
|
|
|
|
struct pinctrl *pinctrl;
|
|
struct pinctrl_state **pinctrl_state;
|
|
int wakeirq;
|
|
bool is_tuning;
|
|
|
|
/* Offset for omap specific registers from base */
|
|
int omap_offset;
|
|
|
|
/* Omap specific context save */
|
|
u32 con;
|
|
u32 hctl;
|
|
u32 sysctl;
|
|
u32 capa;
|
|
u32 ie;
|
|
u32 ise;
|
|
};
|
|
|
|
static void sdhci_omap_start_clock(struct sdhci_omap_host *omap_host);
|
|
static void sdhci_omap_stop_clock(struct sdhci_omap_host *omap_host);
|
|
|
|
static inline u32 sdhci_omap_readl(struct sdhci_omap_host *host,
|
|
unsigned int offset)
|
|
{
|
|
return readl(host->base + host->omap_offset + offset);
|
|
}
|
|
|
|
static inline void sdhci_omap_writel(struct sdhci_omap_host *host,
|
|
unsigned int offset, u32 data)
|
|
{
|
|
writel(data, host->base + host->omap_offset + offset);
|
|
}
|
|
|
|
static int sdhci_omap_set_pbias(struct sdhci_omap_host *omap_host,
|
|
bool power_on, unsigned int iov)
|
|
{
|
|
int ret;
|
|
struct device *dev = omap_host->dev;
|
|
|
|
if (IS_ERR(omap_host->pbias))
|
|
return 0;
|
|
|
|
if (power_on) {
|
|
ret = regulator_set_voltage(omap_host->pbias, iov, iov);
|
|
if (ret) {
|
|
dev_err(dev, "pbias set voltage failed\n");
|
|
return ret;
|
|
}
|
|
|
|
if (omap_host->pbias_enabled)
|
|
return 0;
|
|
|
|
ret = regulator_enable(omap_host->pbias);
|
|
if (ret) {
|
|
dev_err(dev, "pbias reg enable fail\n");
|
|
return ret;
|
|
}
|
|
|
|
omap_host->pbias_enabled = true;
|
|
} else {
|
|
if (!omap_host->pbias_enabled)
|
|
return 0;
|
|
|
|
ret = regulator_disable(omap_host->pbias);
|
|
if (ret) {
|
|
dev_err(dev, "pbias reg disable fail\n");
|
|
return ret;
|
|
}
|
|
omap_host->pbias_enabled = false;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int sdhci_omap_enable_iov(struct sdhci_omap_host *omap_host,
|
|
unsigned int iov_pbias)
|
|
{
|
|
int ret;
|
|
struct sdhci_host *host = omap_host->host;
|
|
struct mmc_host *mmc = host->mmc;
|
|
|
|
ret = sdhci_omap_set_pbias(omap_host, false, 0);
|
|
if (ret)
|
|
return ret;
|
|
|
|
if (!IS_ERR(mmc->supply.vqmmc)) {
|
|
/* Pick the right voltage to allow 3.0V for 3.3V nominal PBIAS */
|
|
ret = mmc_regulator_set_vqmmc(mmc, &mmc->ios);
|
|
if (ret < 0) {
|
|
dev_err(mmc_dev(mmc), "vqmmc set voltage failed\n");
|
|
return ret;
|
|
}
|
|
}
|
|
|
|
ret = sdhci_omap_set_pbias(omap_host, true, iov_pbias);
|
|
if (ret)
|
|
return ret;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void sdhci_omap_conf_bus_power(struct sdhci_omap_host *omap_host,
|
|
unsigned char signal_voltage)
|
|
{
|
|
u32 reg, capa;
|
|
ktime_t timeout;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_HCTL);
|
|
reg &= ~HCTL_SDVS_MASK;
|
|
|
|
switch (signal_voltage) {
|
|
case MMC_SIGNAL_VOLTAGE_330:
|
|
capa = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
|
|
if (capa & CAPA_VS33)
|
|
reg |= HCTL_SDVS_33;
|
|
else if (capa & CAPA_VS30)
|
|
reg |= HCTL_SDVS_30;
|
|
else
|
|
dev_warn(omap_host->dev, "misconfigured CAPA: %08x\n",
|
|
capa);
|
|
break;
|
|
case MMC_SIGNAL_VOLTAGE_180:
|
|
default:
|
|
reg |= HCTL_SDVS_18;
|
|
break;
|
|
}
|
|
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_HCTL, reg);
|
|
|
|
reg |= HCTL_SDBP;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_HCTL, reg);
|
|
|
|
/* wait 1ms */
|
|
timeout = ktime_add_ms(ktime_get(), SDHCI_OMAP_TIMEOUT);
|
|
while (1) {
|
|
bool timedout = ktime_after(ktime_get(), timeout);
|
|
|
|
if (sdhci_omap_readl(omap_host, SDHCI_OMAP_HCTL) & HCTL_SDBP)
|
|
break;
|
|
if (WARN_ON(timedout))
|
|
return;
|
|
usleep_range(5, 10);
|
|
}
|
|
}
|
|
|
|
static void sdhci_omap_enable_sdio_irq(struct mmc_host *mmc, int enable)
|
|
{
|
|
struct sdhci_host *host = mmc_priv(mmc);
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
u32 reg;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
if (enable)
|
|
reg |= (CON_CTPL | CON_CLKEXTFREE);
|
|
else
|
|
reg &= ~(CON_CTPL | CON_CLKEXTFREE);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
|
|
sdhci_enable_sdio_irq(mmc, enable);
|
|
}
|
|
|
|
static inline void sdhci_omap_set_dll(struct sdhci_omap_host *omap_host,
|
|
int count)
|
|
{
|
|
int i;
|
|
u32 reg;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_DLL);
|
|
reg |= DLL_FORCE_VALUE;
|
|
reg &= ~DLL_FORCE_SR_C_MASK;
|
|
reg |= (count << DLL_FORCE_SR_C_SHIFT);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_DLL, reg);
|
|
|
|
reg |= DLL_CALIB;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_DLL, reg);
|
|
for (i = 0; i < 1000; i++) {
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_DLL);
|
|
if (reg & DLL_CALIB)
|
|
break;
|
|
}
|
|
reg &= ~DLL_CALIB;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_DLL, reg);
|
|
}
|
|
|
|
static void sdhci_omap_disable_tuning(struct sdhci_omap_host *omap_host)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12);
|
|
reg &= ~AC12_SCLK_SEL;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_AC12, reg);
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_DLL);
|
|
reg &= ~(DLL_FORCE_VALUE | DLL_SWT);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_DLL, reg);
|
|
}
|
|
|
|
static int sdhci_omap_execute_tuning(struct mmc_host *mmc, u32 opcode)
|
|
{
|
|
struct sdhci_host *host = mmc_priv(mmc);
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
struct thermal_zone_device *thermal_dev;
|
|
struct device *dev = omap_host->dev;
|
|
struct mmc_ios *ios = &mmc->ios;
|
|
u32 start_window = 0, max_window = 0;
|
|
bool single_point_failure = false;
|
|
bool dcrc_was_enabled = false;
|
|
u8 cur_match, prev_match = 0;
|
|
u32 length = 0, max_len = 0;
|
|
u32 phase_delay = 0;
|
|
int temperature;
|
|
int ret = 0;
|
|
u32 reg;
|
|
int i;
|
|
|
|
/* clock tuning is not needed for upto 52MHz */
|
|
if (ios->clock <= 52000000)
|
|
return 0;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA2);
|
|
if (ios->timing == MMC_TIMING_UHS_SDR50 && !(reg & CAPA2_TSDR50))
|
|
return 0;
|
|
|
|
thermal_dev = thermal_zone_get_zone_by_name("cpu_thermal");
|
|
if (IS_ERR(thermal_dev)) {
|
|
dev_err(dev, "Unable to get thermal zone for tuning\n");
|
|
return PTR_ERR(thermal_dev);
|
|
}
|
|
|
|
ret = thermal_zone_get_temp(thermal_dev, &temperature);
|
|
if (ret)
|
|
return ret;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_DLL);
|
|
reg |= DLL_SWT;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_DLL, reg);
|
|
|
|
/*
|
|
* OMAP5/DRA74X/DRA72x Errata i802:
|
|
* DCRC error interrupts (MMCHS_STAT[21] DCRC=0x1) can occur
|
|
* during the tuning procedure. So disable it during the
|
|
* tuning procedure.
|
|
*/
|
|
if (host->ier & SDHCI_INT_DATA_CRC) {
|
|
host->ier &= ~SDHCI_INT_DATA_CRC;
|
|
dcrc_was_enabled = true;
|
|
}
|
|
|
|
omap_host->is_tuning = true;
|
|
|
|
/*
|
|
* Stage 1: Search for a maximum pass window ignoring any
|
|
* any single point failures. If the tuning value ends up
|
|
* near it, move away from it in stage 2 below
|
|
*/
|
|
while (phase_delay <= MAX_PHASE_DELAY) {
|
|
sdhci_omap_set_dll(omap_host, phase_delay);
|
|
|
|
cur_match = !mmc_send_tuning(mmc, opcode, NULL);
|
|
if (cur_match) {
|
|
if (prev_match) {
|
|
length++;
|
|
} else if (single_point_failure) {
|
|
/* ignore single point failure */
|
|
length++;
|
|
} else {
|
|
start_window = phase_delay;
|
|
length = 1;
|
|
}
|
|
} else {
|
|
single_point_failure = prev_match;
|
|
}
|
|
|
|
if (length > max_len) {
|
|
max_window = start_window;
|
|
max_len = length;
|
|
}
|
|
|
|
prev_match = cur_match;
|
|
phase_delay += 4;
|
|
}
|
|
|
|
if (!max_len) {
|
|
dev_err(dev, "Unable to find match\n");
|
|
ret = -EIO;
|
|
goto tuning_error;
|
|
}
|
|
|
|
/*
|
|
* Assign tuning value as a ratio of maximum pass window based
|
|
* on temperature
|
|
*/
|
|
if (temperature < -20000)
|
|
phase_delay = min(max_window + 4 * (max_len - 1) - 24,
|
|
max_window +
|
|
DIV_ROUND_UP(13 * max_len, 16) * 4);
|
|
else if (temperature < 20000)
|
|
phase_delay = max_window + DIV_ROUND_UP(9 * max_len, 16) * 4;
|
|
else if (temperature < 40000)
|
|
phase_delay = max_window + DIV_ROUND_UP(8 * max_len, 16) * 4;
|
|
else if (temperature < 70000)
|
|
phase_delay = max_window + DIV_ROUND_UP(7 * max_len, 16) * 4;
|
|
else if (temperature < 90000)
|
|
phase_delay = max_window + DIV_ROUND_UP(5 * max_len, 16) * 4;
|
|
else if (temperature < 120000)
|
|
phase_delay = max_window + DIV_ROUND_UP(4 * max_len, 16) * 4;
|
|
else
|
|
phase_delay = max_window + DIV_ROUND_UP(3 * max_len, 16) * 4;
|
|
|
|
/*
|
|
* Stage 2: Search for a single point failure near the chosen tuning
|
|
* value in two steps. First in the +3 to +10 range and then in the
|
|
* +2 to -10 range. If found, move away from it in the appropriate
|
|
* direction by the appropriate amount depending on the temperature.
|
|
*/
|
|
for (i = 3; i <= 10; i++) {
|
|
sdhci_omap_set_dll(omap_host, phase_delay + i);
|
|
|
|
if (mmc_send_tuning(mmc, opcode, NULL)) {
|
|
if (temperature < 10000)
|
|
phase_delay += i + 6;
|
|
else if (temperature < 20000)
|
|
phase_delay += i - 12;
|
|
else if (temperature < 70000)
|
|
phase_delay += i - 8;
|
|
else
|
|
phase_delay += i - 6;
|
|
|
|
goto single_failure_found;
|
|
}
|
|
}
|
|
|
|
for (i = 2; i >= -10; i--) {
|
|
sdhci_omap_set_dll(omap_host, phase_delay + i);
|
|
|
|
if (mmc_send_tuning(mmc, opcode, NULL)) {
|
|
if (temperature < 10000)
|
|
phase_delay += i + 12;
|
|
else if (temperature < 20000)
|
|
phase_delay += i + 8;
|
|
else if (temperature < 70000)
|
|
phase_delay += i + 8;
|
|
else if (temperature < 90000)
|
|
phase_delay += i + 10;
|
|
else
|
|
phase_delay += i + 12;
|
|
|
|
goto single_failure_found;
|
|
}
|
|
}
|
|
|
|
single_failure_found:
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12);
|
|
if (!(reg & AC12_SCLK_SEL)) {
|
|
ret = -EIO;
|
|
goto tuning_error;
|
|
}
|
|
|
|
sdhci_omap_set_dll(omap_host, phase_delay);
|
|
|
|
omap_host->is_tuning = false;
|
|
|
|
goto ret;
|
|
|
|
tuning_error:
|
|
omap_host->is_tuning = false;
|
|
dev_err(dev, "Tuning failed\n");
|
|
sdhci_omap_disable_tuning(omap_host);
|
|
|
|
ret:
|
|
sdhci_reset(host, SDHCI_RESET_CMD | SDHCI_RESET_DATA);
|
|
/* Reenable forbidden interrupt */
|
|
if (dcrc_was_enabled)
|
|
host->ier |= SDHCI_INT_DATA_CRC;
|
|
sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
|
|
sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
|
|
return ret;
|
|
}
|
|
|
|
static int sdhci_omap_card_busy(struct mmc_host *mmc)
|
|
{
|
|
u32 reg, ac12;
|
|
int ret = false;
|
|
struct sdhci_host *host = mmc_priv(mmc);
|
|
struct sdhci_pltfm_host *pltfm_host;
|
|
struct sdhci_omap_host *omap_host;
|
|
u32 ier = host->ier;
|
|
|
|
pltfm_host = sdhci_priv(host);
|
|
omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
ac12 = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12);
|
|
reg &= ~CON_CLKEXTFREE;
|
|
if (ac12 & AC12_V1V8_SIGEN)
|
|
reg |= CON_CLKEXTFREE;
|
|
reg |= CON_PADEN;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
|
|
disable_irq(host->irq);
|
|
ier |= SDHCI_INT_CARD_INT;
|
|
sdhci_writel(host, ier, SDHCI_INT_ENABLE);
|
|
sdhci_writel(host, ier, SDHCI_SIGNAL_ENABLE);
|
|
|
|
/*
|
|
* Delay is required for PSTATE to correctly reflect
|
|
* DLEV/CLEV values after PADEN is set.
|
|
*/
|
|
usleep_range(50, 100);
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_PSTATE);
|
|
if ((reg & PSTATE_DATI) || !(reg & PSTATE_DLEV_DAT0))
|
|
ret = true;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
reg &= ~(CON_CLKEXTFREE | CON_PADEN);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
|
|
sdhci_writel(host, host->ier, SDHCI_INT_ENABLE);
|
|
sdhci_writel(host, host->ier, SDHCI_SIGNAL_ENABLE);
|
|
enable_irq(host->irq);
|
|
|
|
return ret;
|
|
}
|
|
|
|
static int sdhci_omap_start_signal_voltage_switch(struct mmc_host *mmc,
|
|
struct mmc_ios *ios)
|
|
{
|
|
u32 reg;
|
|
int ret;
|
|
unsigned int iov;
|
|
struct sdhci_host *host = mmc_priv(mmc);
|
|
struct sdhci_pltfm_host *pltfm_host;
|
|
struct sdhci_omap_host *omap_host;
|
|
struct device *dev;
|
|
|
|
pltfm_host = sdhci_priv(host);
|
|
omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
dev = omap_host->dev;
|
|
|
|
if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
|
|
if (!(reg & (CAPA_VS30 | CAPA_VS33)))
|
|
return -EOPNOTSUPP;
|
|
|
|
if (reg & CAPA_VS30)
|
|
iov = IOV_3V0;
|
|
else
|
|
iov = IOV_3V3;
|
|
|
|
sdhci_omap_conf_bus_power(omap_host, ios->signal_voltage);
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12);
|
|
reg &= ~AC12_V1V8_SIGEN;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_AC12, reg);
|
|
|
|
} else if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180) {
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
|
|
if (!(reg & CAPA_VS18))
|
|
return -EOPNOTSUPP;
|
|
|
|
iov = IOV_1V8;
|
|
|
|
sdhci_omap_conf_bus_power(omap_host, ios->signal_voltage);
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12);
|
|
reg |= AC12_V1V8_SIGEN;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_AC12, reg);
|
|
} else {
|
|
return -EOPNOTSUPP;
|
|
}
|
|
|
|
ret = sdhci_omap_enable_iov(omap_host, iov);
|
|
if (ret) {
|
|
dev_err(dev, "failed to switch IO voltage to %dmV\n", iov);
|
|
return ret;
|
|
}
|
|
|
|
dev_dbg(dev, "IO voltage switched to %dmV\n", iov);
|
|
return 0;
|
|
}
|
|
|
|
static void sdhci_omap_set_timing(struct sdhci_omap_host *omap_host, u8 timing)
|
|
{
|
|
int ret;
|
|
struct pinctrl_state *pinctrl_state;
|
|
struct device *dev = omap_host->dev;
|
|
|
|
if (!(omap_host->flags & SDHCI_OMAP_REQUIRE_IODELAY))
|
|
return;
|
|
|
|
if (omap_host->timing == timing)
|
|
return;
|
|
|
|
sdhci_omap_stop_clock(omap_host);
|
|
|
|
pinctrl_state = omap_host->pinctrl_state[timing];
|
|
ret = pinctrl_select_state(omap_host->pinctrl, pinctrl_state);
|
|
if (ret) {
|
|
dev_err(dev, "failed to select pinctrl state\n");
|
|
return;
|
|
}
|
|
|
|
sdhci_omap_start_clock(omap_host);
|
|
omap_host->timing = timing;
|
|
}
|
|
|
|
static void sdhci_omap_set_power_mode(struct sdhci_omap_host *omap_host,
|
|
u8 power_mode)
|
|
{
|
|
if (omap_host->bus_mode == MMC_POWER_OFF)
|
|
sdhci_omap_disable_tuning(omap_host);
|
|
omap_host->power_mode = power_mode;
|
|
}
|
|
|
|
static void sdhci_omap_set_bus_mode(struct sdhci_omap_host *omap_host,
|
|
unsigned int mode)
|
|
{
|
|
u32 reg;
|
|
|
|
if (omap_host->bus_mode == mode)
|
|
return;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
if (mode == MMC_BUSMODE_OPENDRAIN)
|
|
reg |= CON_OD;
|
|
else
|
|
reg &= ~CON_OD;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
|
|
omap_host->bus_mode = mode;
|
|
}
|
|
|
|
static void sdhci_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
|
|
{
|
|
struct sdhci_host *host = mmc_priv(mmc);
|
|
struct sdhci_pltfm_host *pltfm_host;
|
|
struct sdhci_omap_host *omap_host;
|
|
|
|
pltfm_host = sdhci_priv(host);
|
|
omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
sdhci_omap_set_bus_mode(omap_host, ios->bus_mode);
|
|
sdhci_omap_set_timing(omap_host, ios->timing);
|
|
sdhci_set_ios(mmc, ios);
|
|
sdhci_omap_set_power_mode(omap_host, ios->power_mode);
|
|
}
|
|
|
|
static u16 sdhci_omap_calc_divisor(struct sdhci_pltfm_host *host,
|
|
unsigned int clock)
|
|
{
|
|
u16 dsor;
|
|
|
|
dsor = DIV_ROUND_UP(clk_get_rate(host->clk), clock);
|
|
if (dsor > SYSCTL_CLKD_MAX)
|
|
dsor = SYSCTL_CLKD_MAX;
|
|
|
|
return dsor;
|
|
}
|
|
|
|
static void sdhci_omap_start_clock(struct sdhci_omap_host *omap_host)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_SYSCTL);
|
|
reg |= SYSCTL_CEN;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_SYSCTL, reg);
|
|
}
|
|
|
|
static void sdhci_omap_stop_clock(struct sdhci_omap_host *omap_host)
|
|
{
|
|
u32 reg;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_SYSCTL);
|
|
reg &= ~SYSCTL_CEN;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_SYSCTL, reg);
|
|
}
|
|
|
|
static void sdhci_omap_set_clock(struct sdhci_host *host, unsigned int clock)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
unsigned long clkdiv;
|
|
|
|
sdhci_omap_stop_clock(omap_host);
|
|
|
|
if (!clock)
|
|
return;
|
|
|
|
clkdiv = sdhci_omap_calc_divisor(pltfm_host, clock);
|
|
clkdiv = (clkdiv & SYSCTL_CLKD_MASK) << SYSCTL_CLKD_SHIFT;
|
|
sdhci_enable_clk(host, clkdiv);
|
|
|
|
sdhci_omap_start_clock(omap_host);
|
|
}
|
|
|
|
static void sdhci_omap_set_power(struct sdhci_host *host, unsigned char mode,
|
|
unsigned short vdd)
|
|
{
|
|
struct mmc_host *mmc = host->mmc;
|
|
|
|
if (!IS_ERR(mmc->supply.vmmc))
|
|
mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
|
|
}
|
|
|
|
/*
|
|
* MMCHS_HL_HWINFO has the MADMA_EN bit set if the controller instance
|
|
* is connected to L3 interconnect and is bus master capable. Note that
|
|
* the MMCHS_HL_HWINFO register is in the module registers before the
|
|
* omap registers and sdhci registers. The offset can vary for omap
|
|
* registers depending on the SoC. Do not use sdhci_omap_readl() here.
|
|
*/
|
|
static bool sdhci_omap_has_adma(struct sdhci_omap_host *omap_host, int offset)
|
|
{
|
|
/* MMCHS_HL_HWINFO register is only available on omap4 and later */
|
|
if (offset < 0x200)
|
|
return false;
|
|
|
|
return readl(omap_host->base + 4) & 1;
|
|
}
|
|
|
|
static int sdhci_omap_enable_dma(struct sdhci_host *host)
|
|
{
|
|
u32 reg;
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
reg &= ~CON_DMA_MASTER;
|
|
/* Switch to DMA slave mode when using external DMA */
|
|
if (!host->use_external_dma)
|
|
reg |= CON_DMA_MASTER;
|
|
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static unsigned int sdhci_omap_get_min_clock(struct sdhci_host *host)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
|
|
return clk_get_rate(pltfm_host->clk) / SYSCTL_CLKD_MAX;
|
|
}
|
|
|
|
static void sdhci_omap_set_bus_width(struct sdhci_host *host, int width)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
u32 reg;
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
if (width == MMC_BUS_WIDTH_8)
|
|
reg |= CON_DW8;
|
|
else
|
|
reg &= ~CON_DW8;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
|
|
sdhci_set_bus_width(host, width);
|
|
}
|
|
|
|
static void sdhci_omap_init_74_clocks(struct sdhci_host *host, u8 power_mode)
|
|
{
|
|
u32 reg;
|
|
ktime_t timeout;
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
if (omap_host->power_mode == power_mode)
|
|
return;
|
|
|
|
if (power_mode != MMC_POWER_ON)
|
|
return;
|
|
|
|
disable_irq(host->irq);
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
reg |= CON_INIT;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CMD, 0x0);
|
|
|
|
/* wait 1ms */
|
|
timeout = ktime_add_ms(ktime_get(), SDHCI_OMAP_TIMEOUT);
|
|
while (1) {
|
|
bool timedout = ktime_after(ktime_get(), timeout);
|
|
|
|
if (sdhci_omap_readl(omap_host, SDHCI_OMAP_STAT) & INT_CC_EN)
|
|
break;
|
|
if (WARN_ON(timedout))
|
|
return;
|
|
usleep_range(5, 10);
|
|
}
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
reg &= ~CON_INIT;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_STAT, INT_CC_EN);
|
|
|
|
enable_irq(host->irq);
|
|
}
|
|
|
|
static void sdhci_omap_set_uhs_signaling(struct sdhci_host *host,
|
|
unsigned int timing)
|
|
{
|
|
u32 reg;
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
sdhci_omap_stop_clock(omap_host);
|
|
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
if (timing == MMC_TIMING_UHS_DDR50 || timing == MMC_TIMING_MMC_DDR52)
|
|
reg |= CON_DDR;
|
|
else
|
|
reg &= ~CON_DDR;
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
|
|
|
|
sdhci_set_uhs_signaling(host, timing);
|
|
sdhci_omap_start_clock(omap_host);
|
|
}
|
|
|
|
#define MMC_TIMEOUT_US 20000 /* 20000 micro Sec */
|
|
static void sdhci_omap_reset(struct sdhci_host *host, u8 mask)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
unsigned long limit = MMC_TIMEOUT_US;
|
|
unsigned long i = 0;
|
|
u32 sysc;
|
|
|
|
/* Save target module sysconfig configured by SoC PM layer */
|
|
if (mask & SDHCI_RESET_ALL)
|
|
sysc = sdhci_omap_readl(omap_host, SDHCI_OMAP_SYSCONFIG);
|
|
|
|
/* Don't reset data lines during tuning operation */
|
|
if (omap_host->is_tuning)
|
|
mask &= ~SDHCI_RESET_DATA;
|
|
|
|
if (omap_host->flags & SDHCI_OMAP_SPECIAL_RESET) {
|
|
sdhci_writeb(host, mask, SDHCI_SOFTWARE_RESET);
|
|
while ((!(sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask)) &&
|
|
(i++ < limit))
|
|
udelay(1);
|
|
i = 0;
|
|
while ((sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask) &&
|
|
(i++ < limit))
|
|
udelay(1);
|
|
|
|
if (sdhci_readb(host, SDHCI_SOFTWARE_RESET) & mask)
|
|
dev_err(mmc_dev(host->mmc),
|
|
"Timeout waiting on controller reset in %s\n",
|
|
__func__);
|
|
|
|
goto restore_sysc;
|
|
}
|
|
|
|
sdhci_reset(host, mask);
|
|
|
|
restore_sysc:
|
|
if (mask & SDHCI_RESET_ALL)
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_SYSCONFIG, sysc);
|
|
}
|
|
|
|
#define CMD_ERR_MASK (SDHCI_INT_CRC | SDHCI_INT_END_BIT | SDHCI_INT_INDEX |\
|
|
SDHCI_INT_TIMEOUT)
|
|
#define CMD_MASK (CMD_ERR_MASK | SDHCI_INT_RESPONSE)
|
|
|
|
static u32 sdhci_omap_irq(struct sdhci_host *host, u32 intmask)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
if (omap_host->is_tuning && host->cmd && !host->data_early &&
|
|
(intmask & CMD_ERR_MASK)) {
|
|
|
|
/*
|
|
* Since we are not resetting data lines during tuning
|
|
* operation, data error or data complete interrupts
|
|
* might still arrive. Mark this request as a failure
|
|
* but still wait for the data interrupt
|
|
*/
|
|
if (intmask & SDHCI_INT_TIMEOUT)
|
|
host->cmd->error = -ETIMEDOUT;
|
|
else
|
|
host->cmd->error = -EILSEQ;
|
|
|
|
host->cmd = NULL;
|
|
|
|
/*
|
|
* Sometimes command error interrupts and command complete
|
|
* interrupt will arrive together. Clear all command related
|
|
* interrupts here.
|
|
*/
|
|
sdhci_writel(host, intmask & CMD_MASK, SDHCI_INT_STATUS);
|
|
intmask &= ~CMD_MASK;
|
|
}
|
|
|
|
return intmask;
|
|
}
|
|
|
|
static void sdhci_omap_set_timeout(struct sdhci_host *host,
|
|
struct mmc_command *cmd)
|
|
{
|
|
if (cmd->opcode == MMC_ERASE)
|
|
sdhci_set_data_timeout_irq(host, false);
|
|
|
|
__sdhci_set_timeout(host, cmd);
|
|
}
|
|
|
|
static struct sdhci_ops sdhci_omap_ops = {
|
|
.set_clock = sdhci_omap_set_clock,
|
|
.set_power = sdhci_omap_set_power,
|
|
.enable_dma = sdhci_omap_enable_dma,
|
|
.get_max_clock = sdhci_pltfm_clk_get_max_clock,
|
|
.get_min_clock = sdhci_omap_get_min_clock,
|
|
.set_bus_width = sdhci_omap_set_bus_width,
|
|
.platform_send_init_74_clocks = sdhci_omap_init_74_clocks,
|
|
.reset = sdhci_omap_reset,
|
|
.set_uhs_signaling = sdhci_omap_set_uhs_signaling,
|
|
.irq = sdhci_omap_irq,
|
|
.set_timeout = sdhci_omap_set_timeout,
|
|
};
|
|
|
|
static unsigned int sdhci_omap_regulator_get_caps(struct device *dev,
|
|
const char *name)
|
|
{
|
|
struct regulator *reg;
|
|
unsigned int caps = 0;
|
|
|
|
reg = regulator_get(dev, name);
|
|
if (IS_ERR(reg))
|
|
return ~0U;
|
|
|
|
if (regulator_is_supported_voltage(reg, 1700000, 1950000))
|
|
caps |= SDHCI_CAN_VDD_180;
|
|
if (regulator_is_supported_voltage(reg, 2700000, 3150000))
|
|
caps |= SDHCI_CAN_VDD_300;
|
|
if (regulator_is_supported_voltage(reg, 3150000, 3600000))
|
|
caps |= SDHCI_CAN_VDD_330;
|
|
|
|
regulator_put(reg);
|
|
|
|
return caps;
|
|
}
|
|
|
|
static int sdhci_omap_set_capabilities(struct sdhci_host *host)
|
|
{
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
struct device *dev = omap_host->dev;
|
|
const u32 mask = SDHCI_CAN_VDD_180 | SDHCI_CAN_VDD_300 | SDHCI_CAN_VDD_330;
|
|
unsigned int pbias, vqmmc, caps = 0;
|
|
u32 reg;
|
|
|
|
pbias = sdhci_omap_regulator_get_caps(dev, "pbias");
|
|
vqmmc = sdhci_omap_regulator_get_caps(dev, "vqmmc");
|
|
caps = pbias & vqmmc;
|
|
|
|
if (pbias != ~0U && vqmmc == ~0U)
|
|
dev_warn(dev, "vqmmc regulator missing for pbias\n");
|
|
else if (caps == ~0U)
|
|
return 0;
|
|
|
|
/*
|
|
* Quirk handling to allow 3.0V vqmmc with a valid 3.3V PBIAS. This is
|
|
* needed for 3.0V ldo9_reg on omap5 at least.
|
|
*/
|
|
if (pbias != ~0U && (pbias & SDHCI_CAN_VDD_330) &&
|
|
(vqmmc & SDHCI_CAN_VDD_300))
|
|
caps |= SDHCI_CAN_VDD_330;
|
|
|
|
/* voltage capabilities might be set by boot loader, clear it */
|
|
reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
|
|
reg &= ~(CAPA_VS18 | CAPA_VS30 | CAPA_VS33);
|
|
|
|
if (caps & SDHCI_CAN_VDD_180)
|
|
reg |= CAPA_VS18;
|
|
|
|
if (caps & SDHCI_CAN_VDD_300)
|
|
reg |= CAPA_VS30;
|
|
|
|
if (caps & SDHCI_CAN_VDD_330)
|
|
reg |= CAPA_VS33;
|
|
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CAPA, reg);
|
|
|
|
host->caps &= ~mask;
|
|
host->caps |= caps;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct sdhci_pltfm_data sdhci_omap_pdata = {
|
|
.quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
|
|
SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
|
|
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
|
|
SDHCI_QUIRK_NO_HISPD_BIT |
|
|
SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC,
|
|
.quirks2 = SDHCI_QUIRK2_ACMD23_BROKEN |
|
|
SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
|
|
SDHCI_QUIRK2_RSP_136_HAS_CRC |
|
|
SDHCI_QUIRK2_DISABLE_HW_TIMEOUT,
|
|
.ops = &sdhci_omap_ops,
|
|
};
|
|
|
|
static const struct sdhci_omap_data omap2430_data = {
|
|
.omap_offset = 0,
|
|
.offset = 0x100,
|
|
};
|
|
|
|
static const struct sdhci_omap_data omap3_data = {
|
|
.omap_offset = 0,
|
|
.offset = 0x100,
|
|
};
|
|
|
|
static const struct sdhci_omap_data omap4_data = {
|
|
.omap_offset = 0x100,
|
|
.offset = 0x200,
|
|
.flags = SDHCI_OMAP_SPECIAL_RESET,
|
|
};
|
|
|
|
static const struct sdhci_omap_data omap5_data = {
|
|
.omap_offset = 0x100,
|
|
.offset = 0x200,
|
|
.flags = SDHCI_OMAP_SPECIAL_RESET,
|
|
};
|
|
|
|
static const struct sdhci_omap_data k2g_data = {
|
|
.omap_offset = 0x100,
|
|
.offset = 0x200,
|
|
};
|
|
|
|
static const struct sdhci_omap_data am335_data = {
|
|
.omap_offset = 0x100,
|
|
.offset = 0x200,
|
|
.flags = SDHCI_OMAP_SPECIAL_RESET,
|
|
};
|
|
|
|
static const struct sdhci_omap_data am437_data = {
|
|
.omap_offset = 0x100,
|
|
.offset = 0x200,
|
|
.flags = SDHCI_OMAP_SPECIAL_RESET,
|
|
};
|
|
|
|
static const struct sdhci_omap_data dra7_data = {
|
|
.omap_offset = 0x100,
|
|
.offset = 0x200,
|
|
.flags = SDHCI_OMAP_REQUIRE_IODELAY,
|
|
};
|
|
|
|
static const struct of_device_id omap_sdhci_match[] = {
|
|
{ .compatible = "ti,omap2430-sdhci", .data = &omap2430_data },
|
|
{ .compatible = "ti,omap3-sdhci", .data = &omap3_data },
|
|
{ .compatible = "ti,omap4-sdhci", .data = &omap4_data },
|
|
{ .compatible = "ti,omap5-sdhci", .data = &omap5_data },
|
|
{ .compatible = "ti,dra7-sdhci", .data = &dra7_data },
|
|
{ .compatible = "ti,k2g-sdhci", .data = &k2g_data },
|
|
{ .compatible = "ti,am335-sdhci", .data = &am335_data },
|
|
{ .compatible = "ti,am437-sdhci", .data = &am437_data },
|
|
{},
|
|
};
|
|
MODULE_DEVICE_TABLE(of, omap_sdhci_match);
|
|
|
|
static struct pinctrl_state
|
|
*sdhci_omap_iodelay_pinctrl_state(struct sdhci_omap_host *omap_host, char *mode,
|
|
u32 *caps, u32 capmask)
|
|
{
|
|
struct device *dev = omap_host->dev;
|
|
char *version = omap_host->version;
|
|
struct pinctrl_state *pinctrl_state = ERR_PTR(-ENODEV);
|
|
char str[20];
|
|
|
|
if (!(*caps & capmask))
|
|
goto ret;
|
|
|
|
if (version) {
|
|
snprintf(str, 20, "%s-%s", mode, version);
|
|
pinctrl_state = pinctrl_lookup_state(omap_host->pinctrl, str);
|
|
}
|
|
|
|
if (IS_ERR(pinctrl_state))
|
|
pinctrl_state = pinctrl_lookup_state(omap_host->pinctrl, mode);
|
|
|
|
if (IS_ERR(pinctrl_state)) {
|
|
dev_err(dev, "no pinctrl state for %s mode", mode);
|
|
*caps &= ~capmask;
|
|
}
|
|
|
|
ret:
|
|
return pinctrl_state;
|
|
}
|
|
|
|
static int sdhci_omap_config_iodelay_pinctrl_state(struct sdhci_omap_host
|
|
*omap_host)
|
|
{
|
|
struct device *dev = omap_host->dev;
|
|
struct sdhci_host *host = omap_host->host;
|
|
struct mmc_host *mmc = host->mmc;
|
|
u32 *caps = &mmc->caps;
|
|
u32 *caps2 = &mmc->caps2;
|
|
struct pinctrl_state *state;
|
|
struct pinctrl_state **pinctrl_state;
|
|
|
|
if (!(omap_host->flags & SDHCI_OMAP_REQUIRE_IODELAY))
|
|
return 0;
|
|
|
|
pinctrl_state = devm_kcalloc(dev,
|
|
MMC_TIMING_MMC_HS200 + 1,
|
|
sizeof(*pinctrl_state),
|
|
GFP_KERNEL);
|
|
if (!pinctrl_state)
|
|
return -ENOMEM;
|
|
|
|
omap_host->pinctrl = devm_pinctrl_get(omap_host->dev);
|
|
if (IS_ERR(omap_host->pinctrl)) {
|
|
dev_err(dev, "Cannot get pinctrl\n");
|
|
return PTR_ERR(omap_host->pinctrl);
|
|
}
|
|
|
|
state = pinctrl_lookup_state(omap_host->pinctrl, "default");
|
|
if (IS_ERR(state)) {
|
|
dev_err(dev, "no pinctrl state for default mode\n");
|
|
return PTR_ERR(state);
|
|
}
|
|
pinctrl_state[MMC_TIMING_LEGACY] = state;
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "sdr104", caps,
|
|
MMC_CAP_UHS_SDR104);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_UHS_SDR104] = state;
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr50", caps,
|
|
MMC_CAP_UHS_DDR50);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_UHS_DDR50] = state;
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "sdr50", caps,
|
|
MMC_CAP_UHS_SDR50);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_UHS_SDR50] = state;
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "sdr25", caps,
|
|
MMC_CAP_UHS_SDR25);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_UHS_SDR25] = state;
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "sdr12", caps,
|
|
MMC_CAP_UHS_SDR12);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_UHS_SDR12] = state;
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_1_8v", caps,
|
|
MMC_CAP_1_8V_DDR);
|
|
if (!IS_ERR(state)) {
|
|
pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
|
|
} else {
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "ddr_3_3v",
|
|
caps,
|
|
MMC_CAP_3_3V_DDR);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_MMC_DDR52] = state;
|
|
}
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "hs", caps,
|
|
MMC_CAP_SD_HIGHSPEED);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_SD_HS] = state;
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "hs", caps,
|
|
MMC_CAP_MMC_HIGHSPEED);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_MMC_HS] = state;
|
|
|
|
state = sdhci_omap_iodelay_pinctrl_state(omap_host, "hs200_1_8v", caps2,
|
|
MMC_CAP2_HS200_1_8V_SDR);
|
|
if (!IS_ERR(state))
|
|
pinctrl_state[MMC_TIMING_MMC_HS200] = state;
|
|
|
|
omap_host->pinctrl_state = pinctrl_state;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct soc_device_attribute sdhci_omap_soc_devices[] = {
|
|
{
|
|
.machine = "DRA7[45]*",
|
|
.revision = "ES1.[01]",
|
|
},
|
|
{
|
|
/* sentinel */
|
|
}
|
|
};
|
|
|
|
static int sdhci_omap_probe(struct platform_device *pdev)
|
|
{
|
|
int ret;
|
|
u32 offset;
|
|
struct device *dev = &pdev->dev;
|
|
struct sdhci_host *host;
|
|
struct sdhci_pltfm_host *pltfm_host;
|
|
struct sdhci_omap_host *omap_host;
|
|
struct mmc_host *mmc;
|
|
const struct sdhci_omap_data *data;
|
|
const struct soc_device_attribute *soc;
|
|
struct resource *regs;
|
|
|
|
data = of_device_get_match_data(&pdev->dev);
|
|
if (!data) {
|
|
dev_err(dev, "no sdhci omap data\n");
|
|
return -EINVAL;
|
|
}
|
|
offset = data->offset;
|
|
|
|
regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
|
|
if (!regs)
|
|
return -ENXIO;
|
|
|
|
host = sdhci_pltfm_init(pdev, &sdhci_omap_pdata,
|
|
sizeof(*omap_host));
|
|
if (IS_ERR(host)) {
|
|
dev_err(dev, "Failed sdhci_pltfm_init\n");
|
|
return PTR_ERR(host);
|
|
}
|
|
|
|
pltfm_host = sdhci_priv(host);
|
|
omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
omap_host->host = host;
|
|
omap_host->base = host->ioaddr;
|
|
omap_host->dev = dev;
|
|
omap_host->power_mode = MMC_POWER_UNDEFINED;
|
|
omap_host->timing = MMC_TIMING_LEGACY;
|
|
omap_host->flags = data->flags;
|
|
omap_host->omap_offset = data->omap_offset;
|
|
omap_host->con = -EINVAL; /* Prevent invalid restore on first resume */
|
|
host->ioaddr += offset;
|
|
host->mapbase = regs->start + offset;
|
|
|
|
mmc = host->mmc;
|
|
sdhci_get_of_property(pdev);
|
|
ret = mmc_of_parse(mmc);
|
|
if (ret)
|
|
goto err_pltfm_free;
|
|
|
|
soc = soc_device_match(sdhci_omap_soc_devices);
|
|
if (soc) {
|
|
omap_host->version = "rev11";
|
|
if (!strcmp(dev_name(dev), "4809c000.mmc"))
|
|
mmc->f_max = 96000000;
|
|
if (!strcmp(dev_name(dev), "480b4000.mmc"))
|
|
mmc->f_max = 48000000;
|
|
if (!strcmp(dev_name(dev), "480ad000.mmc"))
|
|
mmc->f_max = 48000000;
|
|
}
|
|
|
|
if (!mmc_can_gpio_ro(mmc))
|
|
mmc->caps2 |= MMC_CAP2_NO_WRITE_PROTECT;
|
|
|
|
pltfm_host->clk = devm_clk_get(dev, "fck");
|
|
if (IS_ERR(pltfm_host->clk)) {
|
|
ret = PTR_ERR(pltfm_host->clk);
|
|
goto err_pltfm_free;
|
|
}
|
|
|
|
ret = clk_set_rate(pltfm_host->clk, mmc->f_max);
|
|
if (ret) {
|
|
dev_err(dev, "failed to set clock to %d\n", mmc->f_max);
|
|
goto err_pltfm_free;
|
|
}
|
|
|
|
omap_host->pbias = devm_regulator_get_optional(dev, "pbias");
|
|
if (IS_ERR(omap_host->pbias)) {
|
|
ret = PTR_ERR(omap_host->pbias);
|
|
if (ret != -ENODEV)
|
|
goto err_pltfm_free;
|
|
dev_dbg(dev, "unable to get pbias regulator %d\n", ret);
|
|
}
|
|
omap_host->pbias_enabled = false;
|
|
|
|
/*
|
|
* omap_device_pm_domain has callbacks to enable the main
|
|
* functional clock, interface clock and also configure the
|
|
* SYSCONFIG register to clear any boot loader set voltage
|
|
* capabilities before calling sdhci_setup_host(). The
|
|
* callback will be invoked as part of pm_runtime_get_sync.
|
|
*/
|
|
pm_runtime_use_autosuspend(dev);
|
|
pm_runtime_set_autosuspend_delay(dev, 50);
|
|
pm_runtime_enable(dev);
|
|
ret = pm_runtime_resume_and_get(dev);
|
|
if (ret) {
|
|
dev_err(dev, "pm_runtime_get_sync failed\n");
|
|
goto err_rpm_disable;
|
|
}
|
|
|
|
ret = sdhci_omap_set_capabilities(host);
|
|
if (ret) {
|
|
dev_err(dev, "failed to set system capabilities\n");
|
|
goto err_rpm_put;
|
|
}
|
|
|
|
host->mmc_host_ops.start_signal_voltage_switch =
|
|
sdhci_omap_start_signal_voltage_switch;
|
|
host->mmc_host_ops.set_ios = sdhci_omap_set_ios;
|
|
host->mmc_host_ops.card_busy = sdhci_omap_card_busy;
|
|
host->mmc_host_ops.execute_tuning = sdhci_omap_execute_tuning;
|
|
host->mmc_host_ops.enable_sdio_irq = sdhci_omap_enable_sdio_irq;
|
|
|
|
/*
|
|
* Switch to external DMA only if there is the "dmas" property and
|
|
* ADMA is not available on the controller instance.
|
|
*/
|
|
if (device_property_present(dev, "dmas") &&
|
|
!sdhci_omap_has_adma(omap_host, offset))
|
|
sdhci_switch_external_dma(host, true);
|
|
|
|
if (device_property_read_bool(dev, "ti,non-removable")) {
|
|
dev_warn_once(dev, "using old ti,non-removable property\n");
|
|
mmc->caps |= MMC_CAP_NONREMOVABLE;
|
|
}
|
|
|
|
/* R1B responses is required to properly manage HW busy detection. */
|
|
mmc->caps |= MMC_CAP_NEED_RSP_BUSY;
|
|
|
|
/* Allow card power off and runtime PM for eMMC/SD card devices */
|
|
mmc->caps |= MMC_CAP_POWER_OFF_CARD | MMC_CAP_AGGRESSIVE_PM;
|
|
|
|
ret = sdhci_setup_host(host);
|
|
if (ret)
|
|
goto err_rpm_put;
|
|
|
|
ret = sdhci_omap_config_iodelay_pinctrl_state(omap_host);
|
|
if (ret)
|
|
goto err_cleanup_host;
|
|
|
|
ret = __sdhci_add_host(host);
|
|
if (ret)
|
|
goto err_cleanup_host;
|
|
|
|
/*
|
|
* SDIO devices can use the dat1 pin as a wake-up interrupt. Some
|
|
* devices like wl1xxx, use an out-of-band GPIO interrupt instead.
|
|
*/
|
|
omap_host->wakeirq = of_irq_get_byname(dev->of_node, "wakeup");
|
|
if (omap_host->wakeirq == -EPROBE_DEFER) {
|
|
ret = -EPROBE_DEFER;
|
|
goto err_cleanup_host;
|
|
}
|
|
if (omap_host->wakeirq > 0) {
|
|
device_init_wakeup(dev, true);
|
|
ret = dev_pm_set_dedicated_wake_irq(dev, omap_host->wakeirq);
|
|
if (ret) {
|
|
device_init_wakeup(dev, false);
|
|
goto err_cleanup_host;
|
|
}
|
|
host->mmc->pm_caps |= MMC_PM_KEEP_POWER | MMC_PM_WAKE_SDIO_IRQ;
|
|
}
|
|
|
|
pm_runtime_mark_last_busy(dev);
|
|
pm_runtime_put_autosuspend(dev);
|
|
|
|
return 0;
|
|
|
|
err_cleanup_host:
|
|
sdhci_cleanup_host(host);
|
|
|
|
err_rpm_put:
|
|
pm_runtime_mark_last_busy(dev);
|
|
pm_runtime_put_autosuspend(dev);
|
|
err_rpm_disable:
|
|
pm_runtime_dont_use_autosuspend(dev);
|
|
pm_runtime_disable(dev);
|
|
|
|
err_pltfm_free:
|
|
sdhci_pltfm_free(pdev);
|
|
return ret;
|
|
}
|
|
|
|
static int sdhci_omap_remove(struct platform_device *pdev)
|
|
{
|
|
struct device *dev = &pdev->dev;
|
|
struct sdhci_host *host = platform_get_drvdata(pdev);
|
|
|
|
pm_runtime_get_sync(dev);
|
|
sdhci_remove_host(host, true);
|
|
device_init_wakeup(dev, false);
|
|
dev_pm_clear_wake_irq(dev);
|
|
pm_runtime_dont_use_autosuspend(dev);
|
|
pm_runtime_put_sync(dev);
|
|
/* Ensure device gets disabled despite userspace sysfs config */
|
|
pm_runtime_force_suspend(dev);
|
|
sdhci_pltfm_free(pdev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
#ifdef CONFIG_PM
|
|
static void __maybe_unused sdhci_omap_context_save(struct sdhci_omap_host *omap_host)
|
|
{
|
|
omap_host->con = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
|
|
omap_host->hctl = sdhci_omap_readl(omap_host, SDHCI_OMAP_HCTL);
|
|
omap_host->sysctl = sdhci_omap_readl(omap_host, SDHCI_OMAP_SYSCTL);
|
|
omap_host->capa = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
|
|
omap_host->ie = sdhci_omap_readl(omap_host, SDHCI_OMAP_IE);
|
|
omap_host->ise = sdhci_omap_readl(omap_host, SDHCI_OMAP_ISE);
|
|
}
|
|
|
|
/* Order matters here, HCTL must be restored in two phases */
|
|
static void __maybe_unused sdhci_omap_context_restore(struct sdhci_omap_host *omap_host)
|
|
{
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_HCTL, omap_host->hctl);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CAPA, omap_host->capa);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_HCTL, omap_host->hctl);
|
|
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_SYSCTL, omap_host->sysctl);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, omap_host->con);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_IE, omap_host->ie);
|
|
sdhci_omap_writel(omap_host, SDHCI_OMAP_ISE, omap_host->ise);
|
|
}
|
|
|
|
static int __maybe_unused sdhci_omap_runtime_suspend(struct device *dev)
|
|
{
|
|
struct sdhci_host *host = dev_get_drvdata(dev);
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
if (omap_host->con != -EINVAL)
|
|
sdhci_runtime_suspend_host(host);
|
|
|
|
sdhci_omap_context_save(omap_host);
|
|
|
|
pinctrl_pm_select_idle_state(dev);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __maybe_unused sdhci_omap_runtime_resume(struct device *dev)
|
|
{
|
|
struct sdhci_host *host = dev_get_drvdata(dev);
|
|
struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
|
|
struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
|
|
|
|
pinctrl_pm_select_default_state(dev);
|
|
|
|
if (omap_host->con != -EINVAL) {
|
|
sdhci_omap_context_restore(omap_host);
|
|
sdhci_runtime_resume_host(host, 0);
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static const struct dev_pm_ops sdhci_omap_dev_pm_ops = {
|
|
SET_RUNTIME_PM_OPS(sdhci_omap_runtime_suspend,
|
|
sdhci_omap_runtime_resume, NULL)
|
|
SET_SYSTEM_SLEEP_PM_OPS(pm_runtime_force_suspend,
|
|
pm_runtime_force_resume)
|
|
};
|
|
|
|
static struct platform_driver sdhci_omap_driver = {
|
|
.probe = sdhci_omap_probe,
|
|
.remove = sdhci_omap_remove,
|
|
.driver = {
|
|
.name = "sdhci-omap",
|
|
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
|
|
.pm = &sdhci_omap_dev_pm_ops,
|
|
.of_match_table = omap_sdhci_match,
|
|
},
|
|
};
|
|
|
|
module_platform_driver(sdhci_omap_driver);
|
|
|
|
MODULE_DESCRIPTION("SDHCI driver for OMAP SoCs");
|
|
MODULE_AUTHOR("Texas Instruments Inc.");
|
|
MODULE_LICENSE("GPL v2");
|
|
MODULE_ALIAS("platform:sdhci_omap");
|