737 lines
17 KiB
C
737 lines
17 KiB
C
// SPDX-License-Identifier: GPL-2.0-only
|
|
/*
|
|
* Core Source for:
|
|
* Cypress TrueTouch(TM) Standard Product (TTSP) touchscreen drivers.
|
|
* For use with Cypress Txx3xx parts.
|
|
* Supported parts include:
|
|
* CY8CTST341
|
|
* CY8CTMA340
|
|
*
|
|
* Copyright (C) 2009, 2010, 2011 Cypress Semiconductor, Inc.
|
|
* Copyright (C) 2012 Javier Martinez Canillas <javier@dowhile0.org>
|
|
*
|
|
* Contact Cypress Semiconductor at www.cypress.com <kev@cypress.com>
|
|
*/
|
|
|
|
#include <linux/delay.h>
|
|
#include <linux/input.h>
|
|
#include <linux/input/mt.h>
|
|
#include <linux/input/touchscreen.h>
|
|
#include <linux/gpio.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/slab.h>
|
|
#include <linux/property.h>
|
|
#include <linux/gpio/consumer.h>
|
|
#include <linux/regulator/consumer.h>
|
|
|
|
#include "cyttsp_core.h"
|
|
|
|
/* Bootloader number of command keys */
|
|
#define CY_NUM_BL_KEYS 8
|
|
|
|
/* helpers */
|
|
#define GET_NUM_TOUCHES(x) ((x) & 0x0F)
|
|
#define IS_LARGE_AREA(x) (((x) & 0x10) >> 4)
|
|
#define IS_BAD_PKT(x) ((x) & 0x20)
|
|
#define IS_VALID_APP(x) ((x) & 0x01)
|
|
#define IS_OPERATIONAL_ERR(x) ((x) & 0x3F)
|
|
#define GET_HSTMODE(reg) (((reg) & 0x70) >> 4)
|
|
#define GET_BOOTLOADERMODE(reg) (((reg) & 0x10) >> 4)
|
|
|
|
#define CY_REG_BASE 0x00
|
|
#define CY_REG_ACT_DIST 0x1E
|
|
#define CY_REG_ACT_INTRVL 0x1D
|
|
#define CY_REG_TCH_TMOUT (CY_REG_ACT_INTRVL + 1)
|
|
#define CY_REG_LP_INTRVL (CY_REG_TCH_TMOUT + 1)
|
|
#define CY_MAXZ 255
|
|
#define CY_DELAY_DFLT 20 /* ms */
|
|
#define CY_DELAY_MAX 500
|
|
/* Active distance in pixels for a gesture to be reported */
|
|
#define CY_ACT_DIST_DFLT 0xF8 /* pixels */
|
|
#define CY_ACT_DIST_MASK 0x0F
|
|
/* Active Power state scanning/processing refresh interval */
|
|
#define CY_ACT_INTRVL_DFLT 0x00 /* ms */
|
|
/* Low Power state scanning/processing refresh interval */
|
|
#define CY_LP_INTRVL_DFLT 0x0A /* ms */
|
|
/* touch timeout for the Active power */
|
|
#define CY_TCH_TMOUT_DFLT 0xFF /* ms */
|
|
#define CY_HNDSHK_BIT 0x80
|
|
/* device mode bits */
|
|
#define CY_OPERATE_MODE 0x00
|
|
#define CY_SYSINFO_MODE 0x10
|
|
/* power mode select bits */
|
|
#define CY_SOFT_RESET_MODE 0x01 /* return to Bootloader mode */
|
|
#define CY_DEEP_SLEEP_MODE 0x02
|
|
#define CY_LOW_POWER_MODE 0x04
|
|
|
|
/* Slots management */
|
|
#define CY_MAX_FINGER 4
|
|
#define CY_MAX_ID 16
|
|
|
|
static const u8 bl_command[] = {
|
|
0x00, /* file offset */
|
|
0xFF, /* command */
|
|
0xA5, /* exit bootloader command */
|
|
0, 1, 2, 3, 4, 5, 6, 7 /* default keys */
|
|
};
|
|
|
|
static int ttsp_read_block_data(struct cyttsp *ts, u8 command,
|
|
u8 length, void *buf)
|
|
{
|
|
int error;
|
|
int tries;
|
|
|
|
for (tries = 0; tries < CY_NUM_RETRY; tries++) {
|
|
error = ts->bus_ops->read(ts->dev, ts->xfer_buf, command,
|
|
length, buf);
|
|
if (!error)
|
|
return 0;
|
|
|
|
msleep(CY_DELAY_DFLT);
|
|
}
|
|
|
|
return -EIO;
|
|
}
|
|
|
|
static int ttsp_write_block_data(struct cyttsp *ts, u8 command,
|
|
u8 length, void *buf)
|
|
{
|
|
int error;
|
|
int tries;
|
|
|
|
for (tries = 0; tries < CY_NUM_RETRY; tries++) {
|
|
error = ts->bus_ops->write(ts->dev, ts->xfer_buf, command,
|
|
length, buf);
|
|
if (!error)
|
|
return 0;
|
|
|
|
msleep(CY_DELAY_DFLT);
|
|
}
|
|
|
|
return -EIO;
|
|
}
|
|
|
|
static int ttsp_send_command(struct cyttsp *ts, u8 cmd)
|
|
{
|
|
return ttsp_write_block_data(ts, CY_REG_BASE, sizeof(cmd), &cmd);
|
|
}
|
|
|
|
static int cyttsp_handshake(struct cyttsp *ts)
|
|
{
|
|
if (ts->use_hndshk)
|
|
return ttsp_send_command(ts,
|
|
ts->xy_data.hst_mode ^ CY_HNDSHK_BIT);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cyttsp_load_bl_regs(struct cyttsp *ts)
|
|
{
|
|
memset(&ts->bl_data, 0, sizeof(ts->bl_data));
|
|
ts->bl_data.bl_status = 0x10;
|
|
|
|
return ttsp_read_block_data(ts, CY_REG_BASE,
|
|
sizeof(ts->bl_data), &ts->bl_data);
|
|
}
|
|
|
|
static int cyttsp_exit_bl_mode(struct cyttsp *ts)
|
|
{
|
|
int error;
|
|
u8 bl_cmd[sizeof(bl_command)];
|
|
|
|
memcpy(bl_cmd, bl_command, sizeof(bl_command));
|
|
if (ts->bl_keys)
|
|
memcpy(&bl_cmd[sizeof(bl_command) - CY_NUM_BL_KEYS],
|
|
ts->bl_keys, CY_NUM_BL_KEYS);
|
|
|
|
error = ttsp_write_block_data(ts, CY_REG_BASE,
|
|
sizeof(bl_cmd), bl_cmd);
|
|
if (error)
|
|
return error;
|
|
|
|
/* wait for TTSP Device to complete the operation */
|
|
msleep(CY_DELAY_DFLT);
|
|
|
|
error = cyttsp_load_bl_regs(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
if (GET_BOOTLOADERMODE(ts->bl_data.bl_status))
|
|
return -EIO;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cyttsp_set_operational_mode(struct cyttsp *ts)
|
|
{
|
|
int error;
|
|
|
|
error = ttsp_send_command(ts, CY_OPERATE_MODE);
|
|
if (error)
|
|
return error;
|
|
|
|
/* wait for TTSP Device to complete switch to Operational mode */
|
|
error = ttsp_read_block_data(ts, CY_REG_BASE,
|
|
sizeof(ts->xy_data), &ts->xy_data);
|
|
if (error)
|
|
return error;
|
|
|
|
error = cyttsp_handshake(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
return ts->xy_data.act_dist == CY_ACT_DIST_DFLT ? -EIO : 0;
|
|
}
|
|
|
|
static int cyttsp_set_sysinfo_mode(struct cyttsp *ts)
|
|
{
|
|
int error;
|
|
|
|
memset(&ts->sysinfo_data, 0, sizeof(ts->sysinfo_data));
|
|
|
|
/* switch to sysinfo mode */
|
|
error = ttsp_send_command(ts, CY_SYSINFO_MODE);
|
|
if (error)
|
|
return error;
|
|
|
|
/* read sysinfo registers */
|
|
msleep(CY_DELAY_DFLT);
|
|
error = ttsp_read_block_data(ts, CY_REG_BASE, sizeof(ts->sysinfo_data),
|
|
&ts->sysinfo_data);
|
|
if (error)
|
|
return error;
|
|
|
|
error = cyttsp_handshake(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
if (!ts->sysinfo_data.tts_verh && !ts->sysinfo_data.tts_verl)
|
|
return -EIO;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cyttsp_set_sysinfo_regs(struct cyttsp *ts)
|
|
{
|
|
int retval = 0;
|
|
|
|
if (ts->act_intrvl != CY_ACT_INTRVL_DFLT ||
|
|
ts->tch_tmout != CY_TCH_TMOUT_DFLT ||
|
|
ts->lp_intrvl != CY_LP_INTRVL_DFLT) {
|
|
|
|
u8 intrvl_ray[] = {
|
|
ts->act_intrvl,
|
|
ts->tch_tmout,
|
|
ts->lp_intrvl
|
|
};
|
|
|
|
/* set intrvl registers */
|
|
retval = ttsp_write_block_data(ts, CY_REG_ACT_INTRVL,
|
|
sizeof(intrvl_ray), intrvl_ray);
|
|
msleep(CY_DELAY_DFLT);
|
|
}
|
|
|
|
return retval;
|
|
}
|
|
|
|
static void cyttsp_hard_reset(struct cyttsp *ts)
|
|
{
|
|
if (ts->reset_gpio) {
|
|
/*
|
|
* According to the CY8CTMA340 datasheet page 21, the external
|
|
* reset pulse width should be >= 1 ms. The datasheet does not
|
|
* specify how long we have to wait after reset but a vendor
|
|
* tree specifies 5 ms here.
|
|
*/
|
|
gpiod_set_value_cansleep(ts->reset_gpio, 1);
|
|
usleep_range(1000, 2000);
|
|
gpiod_set_value_cansleep(ts->reset_gpio, 0);
|
|
usleep_range(5000, 6000);
|
|
}
|
|
}
|
|
|
|
static int cyttsp_soft_reset(struct cyttsp *ts)
|
|
{
|
|
int retval;
|
|
|
|
/* wait for interrupt to set ready completion */
|
|
reinit_completion(&ts->bl_ready);
|
|
ts->state = CY_BL_STATE;
|
|
|
|
enable_irq(ts->irq);
|
|
|
|
retval = ttsp_send_command(ts, CY_SOFT_RESET_MODE);
|
|
if (retval) {
|
|
dev_err(ts->dev, "failed to send soft reset\n");
|
|
goto out;
|
|
}
|
|
|
|
if (!wait_for_completion_timeout(&ts->bl_ready,
|
|
msecs_to_jiffies(CY_DELAY_DFLT * CY_DELAY_MAX))) {
|
|
dev_err(ts->dev, "timeout waiting for soft reset\n");
|
|
retval = -EIO;
|
|
}
|
|
|
|
out:
|
|
ts->state = CY_IDLE_STATE;
|
|
disable_irq(ts->irq);
|
|
return retval;
|
|
}
|
|
|
|
static int cyttsp_act_dist_setup(struct cyttsp *ts)
|
|
{
|
|
u8 act_dist_setup = ts->act_dist;
|
|
|
|
/* Init gesture; active distance setup */
|
|
return ttsp_write_block_data(ts, CY_REG_ACT_DIST,
|
|
sizeof(act_dist_setup), &act_dist_setup);
|
|
}
|
|
|
|
static void cyttsp_extract_track_ids(struct cyttsp_xydata *xy_data, int *ids)
|
|
{
|
|
ids[0] = xy_data->touch12_id >> 4;
|
|
ids[1] = xy_data->touch12_id & 0xF;
|
|
ids[2] = xy_data->touch34_id >> 4;
|
|
ids[3] = xy_data->touch34_id & 0xF;
|
|
}
|
|
|
|
static const struct cyttsp_tch *cyttsp_get_tch(struct cyttsp_xydata *xy_data,
|
|
int idx)
|
|
{
|
|
switch (idx) {
|
|
case 0:
|
|
return &xy_data->tch1;
|
|
case 1:
|
|
return &xy_data->tch2;
|
|
case 2:
|
|
return &xy_data->tch3;
|
|
case 3:
|
|
return &xy_data->tch4;
|
|
default:
|
|
return NULL;
|
|
}
|
|
}
|
|
|
|
static void cyttsp_report_tchdata(struct cyttsp *ts)
|
|
{
|
|
struct cyttsp_xydata *xy_data = &ts->xy_data;
|
|
struct input_dev *input = ts->input;
|
|
int num_tch = GET_NUM_TOUCHES(xy_data->tt_stat);
|
|
const struct cyttsp_tch *tch;
|
|
int ids[CY_MAX_ID];
|
|
int i;
|
|
DECLARE_BITMAP(used, CY_MAX_ID);
|
|
|
|
if (IS_LARGE_AREA(xy_data->tt_stat) == 1) {
|
|
/* terminate all active tracks */
|
|
num_tch = 0;
|
|
dev_dbg(ts->dev, "%s: Large area detected\n", __func__);
|
|
} else if (num_tch > CY_MAX_FINGER) {
|
|
/* terminate all active tracks */
|
|
num_tch = 0;
|
|
dev_dbg(ts->dev, "%s: Num touch error detected\n", __func__);
|
|
} else if (IS_BAD_PKT(xy_data->tt_mode)) {
|
|
/* terminate all active tracks */
|
|
num_tch = 0;
|
|
dev_dbg(ts->dev, "%s: Invalid buffer detected\n", __func__);
|
|
}
|
|
|
|
cyttsp_extract_track_ids(xy_data, ids);
|
|
|
|
bitmap_zero(used, CY_MAX_ID);
|
|
|
|
for (i = 0; i < num_tch; i++) {
|
|
tch = cyttsp_get_tch(xy_data, i);
|
|
|
|
input_mt_slot(input, ids[i]);
|
|
input_mt_report_slot_state(input, MT_TOOL_FINGER, true);
|
|
input_report_abs(input, ABS_MT_POSITION_X, be16_to_cpu(tch->x));
|
|
input_report_abs(input, ABS_MT_POSITION_Y, be16_to_cpu(tch->y));
|
|
input_report_abs(input, ABS_MT_TOUCH_MAJOR, tch->z);
|
|
|
|
__set_bit(ids[i], used);
|
|
}
|
|
|
|
for (i = 0; i < CY_MAX_ID; i++) {
|
|
if (test_bit(i, used))
|
|
continue;
|
|
|
|
input_mt_slot(input, i);
|
|
input_mt_report_slot_inactive(input);
|
|
}
|
|
|
|
input_sync(input);
|
|
}
|
|
|
|
static irqreturn_t cyttsp_irq(int irq, void *handle)
|
|
{
|
|
struct cyttsp *ts = handle;
|
|
int error;
|
|
|
|
if (unlikely(ts->state == CY_BL_STATE)) {
|
|
complete(&ts->bl_ready);
|
|
goto out;
|
|
}
|
|
|
|
/* Get touch data from CYTTSP device */
|
|
error = ttsp_read_block_data(ts, CY_REG_BASE,
|
|
sizeof(struct cyttsp_xydata), &ts->xy_data);
|
|
if (error)
|
|
goto out;
|
|
|
|
/* provide flow control handshake */
|
|
error = cyttsp_handshake(ts);
|
|
if (error)
|
|
goto out;
|
|
|
|
if (unlikely(ts->state == CY_IDLE_STATE))
|
|
goto out;
|
|
|
|
if (GET_BOOTLOADERMODE(ts->xy_data.tt_mode)) {
|
|
/*
|
|
* TTSP device has reset back to bootloader mode.
|
|
* Restore to operational mode.
|
|
*/
|
|
error = cyttsp_exit_bl_mode(ts);
|
|
if (error) {
|
|
dev_err(ts->dev,
|
|
"Could not return to operational mode, err: %d\n",
|
|
error);
|
|
ts->state = CY_IDLE_STATE;
|
|
}
|
|
} else {
|
|
cyttsp_report_tchdata(ts);
|
|
}
|
|
|
|
out:
|
|
return IRQ_HANDLED;
|
|
}
|
|
|
|
static int cyttsp_power_on(struct cyttsp *ts)
|
|
{
|
|
int error;
|
|
|
|
error = cyttsp_soft_reset(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
error = cyttsp_load_bl_regs(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
if (GET_BOOTLOADERMODE(ts->bl_data.bl_status) &&
|
|
IS_VALID_APP(ts->bl_data.bl_status)) {
|
|
error = cyttsp_exit_bl_mode(ts);
|
|
if (error) {
|
|
dev_err(ts->dev, "failed to exit bootloader mode\n");
|
|
return error;
|
|
}
|
|
}
|
|
|
|
if (GET_HSTMODE(ts->bl_data.bl_file) != CY_OPERATE_MODE ||
|
|
IS_OPERATIONAL_ERR(ts->bl_data.bl_status)) {
|
|
return -ENODEV;
|
|
}
|
|
|
|
error = cyttsp_set_sysinfo_mode(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
error = cyttsp_set_sysinfo_regs(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
error = cyttsp_set_operational_mode(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
/* init active distance */
|
|
error = cyttsp_act_dist_setup(ts);
|
|
if (error)
|
|
return error;
|
|
|
|
ts->state = CY_ACTIVE_STATE;
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cyttsp_enable(struct cyttsp *ts)
|
|
{
|
|
int error;
|
|
|
|
/*
|
|
* The device firmware can wake on an I2C or SPI memory slave
|
|
* address match. So just reading a register is sufficient to
|
|
* wake up the device. The first read attempt will fail but it
|
|
* will wake it up making the second read attempt successful.
|
|
*/
|
|
error = ttsp_read_block_data(ts, CY_REG_BASE,
|
|
sizeof(ts->xy_data), &ts->xy_data);
|
|
if (error)
|
|
return error;
|
|
|
|
if (GET_HSTMODE(ts->xy_data.hst_mode))
|
|
return -EIO;
|
|
|
|
enable_irq(ts->irq);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cyttsp_disable(struct cyttsp *ts)
|
|
{
|
|
int error;
|
|
|
|
error = ttsp_send_command(ts, CY_LOW_POWER_MODE);
|
|
if (error)
|
|
return error;
|
|
|
|
disable_irq(ts->irq);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int __maybe_unused cyttsp_suspend(struct device *dev)
|
|
{
|
|
struct cyttsp *ts = dev_get_drvdata(dev);
|
|
int retval = 0;
|
|
|
|
mutex_lock(&ts->input->mutex);
|
|
|
|
if (input_device_enabled(ts->input)) {
|
|
retval = cyttsp_disable(ts);
|
|
if (retval == 0)
|
|
ts->suspended = true;
|
|
}
|
|
|
|
mutex_unlock(&ts->input->mutex);
|
|
|
|
return retval;
|
|
}
|
|
|
|
static int __maybe_unused cyttsp_resume(struct device *dev)
|
|
{
|
|
struct cyttsp *ts = dev_get_drvdata(dev);
|
|
|
|
mutex_lock(&ts->input->mutex);
|
|
|
|
if (input_device_enabled(ts->input))
|
|
cyttsp_enable(ts);
|
|
|
|
ts->suspended = false;
|
|
|
|
mutex_unlock(&ts->input->mutex);
|
|
|
|
return 0;
|
|
}
|
|
|
|
SIMPLE_DEV_PM_OPS(cyttsp_pm_ops, cyttsp_suspend, cyttsp_resume);
|
|
EXPORT_SYMBOL_GPL(cyttsp_pm_ops);
|
|
|
|
static int cyttsp_open(struct input_dev *dev)
|
|
{
|
|
struct cyttsp *ts = input_get_drvdata(dev);
|
|
int retval = 0;
|
|
|
|
if (!ts->suspended)
|
|
retval = cyttsp_enable(ts);
|
|
|
|
return retval;
|
|
}
|
|
|
|
static void cyttsp_close(struct input_dev *dev)
|
|
{
|
|
struct cyttsp *ts = input_get_drvdata(dev);
|
|
|
|
if (!ts->suspended)
|
|
cyttsp_disable(ts);
|
|
}
|
|
|
|
static int cyttsp_parse_properties(struct cyttsp *ts)
|
|
{
|
|
struct device *dev = ts->dev;
|
|
u32 dt_value;
|
|
int ret;
|
|
|
|
ts->bl_keys = devm_kzalloc(dev, CY_NUM_BL_KEYS, GFP_KERNEL);
|
|
if (!ts->bl_keys)
|
|
return -ENOMEM;
|
|
|
|
/* Set some default values */
|
|
ts->use_hndshk = false;
|
|
ts->act_dist = CY_ACT_DIST_DFLT;
|
|
ts->act_intrvl = CY_ACT_INTRVL_DFLT;
|
|
ts->tch_tmout = CY_TCH_TMOUT_DFLT;
|
|
ts->lp_intrvl = CY_LP_INTRVL_DFLT;
|
|
|
|
ret = device_property_read_u8_array(dev, "bootloader-key",
|
|
ts->bl_keys, CY_NUM_BL_KEYS);
|
|
if (ret) {
|
|
dev_err(dev,
|
|
"bootloader-key property could not be retrieved\n");
|
|
return ret;
|
|
}
|
|
|
|
ts->use_hndshk = device_property_present(dev, "use-handshake");
|
|
|
|
if (!device_property_read_u32(dev, "active-distance", &dt_value)) {
|
|
if (dt_value > 15) {
|
|
dev_err(dev, "active-distance (%u) must be [0-15]\n",
|
|
dt_value);
|
|
return -EINVAL;
|
|
}
|
|
ts->act_dist &= ~CY_ACT_DIST_MASK;
|
|
ts->act_dist |= dt_value;
|
|
}
|
|
|
|
if (!device_property_read_u32(dev, "active-interval-ms", &dt_value)) {
|
|
if (dt_value > 255) {
|
|
dev_err(dev, "active-interval-ms (%u) must be [0-255]\n",
|
|
dt_value);
|
|
return -EINVAL;
|
|
}
|
|
ts->act_intrvl = dt_value;
|
|
}
|
|
|
|
if (!device_property_read_u32(dev, "lowpower-interval-ms", &dt_value)) {
|
|
if (dt_value > 2550) {
|
|
dev_err(dev, "lowpower-interval-ms (%u) must be [0-2550]\n",
|
|
dt_value);
|
|
return -EINVAL;
|
|
}
|
|
/* Register value is expressed in 0.01s / bit */
|
|
ts->lp_intrvl = dt_value / 10;
|
|
}
|
|
|
|
if (!device_property_read_u32(dev, "touch-timeout-ms", &dt_value)) {
|
|
if (dt_value > 2550) {
|
|
dev_err(dev, "touch-timeout-ms (%u) must be [0-2550]\n",
|
|
dt_value);
|
|
return -EINVAL;
|
|
}
|
|
/* Register value is expressed in 0.01s / bit */
|
|
ts->tch_tmout = dt_value / 10;
|
|
}
|
|
|
|
return 0;
|
|
}
|
|
|
|
static void cyttsp_disable_regulators(void *_ts)
|
|
{
|
|
struct cyttsp *ts = _ts;
|
|
|
|
regulator_bulk_disable(ARRAY_SIZE(ts->regulators),
|
|
ts->regulators);
|
|
}
|
|
|
|
struct cyttsp *cyttsp_probe(const struct cyttsp_bus_ops *bus_ops,
|
|
struct device *dev, int irq, size_t xfer_buf_size)
|
|
{
|
|
struct cyttsp *ts;
|
|
struct input_dev *input_dev;
|
|
int error;
|
|
|
|
ts = devm_kzalloc(dev, sizeof(*ts) + xfer_buf_size, GFP_KERNEL);
|
|
if (!ts)
|
|
return ERR_PTR(-ENOMEM);
|
|
|
|
input_dev = devm_input_allocate_device(dev);
|
|
if (!input_dev)
|
|
return ERR_PTR(-ENOMEM);
|
|
|
|
ts->dev = dev;
|
|
ts->input = input_dev;
|
|
ts->bus_ops = bus_ops;
|
|
ts->irq = irq;
|
|
|
|
/*
|
|
* VCPIN is the analog voltage supply
|
|
* VDD is the digital voltage supply
|
|
*/
|
|
ts->regulators[0].supply = "vcpin";
|
|
ts->regulators[1].supply = "vdd";
|
|
error = devm_regulator_bulk_get(dev, ARRAY_SIZE(ts->regulators),
|
|
ts->regulators);
|
|
if (error) {
|
|
dev_err(dev, "Failed to get regulators: %d\n", error);
|
|
return ERR_PTR(error);
|
|
}
|
|
|
|
error = regulator_bulk_enable(ARRAY_SIZE(ts->regulators),
|
|
ts->regulators);
|
|
if (error) {
|
|
dev_err(dev, "Cannot enable regulators: %d\n", error);
|
|
return ERR_PTR(error);
|
|
}
|
|
|
|
error = devm_add_action_or_reset(dev, cyttsp_disable_regulators, ts);
|
|
if (error) {
|
|
dev_err(dev, "failed to install chip disable handler\n");
|
|
return ERR_PTR(error);
|
|
}
|
|
|
|
ts->reset_gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
|
|
if (IS_ERR(ts->reset_gpio)) {
|
|
error = PTR_ERR(ts->reset_gpio);
|
|
dev_err(dev, "Failed to request reset gpio, error %d\n", error);
|
|
return ERR_PTR(error);
|
|
}
|
|
|
|
error = cyttsp_parse_properties(ts);
|
|
if (error)
|
|
return ERR_PTR(error);
|
|
|
|
init_completion(&ts->bl_ready);
|
|
|
|
input_dev->name = "Cypress TTSP TouchScreen";
|
|
input_dev->id.bustype = bus_ops->bustype;
|
|
input_dev->dev.parent = ts->dev;
|
|
|
|
input_dev->open = cyttsp_open;
|
|
input_dev->close = cyttsp_close;
|
|
|
|
input_set_drvdata(input_dev, ts);
|
|
|
|
input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_X);
|
|
input_set_capability(input_dev, EV_ABS, ABS_MT_POSITION_Y);
|
|
/* One byte for width 0..255 so this is the limit */
|
|
input_set_abs_params(input_dev, ABS_MT_TOUCH_MAJOR, 0, 255, 0, 0);
|
|
|
|
touchscreen_parse_properties(input_dev, true, NULL);
|
|
|
|
error = input_mt_init_slots(input_dev, CY_MAX_ID, INPUT_MT_DIRECT);
|
|
if (error) {
|
|
dev_err(dev, "Unable to init MT slots.\n");
|
|
return ERR_PTR(error);
|
|
}
|
|
|
|
error = devm_request_threaded_irq(dev, ts->irq, NULL, cyttsp_irq,
|
|
IRQF_ONESHOT | IRQF_NO_AUTOEN,
|
|
"cyttsp", ts);
|
|
if (error) {
|
|
dev_err(ts->dev, "failed to request IRQ %d, err: %d\n",
|
|
ts->irq, error);
|
|
return ERR_PTR(error);
|
|
}
|
|
|
|
cyttsp_hard_reset(ts);
|
|
|
|
error = cyttsp_power_on(ts);
|
|
if (error)
|
|
return ERR_PTR(error);
|
|
|
|
error = input_register_device(input_dev);
|
|
if (error) {
|
|
dev_err(ts->dev, "failed to register input device: %d\n",
|
|
error);
|
|
return ERR_PTR(error);
|
|
}
|
|
|
|
return ts;
|
|
}
|
|
EXPORT_SYMBOL_GPL(cyttsp_probe);
|
|
|
|
MODULE_LICENSE("GPL");
|
|
MODULE_DESCRIPTION("Cypress TrueTouch(R) Standard touchscreen driver core");
|
|
MODULE_AUTHOR("Cypress");
|