1399 lines
39 KiB
C
1399 lines
39 KiB
C
// SPDX-License-Identifier: GPL-2.0-or-later
|
|
/*
|
|
* I2C bus driver for the Cadence I2C controller.
|
|
*
|
|
* Copyright (C) 2009 - 2014 Xilinx, Inc.
|
|
*/
|
|
|
|
#include <linux/clk.h>
|
|
#include <linux/delay.h>
|
|
#include <linux/i2c.h>
|
|
#include <linux/interrupt.h>
|
|
#include <linux/io.h>
|
|
#include <linux/iopoll.h>
|
|
#include <linux/module.h>
|
|
#include <linux/platform_device.h>
|
|
#include <linux/of.h>
|
|
#include <linux/pm_runtime.h>
|
|
#include <linux/pinctrl/consumer.h>
|
|
|
|
/* Register offsets for the I2C device. */
|
|
#define CDNS_I2C_CR_OFFSET 0x00 /* Control Register, RW */
|
|
#define CDNS_I2C_SR_OFFSET 0x04 /* Status Register, RO */
|
|
#define CDNS_I2C_ADDR_OFFSET 0x08 /* I2C Address Register, RW */
|
|
#define CDNS_I2C_DATA_OFFSET 0x0C /* I2C Data Register, RW */
|
|
#define CDNS_I2C_ISR_OFFSET 0x10 /* IRQ Status Register, RW */
|
|
#define CDNS_I2C_XFER_SIZE_OFFSET 0x14 /* Transfer Size Register, RW */
|
|
#define CDNS_I2C_TIME_OUT_OFFSET 0x1C /* Time Out Register, RW */
|
|
#define CDNS_I2C_IMR_OFFSET 0x20 /* IRQ Mask Register, RO */
|
|
#define CDNS_I2C_IER_OFFSET 0x24 /* IRQ Enable Register, WO */
|
|
#define CDNS_I2C_IDR_OFFSET 0x28 /* IRQ Disable Register, WO */
|
|
|
|
/* Control Register Bit mask definitions */
|
|
#define CDNS_I2C_CR_HOLD BIT(4) /* Hold Bus bit */
|
|
#define CDNS_I2C_CR_ACK_EN BIT(3)
|
|
#define CDNS_I2C_CR_NEA BIT(2)
|
|
#define CDNS_I2C_CR_MS BIT(1)
|
|
/* Read or Write Master transfer 0 = Transmitter, 1 = Receiver */
|
|
#define CDNS_I2C_CR_RW BIT(0)
|
|
/* 1 = Auto init FIFO to zeroes */
|
|
#define CDNS_I2C_CR_CLR_FIFO BIT(6)
|
|
#define CDNS_I2C_CR_DIVA_SHIFT 14
|
|
#define CDNS_I2C_CR_DIVA_MASK (3 << CDNS_I2C_CR_DIVA_SHIFT)
|
|
#define CDNS_I2C_CR_DIVB_SHIFT 8
|
|
#define CDNS_I2C_CR_DIVB_MASK (0x3f << CDNS_I2C_CR_DIVB_SHIFT)
|
|
|
|
#define CDNS_I2C_CR_MASTER_EN_MASK (CDNS_I2C_CR_NEA | \
|
|
CDNS_I2C_CR_ACK_EN | \
|
|
CDNS_I2C_CR_MS)
|
|
|
|
#define CDNS_I2C_CR_SLAVE_EN_MASK ~CDNS_I2C_CR_MASTER_EN_MASK
|
|
|
|
/* Status Register Bit mask definitions */
|
|
#define CDNS_I2C_SR_BA BIT(8)
|
|
#define CDNS_I2C_SR_TXDV BIT(6)
|
|
#define CDNS_I2C_SR_RXDV BIT(5)
|
|
#define CDNS_I2C_SR_RXRW BIT(3)
|
|
|
|
/*
|
|
* I2C Address Register Bit mask definitions
|
|
* Normal addressing mode uses [6:0] bits. Extended addressing mode uses [9:0]
|
|
* bits. A write access to this register always initiates a transfer if the I2C
|
|
* is in master mode.
|
|
*/
|
|
#define CDNS_I2C_ADDR_MASK 0x000003FF /* I2C Address Mask */
|
|
|
|
/*
|
|
* I2C Interrupt Registers Bit mask definitions
|
|
* All the four interrupt registers (Status/Mask/Enable/Disable) have the same
|
|
* bit definitions.
|
|
*/
|
|
#define CDNS_I2C_IXR_ARB_LOST BIT(9)
|
|
#define CDNS_I2C_IXR_RX_UNF BIT(7)
|
|
#define CDNS_I2C_IXR_TX_OVF BIT(6)
|
|
#define CDNS_I2C_IXR_RX_OVF BIT(5)
|
|
#define CDNS_I2C_IXR_SLV_RDY BIT(4)
|
|
#define CDNS_I2C_IXR_TO BIT(3)
|
|
#define CDNS_I2C_IXR_NACK BIT(2)
|
|
#define CDNS_I2C_IXR_DATA BIT(1)
|
|
#define CDNS_I2C_IXR_COMP BIT(0)
|
|
|
|
#define CDNS_I2C_IXR_ALL_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \
|
|
CDNS_I2C_IXR_RX_UNF | \
|
|
CDNS_I2C_IXR_TX_OVF | \
|
|
CDNS_I2C_IXR_RX_OVF | \
|
|
CDNS_I2C_IXR_SLV_RDY | \
|
|
CDNS_I2C_IXR_TO | \
|
|
CDNS_I2C_IXR_NACK | \
|
|
CDNS_I2C_IXR_DATA | \
|
|
CDNS_I2C_IXR_COMP)
|
|
|
|
#define CDNS_I2C_IXR_ERR_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \
|
|
CDNS_I2C_IXR_RX_UNF | \
|
|
CDNS_I2C_IXR_TX_OVF | \
|
|
CDNS_I2C_IXR_RX_OVF | \
|
|
CDNS_I2C_IXR_NACK)
|
|
|
|
#define CDNS_I2C_ENABLED_INTR_MASK (CDNS_I2C_IXR_ARB_LOST | \
|
|
CDNS_I2C_IXR_RX_UNF | \
|
|
CDNS_I2C_IXR_TX_OVF | \
|
|
CDNS_I2C_IXR_RX_OVF | \
|
|
CDNS_I2C_IXR_NACK | \
|
|
CDNS_I2C_IXR_DATA | \
|
|
CDNS_I2C_IXR_COMP)
|
|
|
|
#define CDNS_I2C_IXR_SLAVE_INTR_MASK (CDNS_I2C_IXR_RX_UNF | \
|
|
CDNS_I2C_IXR_TX_OVF | \
|
|
CDNS_I2C_IXR_RX_OVF | \
|
|
CDNS_I2C_IXR_TO | \
|
|
CDNS_I2C_IXR_NACK | \
|
|
CDNS_I2C_IXR_DATA | \
|
|
CDNS_I2C_IXR_COMP)
|
|
|
|
#define CDNS_I2C_TIMEOUT msecs_to_jiffies(1000)
|
|
/* timeout for pm runtime autosuspend */
|
|
#define CNDS_I2C_PM_TIMEOUT 1000 /* ms */
|
|
|
|
#define CDNS_I2C_FIFO_DEPTH 16
|
|
/* FIFO depth at which the DATA interrupt occurs */
|
|
#define CDNS_I2C_DATA_INTR_DEPTH (CDNS_I2C_FIFO_DEPTH - 2)
|
|
#define CDNS_I2C_MAX_TRANSFER_SIZE 255
|
|
/* Transfer size in multiples of data interrupt depth */
|
|
#define CDNS_I2C_TRANSFER_SIZE (CDNS_I2C_MAX_TRANSFER_SIZE - 3)
|
|
|
|
#define DRIVER_NAME "cdns-i2c"
|
|
|
|
#define CDNS_I2C_DIVA_MAX 4
|
|
#define CDNS_I2C_DIVB_MAX 64
|
|
|
|
#define CDNS_I2C_TIMEOUT_MAX 0xFF
|
|
|
|
#define CDNS_I2C_BROKEN_HOLD_BIT BIT(0)
|
|
#define CDNS_I2C_POLL_US 100000
|
|
#define CDNS_I2C_TIMEOUT_US 500000
|
|
|
|
#define cdns_i2c_readreg(offset) readl_relaxed(id->membase + offset)
|
|
#define cdns_i2c_writereg(val, offset) writel_relaxed(val, id->membase + offset)
|
|
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
/**
|
|
* enum cdns_i2c_mode - I2C Controller current operating mode
|
|
*
|
|
* @CDNS_I2C_MODE_SLAVE: I2C controller operating in slave mode
|
|
* @CDNS_I2C_MODE_MASTER: I2C Controller operating in master mode
|
|
*/
|
|
enum cdns_i2c_mode {
|
|
CDNS_I2C_MODE_SLAVE,
|
|
CDNS_I2C_MODE_MASTER,
|
|
};
|
|
|
|
/**
|
|
* enum cdns_i2c_slave_state - Slave state when I2C is operating in slave mode
|
|
*
|
|
* @CDNS_I2C_SLAVE_STATE_IDLE: I2C slave idle
|
|
* @CDNS_I2C_SLAVE_STATE_SEND: I2C slave sending data to master
|
|
* @CDNS_I2C_SLAVE_STATE_RECV: I2C slave receiving data from master
|
|
*/
|
|
enum cdns_i2c_slave_state {
|
|
CDNS_I2C_SLAVE_STATE_IDLE,
|
|
CDNS_I2C_SLAVE_STATE_SEND,
|
|
CDNS_I2C_SLAVE_STATE_RECV,
|
|
};
|
|
#endif
|
|
|
|
/**
|
|
* struct cdns_i2c - I2C device private data structure
|
|
*
|
|
* @dev: Pointer to device structure
|
|
* @membase: Base address of the I2C device
|
|
* @adap: I2C adapter instance
|
|
* @p_msg: Message pointer
|
|
* @err_status: Error status in Interrupt Status Register
|
|
* @xfer_done: Transfer complete status
|
|
* @p_send_buf: Pointer to transmit buffer
|
|
* @p_recv_buf: Pointer to receive buffer
|
|
* @send_count: Number of bytes still expected to send
|
|
* @recv_count: Number of bytes still expected to receive
|
|
* @curr_recv_count: Number of bytes to be received in current transfer
|
|
* @irq: IRQ number
|
|
* @input_clk: Input clock to I2C controller
|
|
* @i2c_clk: Maximum I2C clock speed
|
|
* @bus_hold_flag: Flag used in repeated start for clearing HOLD bit
|
|
* @clk: Pointer to struct clk
|
|
* @clk_rate_change_nb: Notifier block for clock rate changes
|
|
* @quirks: flag for broken hold bit usage in r1p10
|
|
* @ctrl_reg: Cached value of the control register.
|
|
* @ctrl_reg_diva_divb: value of fields DIV_A and DIV_B from CR register
|
|
* @slave: Registered slave instance.
|
|
* @dev_mode: I2C operating role(master/slave).
|
|
* @slave_state: I2C Slave state(idle/read/write).
|
|
*/
|
|
struct cdns_i2c {
|
|
struct device *dev;
|
|
void __iomem *membase;
|
|
struct i2c_adapter adap;
|
|
struct i2c_msg *p_msg;
|
|
int err_status;
|
|
struct completion xfer_done;
|
|
unsigned char *p_send_buf;
|
|
unsigned char *p_recv_buf;
|
|
unsigned int send_count;
|
|
unsigned int recv_count;
|
|
unsigned int curr_recv_count;
|
|
int irq;
|
|
unsigned long input_clk;
|
|
unsigned int i2c_clk;
|
|
unsigned int bus_hold_flag;
|
|
struct clk *clk;
|
|
struct notifier_block clk_rate_change_nb;
|
|
u32 quirks;
|
|
u32 ctrl_reg;
|
|
struct i2c_bus_recovery_info rinfo;
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
u16 ctrl_reg_diva_divb;
|
|
struct i2c_client *slave;
|
|
enum cdns_i2c_mode dev_mode;
|
|
enum cdns_i2c_slave_state slave_state;
|
|
#endif
|
|
};
|
|
|
|
struct cdns_platform_data {
|
|
u32 quirks;
|
|
};
|
|
|
|
#define to_cdns_i2c(_nb) container_of(_nb, struct cdns_i2c, \
|
|
clk_rate_change_nb)
|
|
|
|
/**
|
|
* cdns_i2c_clear_bus_hold - Clear bus hold bit
|
|
* @id: Pointer to driver data struct
|
|
*
|
|
* Helper to clear the controller's bus hold bit.
|
|
*/
|
|
static void cdns_i2c_clear_bus_hold(struct cdns_i2c *id)
|
|
{
|
|
u32 reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
|
|
if (reg & CDNS_I2C_CR_HOLD)
|
|
cdns_i2c_writereg(reg & ~CDNS_I2C_CR_HOLD, CDNS_I2C_CR_OFFSET);
|
|
}
|
|
|
|
static inline bool cdns_is_holdquirk(struct cdns_i2c *id, bool hold_wrkaround)
|
|
{
|
|
return (hold_wrkaround &&
|
|
(id->curr_recv_count == CDNS_I2C_FIFO_DEPTH + 1));
|
|
}
|
|
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
static void cdns_i2c_set_mode(enum cdns_i2c_mode mode, struct cdns_i2c *id)
|
|
{
|
|
/* Disable all interrupts */
|
|
cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET);
|
|
|
|
/* Clear FIFO and transfer size */
|
|
cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET);
|
|
|
|
/* Update device mode and state */
|
|
id->dev_mode = mode;
|
|
id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
|
|
|
|
switch (mode) {
|
|
case CDNS_I2C_MODE_MASTER:
|
|
/* Enable i2c master */
|
|
cdns_i2c_writereg(id->ctrl_reg_diva_divb |
|
|
CDNS_I2C_CR_MASTER_EN_MASK,
|
|
CDNS_I2C_CR_OFFSET);
|
|
/*
|
|
* This delay is needed to give the IP some time to switch to
|
|
* the master mode. With lower values(like 110 us) i2cdetect
|
|
* will not detect any slave and without this delay, the IP will
|
|
* trigger a timeout interrupt.
|
|
*/
|
|
usleep_range(115, 125);
|
|
break;
|
|
case CDNS_I2C_MODE_SLAVE:
|
|
/* Enable i2c slave */
|
|
cdns_i2c_writereg(id->ctrl_reg_diva_divb &
|
|
CDNS_I2C_CR_SLAVE_EN_MASK,
|
|
CDNS_I2C_CR_OFFSET);
|
|
|
|
/* Setting slave address */
|
|
cdns_i2c_writereg(id->slave->addr & CDNS_I2C_ADDR_MASK,
|
|
CDNS_I2C_ADDR_OFFSET);
|
|
|
|
/* Enable slave send/receive interrupts */
|
|
cdns_i2c_writereg(CDNS_I2C_IXR_SLAVE_INTR_MASK,
|
|
CDNS_I2C_IER_OFFSET);
|
|
break;
|
|
}
|
|
}
|
|
|
|
static void cdns_i2c_slave_rcv_data(struct cdns_i2c *id)
|
|
{
|
|
u8 bytes;
|
|
unsigned char data;
|
|
|
|
/* Prepare backend for data reception */
|
|
if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) {
|
|
id->slave_state = CDNS_I2C_SLAVE_STATE_RECV;
|
|
i2c_slave_event(id->slave, I2C_SLAVE_WRITE_REQUESTED, NULL);
|
|
}
|
|
|
|
/* Fetch number of bytes to receive */
|
|
bytes = cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
|
|
|
|
/* Read data and send to backend */
|
|
while (bytes--) {
|
|
data = cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
|
|
i2c_slave_event(id->slave, I2C_SLAVE_WRITE_RECEIVED, &data);
|
|
}
|
|
}
|
|
|
|
static void cdns_i2c_slave_send_data(struct cdns_i2c *id)
|
|
{
|
|
u8 data;
|
|
|
|
/* Prepare backend for data transmission */
|
|
if (id->slave_state == CDNS_I2C_SLAVE_STATE_IDLE) {
|
|
id->slave_state = CDNS_I2C_SLAVE_STATE_SEND;
|
|
i2c_slave_event(id->slave, I2C_SLAVE_READ_REQUESTED, &data);
|
|
} else {
|
|
i2c_slave_event(id->slave, I2C_SLAVE_READ_PROCESSED, &data);
|
|
}
|
|
|
|
/* Send data over bus */
|
|
cdns_i2c_writereg(data, CDNS_I2C_DATA_OFFSET);
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_slave_isr - Interrupt handler for the I2C device in slave role
|
|
* @ptr: Pointer to I2C device private data
|
|
*
|
|
* This function handles the data interrupt and transfer complete interrupt of
|
|
* the I2C device in slave role.
|
|
*
|
|
* Return: IRQ_HANDLED always
|
|
*/
|
|
static irqreturn_t cdns_i2c_slave_isr(void *ptr)
|
|
{
|
|
struct cdns_i2c *id = ptr;
|
|
unsigned int isr_status, i2c_status;
|
|
|
|
/* Fetch the interrupt status */
|
|
isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
|
|
cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
|
|
|
|
/* Ignore masked interrupts */
|
|
isr_status &= ~cdns_i2c_readreg(CDNS_I2C_IMR_OFFSET);
|
|
|
|
/* Fetch transfer mode (send/receive) */
|
|
i2c_status = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET);
|
|
|
|
/* Handle data send/receive */
|
|
if (i2c_status & CDNS_I2C_SR_RXRW) {
|
|
/* Send data to master */
|
|
if (isr_status & CDNS_I2C_IXR_DATA)
|
|
cdns_i2c_slave_send_data(id);
|
|
|
|
if (isr_status & CDNS_I2C_IXR_COMP) {
|
|
id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
|
|
i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
|
|
}
|
|
} else {
|
|
/* Receive data from master */
|
|
if (isr_status & CDNS_I2C_IXR_DATA)
|
|
cdns_i2c_slave_rcv_data(id);
|
|
|
|
if (isr_status & CDNS_I2C_IXR_COMP) {
|
|
cdns_i2c_slave_rcv_data(id);
|
|
id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
|
|
i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
|
|
}
|
|
}
|
|
|
|
/* Master indicated xfer stop or fifo underflow/overflow */
|
|
if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_RX_OVF |
|
|
CDNS_I2C_IXR_RX_UNF | CDNS_I2C_IXR_TX_OVF)) {
|
|
id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
|
|
i2c_slave_event(id->slave, I2C_SLAVE_STOP, NULL);
|
|
cdns_i2c_writereg(CDNS_I2C_CR_CLR_FIFO, CDNS_I2C_CR_OFFSET);
|
|
}
|
|
|
|
return IRQ_HANDLED;
|
|
}
|
|
#endif
|
|
|
|
/**
|
|
* cdns_i2c_master_isr - Interrupt handler for the I2C device in master role
|
|
* @ptr: Pointer to I2C device private data
|
|
*
|
|
* This function handles the data interrupt, transfer complete interrupt and
|
|
* the error interrupts of the I2C device in master role.
|
|
*
|
|
* Return: IRQ_HANDLED always
|
|
*/
|
|
static irqreturn_t cdns_i2c_master_isr(void *ptr)
|
|
{
|
|
unsigned int isr_status, avail_bytes;
|
|
unsigned int bytes_to_send;
|
|
bool updatetx;
|
|
struct cdns_i2c *id = ptr;
|
|
/* Signal completion only after everything is updated */
|
|
int done_flag = 0;
|
|
irqreturn_t status = IRQ_NONE;
|
|
|
|
isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
|
|
cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
|
|
id->err_status = 0;
|
|
|
|
/* Handling nack and arbitration lost interrupt */
|
|
if (isr_status & (CDNS_I2C_IXR_NACK | CDNS_I2C_IXR_ARB_LOST)) {
|
|
done_flag = 1;
|
|
status = IRQ_HANDLED;
|
|
}
|
|
|
|
/*
|
|
* Check if transfer size register needs to be updated again for a
|
|
* large data receive operation.
|
|
*/
|
|
updatetx = id->recv_count > id->curr_recv_count;
|
|
|
|
/* When receiving, handle data interrupt and completion interrupt */
|
|
if (id->p_recv_buf &&
|
|
((isr_status & CDNS_I2C_IXR_COMP) ||
|
|
(isr_status & CDNS_I2C_IXR_DATA))) {
|
|
/* Read data if receive data valid is set */
|
|
while (cdns_i2c_readreg(CDNS_I2C_SR_OFFSET) &
|
|
CDNS_I2C_SR_RXDV) {
|
|
if (id->recv_count > 0) {
|
|
*(id->p_recv_buf)++ =
|
|
cdns_i2c_readreg(CDNS_I2C_DATA_OFFSET);
|
|
id->recv_count--;
|
|
id->curr_recv_count--;
|
|
|
|
/*
|
|
* Clear hold bit that was set for FIFO control
|
|
* if RX data left is less than or equal to
|
|
* FIFO DEPTH unless repeated start is selected
|
|
*/
|
|
if (id->recv_count <= CDNS_I2C_FIFO_DEPTH &&
|
|
!id->bus_hold_flag)
|
|
cdns_i2c_clear_bus_hold(id);
|
|
|
|
} else {
|
|
dev_err(id->adap.dev.parent,
|
|
"xfer_size reg rollover. xfer aborted!\n");
|
|
id->err_status |= CDNS_I2C_IXR_TO;
|
|
break;
|
|
}
|
|
|
|
if (cdns_is_holdquirk(id, updatetx))
|
|
break;
|
|
}
|
|
|
|
/*
|
|
* The controller sends NACK to the slave when transfer size
|
|
* register reaches zero without considering the HOLD bit.
|
|
* This workaround is implemented for large data transfers to
|
|
* maintain transfer size non-zero while performing a large
|
|
* receive operation.
|
|
*/
|
|
if (cdns_is_holdquirk(id, updatetx)) {
|
|
/* wait while fifo is full */
|
|
while (cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET) !=
|
|
(id->curr_recv_count - CDNS_I2C_FIFO_DEPTH))
|
|
;
|
|
|
|
/*
|
|
* Check number of bytes to be received against maximum
|
|
* transfer size and update register accordingly.
|
|
*/
|
|
if (((int)(id->recv_count) - CDNS_I2C_FIFO_DEPTH) >
|
|
CDNS_I2C_TRANSFER_SIZE) {
|
|
cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
|
|
CDNS_I2C_XFER_SIZE_OFFSET);
|
|
id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE +
|
|
CDNS_I2C_FIFO_DEPTH;
|
|
} else {
|
|
cdns_i2c_writereg(id->recv_count -
|
|
CDNS_I2C_FIFO_DEPTH,
|
|
CDNS_I2C_XFER_SIZE_OFFSET);
|
|
id->curr_recv_count = id->recv_count;
|
|
}
|
|
}
|
|
|
|
/* Clear hold (if not repeated start) and signal completion */
|
|
if ((isr_status & CDNS_I2C_IXR_COMP) && !id->recv_count) {
|
|
if (!id->bus_hold_flag)
|
|
cdns_i2c_clear_bus_hold(id);
|
|
done_flag = 1;
|
|
}
|
|
|
|
status = IRQ_HANDLED;
|
|
}
|
|
|
|
/* When sending, handle transfer complete interrupt */
|
|
if ((isr_status & CDNS_I2C_IXR_COMP) && !id->p_recv_buf) {
|
|
/*
|
|
* If there is more data to be sent, calculate the
|
|
* space available in FIFO and fill with that many bytes.
|
|
*/
|
|
if (id->send_count) {
|
|
avail_bytes = CDNS_I2C_FIFO_DEPTH -
|
|
cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
|
|
if (id->send_count > avail_bytes)
|
|
bytes_to_send = avail_bytes;
|
|
else
|
|
bytes_to_send = id->send_count;
|
|
|
|
while (bytes_to_send--) {
|
|
cdns_i2c_writereg(
|
|
(*(id->p_send_buf)++),
|
|
CDNS_I2C_DATA_OFFSET);
|
|
id->send_count--;
|
|
}
|
|
} else {
|
|
/*
|
|
* Signal the completion of transaction and
|
|
* clear the hold bus bit if there are no
|
|
* further messages to be processed.
|
|
*/
|
|
done_flag = 1;
|
|
}
|
|
if (!id->send_count && !id->bus_hold_flag)
|
|
cdns_i2c_clear_bus_hold(id);
|
|
|
|
status = IRQ_HANDLED;
|
|
}
|
|
|
|
/* Update the status for errors */
|
|
id->err_status |= isr_status & CDNS_I2C_IXR_ERR_INTR_MASK;
|
|
if (id->err_status)
|
|
status = IRQ_HANDLED;
|
|
|
|
if (done_flag)
|
|
complete(&id->xfer_done);
|
|
|
|
return status;
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_isr - Interrupt handler for the I2C device
|
|
* @irq: irq number for the I2C device
|
|
* @ptr: void pointer to cdns_i2c structure
|
|
*
|
|
* This function passes the control to slave/master based on current role of
|
|
* i2c controller.
|
|
*
|
|
* Return: IRQ_HANDLED always
|
|
*/
|
|
static irqreturn_t cdns_i2c_isr(int irq, void *ptr)
|
|
{
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
struct cdns_i2c *id = ptr;
|
|
|
|
if (id->dev_mode == CDNS_I2C_MODE_SLAVE)
|
|
return cdns_i2c_slave_isr(ptr);
|
|
#endif
|
|
return cdns_i2c_master_isr(ptr);
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_mrecv - Prepare and start a master receive operation
|
|
* @id: pointer to the i2c device structure
|
|
*/
|
|
static void cdns_i2c_mrecv(struct cdns_i2c *id)
|
|
{
|
|
unsigned int ctrl_reg;
|
|
unsigned int isr_status;
|
|
unsigned long flags;
|
|
bool hold_clear = false;
|
|
bool irq_save = false;
|
|
|
|
u32 addr;
|
|
|
|
id->p_recv_buf = id->p_msg->buf;
|
|
id->recv_count = id->p_msg->len;
|
|
|
|
/* Put the controller in master receive mode and clear the FIFO */
|
|
ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
|
|
ctrl_reg |= CDNS_I2C_CR_RW | CDNS_I2C_CR_CLR_FIFO;
|
|
|
|
/*
|
|
* Receive up to I2C_SMBUS_BLOCK_MAX data bytes, plus one message length
|
|
* byte, plus one checksum byte if PEC is enabled. p_msg->len will be 2 if
|
|
* PEC is enabled, otherwise 1.
|
|
*/
|
|
if (id->p_msg->flags & I2C_M_RECV_LEN)
|
|
id->recv_count = I2C_SMBUS_BLOCK_MAX + id->p_msg->len;
|
|
|
|
id->curr_recv_count = id->recv_count;
|
|
|
|
/*
|
|
* Check for the message size against FIFO depth and set the
|
|
* 'hold bus' bit if it is greater than FIFO depth.
|
|
*/
|
|
if (id->recv_count > CDNS_I2C_FIFO_DEPTH)
|
|
ctrl_reg |= CDNS_I2C_CR_HOLD;
|
|
|
|
cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
|
|
|
|
/* Clear the interrupts in interrupt status register */
|
|
isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
|
|
cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
|
|
|
|
/*
|
|
* The no. of bytes to receive is checked against the limit of
|
|
* max transfer size. Set transfer size register with no of bytes
|
|
* receive if it is less than transfer size and transfer size if
|
|
* it is more. Enable the interrupts.
|
|
*/
|
|
if (id->recv_count > CDNS_I2C_TRANSFER_SIZE) {
|
|
cdns_i2c_writereg(CDNS_I2C_TRANSFER_SIZE,
|
|
CDNS_I2C_XFER_SIZE_OFFSET);
|
|
id->curr_recv_count = CDNS_I2C_TRANSFER_SIZE;
|
|
} else {
|
|
cdns_i2c_writereg(id->recv_count, CDNS_I2C_XFER_SIZE_OFFSET);
|
|
}
|
|
|
|
/* Determine hold_clear based on number of bytes to receive and hold flag */
|
|
if (!id->bus_hold_flag &&
|
|
((id->p_msg->flags & I2C_M_RECV_LEN) != I2C_M_RECV_LEN) &&
|
|
(id->recv_count <= CDNS_I2C_FIFO_DEPTH)) {
|
|
if (cdns_i2c_readreg(CDNS_I2C_CR_OFFSET) & CDNS_I2C_CR_HOLD) {
|
|
hold_clear = true;
|
|
if (id->quirks & CDNS_I2C_BROKEN_HOLD_BIT)
|
|
irq_save = true;
|
|
}
|
|
}
|
|
|
|
addr = id->p_msg->addr;
|
|
addr &= CDNS_I2C_ADDR_MASK;
|
|
|
|
if (hold_clear) {
|
|
ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET) & ~CDNS_I2C_CR_HOLD;
|
|
/*
|
|
* In case of Xilinx Zynq SOC, clear the HOLD bit before transfer size
|
|
* register reaches '0'. This is an IP bug which causes transfer size
|
|
* register overflow to 0xFF. To satisfy this timing requirement,
|
|
* disable the interrupts on current processor core between register
|
|
* writes to slave address register and control register.
|
|
*/
|
|
if (irq_save)
|
|
local_irq_save(flags);
|
|
|
|
cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET);
|
|
cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
|
|
/* Read it back to avoid bufferring and make sure write happens */
|
|
cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
|
|
|
|
if (irq_save)
|
|
local_irq_restore(flags);
|
|
} else {
|
|
cdns_i2c_writereg(addr, CDNS_I2C_ADDR_OFFSET);
|
|
}
|
|
|
|
cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET);
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_msend - Prepare and start a master send operation
|
|
* @id: pointer to the i2c device
|
|
*/
|
|
static void cdns_i2c_msend(struct cdns_i2c *id)
|
|
{
|
|
unsigned int avail_bytes;
|
|
unsigned int bytes_to_send;
|
|
unsigned int ctrl_reg;
|
|
unsigned int isr_status;
|
|
|
|
id->p_recv_buf = NULL;
|
|
id->p_send_buf = id->p_msg->buf;
|
|
id->send_count = id->p_msg->len;
|
|
|
|
/* Set the controller in Master transmit mode and clear the FIFO. */
|
|
ctrl_reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
|
|
ctrl_reg &= ~CDNS_I2C_CR_RW;
|
|
ctrl_reg |= CDNS_I2C_CR_CLR_FIFO;
|
|
|
|
/*
|
|
* Check for the message size against FIFO depth and set the
|
|
* 'hold bus' bit if it is greater than FIFO depth.
|
|
*/
|
|
if (id->send_count > CDNS_I2C_FIFO_DEPTH)
|
|
ctrl_reg |= CDNS_I2C_CR_HOLD;
|
|
cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
|
|
|
|
/* Clear the interrupts in interrupt status register. */
|
|
isr_status = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
|
|
cdns_i2c_writereg(isr_status, CDNS_I2C_ISR_OFFSET);
|
|
|
|
/*
|
|
* Calculate the space available in FIFO. Check the message length
|
|
* against the space available, and fill the FIFO accordingly.
|
|
* Enable the interrupts.
|
|
*/
|
|
avail_bytes = CDNS_I2C_FIFO_DEPTH -
|
|
cdns_i2c_readreg(CDNS_I2C_XFER_SIZE_OFFSET);
|
|
|
|
if (id->send_count > avail_bytes)
|
|
bytes_to_send = avail_bytes;
|
|
else
|
|
bytes_to_send = id->send_count;
|
|
|
|
while (bytes_to_send--) {
|
|
cdns_i2c_writereg((*(id->p_send_buf)++), CDNS_I2C_DATA_OFFSET);
|
|
id->send_count--;
|
|
}
|
|
|
|
/*
|
|
* Clear the bus hold flag if there is no more data
|
|
* and if it is the last message.
|
|
*/
|
|
if (!id->bus_hold_flag && !id->send_count)
|
|
cdns_i2c_clear_bus_hold(id);
|
|
/* Set the slave address in address register - triggers operation. */
|
|
cdns_i2c_writereg(id->p_msg->addr & CDNS_I2C_ADDR_MASK,
|
|
CDNS_I2C_ADDR_OFFSET);
|
|
|
|
cdns_i2c_writereg(CDNS_I2C_ENABLED_INTR_MASK, CDNS_I2C_IER_OFFSET);
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_master_reset - Reset the interface
|
|
* @adap: pointer to the i2c adapter driver instance
|
|
*
|
|
* This function cleanup the fifos, clear the hold bit and status
|
|
* and disable the interrupts.
|
|
*/
|
|
static void cdns_i2c_master_reset(struct i2c_adapter *adap)
|
|
{
|
|
struct cdns_i2c *id = adap->algo_data;
|
|
u32 regval;
|
|
|
|
/* Disable the interrupts */
|
|
cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK, CDNS_I2C_IDR_OFFSET);
|
|
/* Clear the hold bit and fifos */
|
|
regval = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
|
|
regval &= ~CDNS_I2C_CR_HOLD;
|
|
regval |= CDNS_I2C_CR_CLR_FIFO;
|
|
cdns_i2c_writereg(regval, CDNS_I2C_CR_OFFSET);
|
|
/* Update the transfercount register to zero */
|
|
cdns_i2c_writereg(0, CDNS_I2C_XFER_SIZE_OFFSET);
|
|
/* Clear the interrupt status register */
|
|
regval = cdns_i2c_readreg(CDNS_I2C_ISR_OFFSET);
|
|
cdns_i2c_writereg(regval, CDNS_I2C_ISR_OFFSET);
|
|
/* Clear the status register */
|
|
regval = cdns_i2c_readreg(CDNS_I2C_SR_OFFSET);
|
|
cdns_i2c_writereg(regval, CDNS_I2C_SR_OFFSET);
|
|
}
|
|
|
|
static int cdns_i2c_process_msg(struct cdns_i2c *id, struct i2c_msg *msg,
|
|
struct i2c_adapter *adap)
|
|
{
|
|
unsigned long time_left, msg_timeout;
|
|
u32 reg;
|
|
|
|
id->p_msg = msg;
|
|
id->err_status = 0;
|
|
reinit_completion(&id->xfer_done);
|
|
|
|
/* Check for the TEN Bit mode on each msg */
|
|
reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
|
|
if (msg->flags & I2C_M_TEN) {
|
|
if (reg & CDNS_I2C_CR_NEA)
|
|
cdns_i2c_writereg(reg & ~CDNS_I2C_CR_NEA,
|
|
CDNS_I2C_CR_OFFSET);
|
|
} else {
|
|
if (!(reg & CDNS_I2C_CR_NEA))
|
|
cdns_i2c_writereg(reg | CDNS_I2C_CR_NEA,
|
|
CDNS_I2C_CR_OFFSET);
|
|
}
|
|
|
|
/* Check for the R/W flag on each msg */
|
|
if (msg->flags & I2C_M_RD)
|
|
cdns_i2c_mrecv(id);
|
|
else
|
|
cdns_i2c_msend(id);
|
|
|
|
/* Minimal time to execute this message */
|
|
msg_timeout = msecs_to_jiffies((1000 * msg->len * BITS_PER_BYTE) / id->i2c_clk);
|
|
/* Plus some wiggle room */
|
|
msg_timeout += msecs_to_jiffies(500);
|
|
|
|
if (msg_timeout < adap->timeout)
|
|
msg_timeout = adap->timeout;
|
|
|
|
/* Wait for the signal of completion */
|
|
time_left = wait_for_completion_timeout(&id->xfer_done, msg_timeout);
|
|
if (time_left == 0) {
|
|
cdns_i2c_master_reset(adap);
|
|
dev_err(id->adap.dev.parent,
|
|
"timeout waiting on completion\n");
|
|
return -ETIMEDOUT;
|
|
}
|
|
|
|
cdns_i2c_writereg(CDNS_I2C_IXR_ALL_INTR_MASK,
|
|
CDNS_I2C_IDR_OFFSET);
|
|
|
|
/* If it is bus arbitration error, try again */
|
|
if (id->err_status & CDNS_I2C_IXR_ARB_LOST)
|
|
return -EAGAIN;
|
|
|
|
if (msg->flags & I2C_M_RECV_LEN)
|
|
msg->len += min_t(unsigned int, msg->buf[0], I2C_SMBUS_BLOCK_MAX);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_master_xfer - The main i2c transfer function
|
|
* @adap: pointer to the i2c adapter driver instance
|
|
* @msgs: pointer to the i2c message structure
|
|
* @num: the number of messages to transfer
|
|
*
|
|
* Initiates the send/recv activity based on the transfer message received.
|
|
*
|
|
* Return: number of msgs processed on success, negative error otherwise
|
|
*/
|
|
static int cdns_i2c_master_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs,
|
|
int num)
|
|
{
|
|
int ret, count;
|
|
u32 reg;
|
|
struct cdns_i2c *id = adap->algo_data;
|
|
bool hold_quirk;
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
bool change_role = false;
|
|
#endif
|
|
|
|
ret = pm_runtime_resume_and_get(id->dev);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
/* Check i2c operating mode and switch if possible */
|
|
if (id->dev_mode == CDNS_I2C_MODE_SLAVE) {
|
|
if (id->slave_state != CDNS_I2C_SLAVE_STATE_IDLE) {
|
|
ret = -EAGAIN;
|
|
goto out;
|
|
}
|
|
|
|
/* Set mode to master */
|
|
cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id);
|
|
|
|
/* Mark flag to change role once xfer is completed */
|
|
change_role = true;
|
|
}
|
|
#endif
|
|
|
|
/* Check if the bus is free */
|
|
|
|
ret = readl_relaxed_poll_timeout(id->membase + CDNS_I2C_SR_OFFSET,
|
|
reg,
|
|
!(reg & CDNS_I2C_SR_BA),
|
|
CDNS_I2C_POLL_US, CDNS_I2C_TIMEOUT_US);
|
|
if (ret) {
|
|
ret = -EAGAIN;
|
|
if (id->adap.bus_recovery_info)
|
|
i2c_recover_bus(adap);
|
|
goto out;
|
|
}
|
|
|
|
hold_quirk = !!(id->quirks & CDNS_I2C_BROKEN_HOLD_BIT);
|
|
/*
|
|
* Set the flag to one when multiple messages are to be
|
|
* processed with a repeated start.
|
|
*/
|
|
if (num > 1) {
|
|
/*
|
|
* This controller does not give completion interrupt after a
|
|
* master receive message if HOLD bit is set (repeated start),
|
|
* resulting in SW timeout. Hence, if a receive message is
|
|
* followed by any other message, an error is returned
|
|
* indicating that this sequence is not supported.
|
|
*/
|
|
for (count = 0; (count < num - 1 && hold_quirk); count++) {
|
|
if (msgs[count].flags & I2C_M_RD) {
|
|
dev_warn(adap->dev.parent,
|
|
"Can't do repeated start after a receive message\n");
|
|
ret = -EOPNOTSUPP;
|
|
goto out;
|
|
}
|
|
}
|
|
id->bus_hold_flag = 1;
|
|
reg = cdns_i2c_readreg(CDNS_I2C_CR_OFFSET);
|
|
reg |= CDNS_I2C_CR_HOLD;
|
|
cdns_i2c_writereg(reg, CDNS_I2C_CR_OFFSET);
|
|
} else {
|
|
id->bus_hold_flag = 0;
|
|
}
|
|
|
|
/* Process the msg one by one */
|
|
for (count = 0; count < num; count++, msgs++) {
|
|
if (count == (num - 1))
|
|
id->bus_hold_flag = 0;
|
|
|
|
ret = cdns_i2c_process_msg(id, msgs, adap);
|
|
if (ret)
|
|
goto out;
|
|
|
|
/* Report the other error interrupts to application */
|
|
if (id->err_status) {
|
|
cdns_i2c_master_reset(adap);
|
|
|
|
if (id->err_status & CDNS_I2C_IXR_NACK) {
|
|
ret = -ENXIO;
|
|
goto out;
|
|
}
|
|
ret = -EIO;
|
|
goto out;
|
|
}
|
|
}
|
|
|
|
ret = num;
|
|
|
|
out:
|
|
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
/* Switch i2c mode to slave */
|
|
if (change_role)
|
|
cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id);
|
|
#endif
|
|
|
|
pm_runtime_mark_last_busy(id->dev);
|
|
pm_runtime_put_autosuspend(id->dev);
|
|
return ret;
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_func - Returns the supported features of the I2C driver
|
|
* @adap: pointer to the i2c adapter structure
|
|
*
|
|
* Return: 32 bit value, each bit corresponding to a feature
|
|
*/
|
|
static u32 cdns_i2c_func(struct i2c_adapter *adap)
|
|
{
|
|
u32 func = I2C_FUNC_I2C | I2C_FUNC_10BIT_ADDR |
|
|
(I2C_FUNC_SMBUS_EMUL & ~I2C_FUNC_SMBUS_QUICK) |
|
|
I2C_FUNC_SMBUS_BLOCK_DATA;
|
|
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
func |= I2C_FUNC_SLAVE;
|
|
#endif
|
|
|
|
return func;
|
|
}
|
|
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
static int cdns_reg_slave(struct i2c_client *slave)
|
|
{
|
|
int ret;
|
|
struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c,
|
|
adap);
|
|
|
|
if (id->slave)
|
|
return -EBUSY;
|
|
|
|
if (slave->flags & I2C_CLIENT_TEN)
|
|
return -EAFNOSUPPORT;
|
|
|
|
ret = pm_runtime_resume_and_get(id->dev);
|
|
if (ret < 0)
|
|
return ret;
|
|
|
|
/* Store slave information */
|
|
id->slave = slave;
|
|
|
|
/* Enable I2C slave */
|
|
cdns_i2c_set_mode(CDNS_I2C_MODE_SLAVE, id);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static int cdns_unreg_slave(struct i2c_client *slave)
|
|
{
|
|
struct cdns_i2c *id = container_of(slave->adapter, struct cdns_i2c,
|
|
adap);
|
|
|
|
pm_runtime_put(id->dev);
|
|
|
|
/* Remove slave information */
|
|
id->slave = NULL;
|
|
|
|
/* Enable I2C master */
|
|
cdns_i2c_set_mode(CDNS_I2C_MODE_MASTER, id);
|
|
|
|
return 0;
|
|
}
|
|
#endif
|
|
|
|
static const struct i2c_algorithm cdns_i2c_algo = {
|
|
.master_xfer = cdns_i2c_master_xfer,
|
|
.functionality = cdns_i2c_func,
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
.reg_slave = cdns_reg_slave,
|
|
.unreg_slave = cdns_unreg_slave,
|
|
#endif
|
|
};
|
|
|
|
/**
|
|
* cdns_i2c_calc_divs - Calculate clock dividers
|
|
* @f: I2C clock frequency
|
|
* @input_clk: Input clock frequency
|
|
* @a: First divider (return value)
|
|
* @b: Second divider (return value)
|
|
*
|
|
* f is used as input and output variable. As input it is used as target I2C
|
|
* frequency. On function exit f holds the actually resulting I2C frequency.
|
|
*
|
|
* Return: 0 on success, negative errno otherwise.
|
|
*/
|
|
static int cdns_i2c_calc_divs(unsigned long *f, unsigned long input_clk,
|
|
unsigned int *a, unsigned int *b)
|
|
{
|
|
unsigned long fscl = *f, best_fscl = *f, actual_fscl, temp;
|
|
unsigned int div_a, div_b, calc_div_a = 0, calc_div_b = 0;
|
|
unsigned int last_error, current_error;
|
|
|
|
/* calculate (divisor_a+1) x (divisor_b+1) */
|
|
temp = input_clk / (22 * fscl);
|
|
|
|
/*
|
|
* If the calculated value is negative or 0, the fscl input is out of
|
|
* range. Return error.
|
|
*/
|
|
if (!temp || (temp > (CDNS_I2C_DIVA_MAX * CDNS_I2C_DIVB_MAX)))
|
|
return -EINVAL;
|
|
|
|
last_error = -1;
|
|
for (div_a = 0; div_a < CDNS_I2C_DIVA_MAX; div_a++) {
|
|
div_b = DIV_ROUND_UP(input_clk, 22 * fscl * (div_a + 1));
|
|
|
|
if ((div_b < 1) || (div_b > CDNS_I2C_DIVB_MAX))
|
|
continue;
|
|
div_b--;
|
|
|
|
actual_fscl = input_clk / (22 * (div_a + 1) * (div_b + 1));
|
|
|
|
if (actual_fscl > fscl)
|
|
continue;
|
|
|
|
current_error = ((actual_fscl > fscl) ? (actual_fscl - fscl) :
|
|
(fscl - actual_fscl));
|
|
|
|
if (last_error > current_error) {
|
|
calc_div_a = div_a;
|
|
calc_div_b = div_b;
|
|
best_fscl = actual_fscl;
|
|
last_error = current_error;
|
|
}
|
|
}
|
|
|
|
*a = calc_div_a;
|
|
*b = calc_div_b;
|
|
*f = best_fscl;
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_setclk - This function sets the serial clock rate for the I2C device
|
|
* @clk_in: I2C clock input frequency in Hz
|
|
* @id: Pointer to the I2C device structure
|
|
*
|
|
* The device must be idle rather than busy transferring data before setting
|
|
* these device options.
|
|
* The data rate is set by values in the control register.
|
|
* The formula for determining the correct register values is
|
|
* Fscl = Fpclk/(22 x (divisor_a+1) x (divisor_b+1))
|
|
* See the hardware data sheet for a full explanation of setting the serial
|
|
* clock rate. The clock can not be faster than the input clock divide by 22.
|
|
* The two most common clock rates are 100KHz and 400KHz.
|
|
*
|
|
* Return: 0 on success, negative error otherwise
|
|
*/
|
|
static int cdns_i2c_setclk(unsigned long clk_in, struct cdns_i2c *id)
|
|
{
|
|
unsigned int div_a, div_b;
|
|
unsigned int ctrl_reg;
|
|
int ret = 0;
|
|
unsigned long fscl = id->i2c_clk;
|
|
|
|
ret = cdns_i2c_calc_divs(&fscl, clk_in, &div_a, &div_b);
|
|
if (ret)
|
|
return ret;
|
|
|
|
ctrl_reg = id->ctrl_reg;
|
|
ctrl_reg &= ~(CDNS_I2C_CR_DIVA_MASK | CDNS_I2C_CR_DIVB_MASK);
|
|
ctrl_reg |= ((div_a << CDNS_I2C_CR_DIVA_SHIFT) |
|
|
(div_b << CDNS_I2C_CR_DIVB_SHIFT));
|
|
id->ctrl_reg = ctrl_reg;
|
|
cdns_i2c_writereg(ctrl_reg, CDNS_I2C_CR_OFFSET);
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
id->ctrl_reg_diva_divb = ctrl_reg & (CDNS_I2C_CR_DIVA_MASK |
|
|
CDNS_I2C_CR_DIVB_MASK);
|
|
#endif
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_clk_notifier_cb - Clock rate change callback
|
|
* @nb: Pointer to notifier block
|
|
* @event: Notification reason
|
|
* @data: Pointer to notification data object
|
|
*
|
|
* This function is called when the cdns_i2c input clock frequency changes.
|
|
* The callback checks whether a valid bus frequency can be generated after the
|
|
* change. If so, the change is acknowledged, otherwise the change is aborted.
|
|
* New dividers are written to the HW in the pre- or post change notification
|
|
* depending on the scaling direction.
|
|
*
|
|
* Return: NOTIFY_STOP if the rate change should be aborted, NOTIFY_OK
|
|
* to acknowledge the change, NOTIFY_DONE if the notification is
|
|
* considered irrelevant.
|
|
*/
|
|
static int cdns_i2c_clk_notifier_cb(struct notifier_block *nb, unsigned long
|
|
event, void *data)
|
|
{
|
|
struct clk_notifier_data *ndata = data;
|
|
struct cdns_i2c *id = to_cdns_i2c(nb);
|
|
|
|
if (pm_runtime_suspended(id->dev))
|
|
return NOTIFY_OK;
|
|
|
|
switch (event) {
|
|
case PRE_RATE_CHANGE:
|
|
{
|
|
unsigned long input_clk = ndata->new_rate;
|
|
unsigned long fscl = id->i2c_clk;
|
|
unsigned int div_a, div_b;
|
|
int ret;
|
|
|
|
ret = cdns_i2c_calc_divs(&fscl, input_clk, &div_a, &div_b);
|
|
if (ret) {
|
|
dev_warn(id->adap.dev.parent,
|
|
"clock rate change rejected\n");
|
|
return NOTIFY_STOP;
|
|
}
|
|
|
|
/* scale up */
|
|
if (ndata->new_rate > ndata->old_rate)
|
|
cdns_i2c_setclk(ndata->new_rate, id);
|
|
|
|
return NOTIFY_OK;
|
|
}
|
|
case POST_RATE_CHANGE:
|
|
id->input_clk = ndata->new_rate;
|
|
/* scale down */
|
|
if (ndata->new_rate < ndata->old_rate)
|
|
cdns_i2c_setclk(ndata->new_rate, id);
|
|
return NOTIFY_OK;
|
|
case ABORT_RATE_CHANGE:
|
|
/* scale up */
|
|
if (ndata->new_rate > ndata->old_rate)
|
|
cdns_i2c_setclk(ndata->old_rate, id);
|
|
return NOTIFY_OK;
|
|
default:
|
|
return NOTIFY_DONE;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_runtime_suspend - Runtime suspend method for the driver
|
|
* @dev: Address of the platform_device structure
|
|
*
|
|
* Put the driver into low power mode.
|
|
*
|
|
* Return: 0 always
|
|
*/
|
|
static int __maybe_unused cdns_i2c_runtime_suspend(struct device *dev)
|
|
{
|
|
struct cdns_i2c *xi2c = dev_get_drvdata(dev);
|
|
|
|
clk_disable(xi2c->clk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_init - Controller initialisation
|
|
* @id: Device private data structure
|
|
*
|
|
* Initialise the i2c controller.
|
|
*
|
|
*/
|
|
static void cdns_i2c_init(struct cdns_i2c *id)
|
|
{
|
|
cdns_i2c_writereg(id->ctrl_reg, CDNS_I2C_CR_OFFSET);
|
|
/*
|
|
* Cadence I2C controller has a bug wherein it generates
|
|
* invalid read transaction after HW timeout in master receiver mode.
|
|
* HW timeout is not used by this driver and the interrupt is disabled.
|
|
* But the feature itself cannot be disabled. Hence maximum value
|
|
* is written to this register to reduce the chances of error.
|
|
*/
|
|
cdns_i2c_writereg(CDNS_I2C_TIMEOUT_MAX, CDNS_I2C_TIME_OUT_OFFSET);
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_runtime_resume - Runtime resume
|
|
* @dev: Address of the platform_device structure
|
|
*
|
|
* Runtime resume callback.
|
|
*
|
|
* Return: 0 on success and error value on error
|
|
*/
|
|
static int __maybe_unused cdns_i2c_runtime_resume(struct device *dev)
|
|
{
|
|
struct cdns_i2c *xi2c = dev_get_drvdata(dev);
|
|
int ret;
|
|
|
|
ret = clk_enable(xi2c->clk);
|
|
if (ret) {
|
|
dev_err(dev, "Cannot enable clock.\n");
|
|
return ret;
|
|
}
|
|
cdns_i2c_init(xi2c);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static const struct dev_pm_ops cdns_i2c_dev_pm_ops = {
|
|
SET_RUNTIME_PM_OPS(cdns_i2c_runtime_suspend,
|
|
cdns_i2c_runtime_resume, NULL)
|
|
};
|
|
|
|
static const struct cdns_platform_data r1p10_i2c_def = {
|
|
.quirks = CDNS_I2C_BROKEN_HOLD_BIT,
|
|
};
|
|
|
|
static const struct of_device_id cdns_i2c_of_match[] = {
|
|
{ .compatible = "cdns,i2c-r1p10", .data = &r1p10_i2c_def },
|
|
{ .compatible = "cdns,i2c-r1p14",},
|
|
{ /* end of table */ }
|
|
};
|
|
MODULE_DEVICE_TABLE(of, cdns_i2c_of_match);
|
|
|
|
/**
|
|
* cdns_i2c_probe - Platform registration call
|
|
* @pdev: Handle to the platform device structure
|
|
*
|
|
* This function does all the memory allocation and registration for the i2c
|
|
* device. User can modify the address mode to 10 bit address mode using the
|
|
* ioctl call with option I2C_TENBIT.
|
|
*
|
|
* Return: 0 on success, negative error otherwise
|
|
*/
|
|
static int cdns_i2c_probe(struct platform_device *pdev)
|
|
{
|
|
struct resource *r_mem;
|
|
struct cdns_i2c *id;
|
|
int ret;
|
|
const struct of_device_id *match;
|
|
|
|
id = devm_kzalloc(&pdev->dev, sizeof(*id), GFP_KERNEL);
|
|
if (!id)
|
|
return -ENOMEM;
|
|
|
|
id->dev = &pdev->dev;
|
|
platform_set_drvdata(pdev, id);
|
|
|
|
match = of_match_node(cdns_i2c_of_match, pdev->dev.of_node);
|
|
if (match && match->data) {
|
|
const struct cdns_platform_data *data = match->data;
|
|
id->quirks = data->quirks;
|
|
}
|
|
|
|
id->rinfo.pinctrl = devm_pinctrl_get(&pdev->dev);
|
|
if (IS_ERR(id->rinfo.pinctrl)) {
|
|
int err = PTR_ERR(id->rinfo.pinctrl);
|
|
|
|
dev_info(&pdev->dev, "can't get pinctrl, bus recovery not supported\n");
|
|
if (err != -ENODEV)
|
|
return err;
|
|
} else {
|
|
id->adap.bus_recovery_info = &id->rinfo;
|
|
}
|
|
|
|
id->membase = devm_platform_get_and_ioremap_resource(pdev, 0, &r_mem);
|
|
if (IS_ERR(id->membase))
|
|
return PTR_ERR(id->membase);
|
|
|
|
ret = platform_get_irq(pdev, 0);
|
|
if (ret < 0)
|
|
return ret;
|
|
id->irq = ret;
|
|
|
|
id->adap.owner = THIS_MODULE;
|
|
id->adap.dev.of_node = pdev->dev.of_node;
|
|
id->adap.algo = &cdns_i2c_algo;
|
|
id->adap.timeout = CDNS_I2C_TIMEOUT;
|
|
id->adap.retries = 3; /* Default retry value. */
|
|
id->adap.algo_data = id;
|
|
id->adap.dev.parent = &pdev->dev;
|
|
init_completion(&id->xfer_done);
|
|
snprintf(id->adap.name, sizeof(id->adap.name),
|
|
"Cadence I2C at %08lx", (unsigned long)r_mem->start);
|
|
|
|
id->clk = devm_clk_get(&pdev->dev, NULL);
|
|
if (IS_ERR(id->clk))
|
|
return dev_err_probe(&pdev->dev, PTR_ERR(id->clk),
|
|
"input clock not found.\n");
|
|
|
|
ret = clk_prepare_enable(id->clk);
|
|
if (ret)
|
|
dev_err(&pdev->dev, "Unable to enable clock.\n");
|
|
|
|
pm_runtime_set_autosuspend_delay(id->dev, CNDS_I2C_PM_TIMEOUT);
|
|
pm_runtime_use_autosuspend(id->dev);
|
|
pm_runtime_set_active(id->dev);
|
|
pm_runtime_enable(id->dev);
|
|
|
|
id->clk_rate_change_nb.notifier_call = cdns_i2c_clk_notifier_cb;
|
|
if (clk_notifier_register(id->clk, &id->clk_rate_change_nb))
|
|
dev_warn(&pdev->dev, "Unable to register clock notifier.\n");
|
|
id->input_clk = clk_get_rate(id->clk);
|
|
|
|
ret = of_property_read_u32(pdev->dev.of_node, "clock-frequency",
|
|
&id->i2c_clk);
|
|
if (ret || (id->i2c_clk > I2C_MAX_FAST_MODE_FREQ))
|
|
id->i2c_clk = I2C_MAX_STANDARD_MODE_FREQ;
|
|
|
|
#if IS_ENABLED(CONFIG_I2C_SLAVE)
|
|
/* Set initial mode to master */
|
|
id->dev_mode = CDNS_I2C_MODE_MASTER;
|
|
id->slave_state = CDNS_I2C_SLAVE_STATE_IDLE;
|
|
#endif
|
|
id->ctrl_reg = CDNS_I2C_CR_ACK_EN | CDNS_I2C_CR_NEA | CDNS_I2C_CR_MS;
|
|
|
|
ret = cdns_i2c_setclk(id->input_clk, id);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "invalid SCL clock: %u Hz\n", id->i2c_clk);
|
|
ret = -EINVAL;
|
|
goto err_clk_dis;
|
|
}
|
|
|
|
ret = devm_request_irq(&pdev->dev, id->irq, cdns_i2c_isr, 0,
|
|
DRIVER_NAME, id);
|
|
if (ret) {
|
|
dev_err(&pdev->dev, "cannot get irq %d\n", id->irq);
|
|
goto err_clk_dis;
|
|
}
|
|
cdns_i2c_init(id);
|
|
|
|
ret = i2c_add_adapter(&id->adap);
|
|
if (ret < 0)
|
|
goto err_clk_dis;
|
|
|
|
dev_info(&pdev->dev, "%u kHz mmio %08lx irq %d\n",
|
|
id->i2c_clk / 1000, (unsigned long)r_mem->start, id->irq);
|
|
|
|
return 0;
|
|
|
|
err_clk_dis:
|
|
clk_notifier_unregister(id->clk, &id->clk_rate_change_nb);
|
|
clk_disable_unprepare(id->clk);
|
|
pm_runtime_disable(&pdev->dev);
|
|
pm_runtime_set_suspended(&pdev->dev);
|
|
return ret;
|
|
}
|
|
|
|
/**
|
|
* cdns_i2c_remove - Unregister the device after releasing the resources
|
|
* @pdev: Handle to the platform device structure
|
|
*
|
|
* This function frees all the resources allocated to the device.
|
|
*
|
|
* Return: 0 always
|
|
*/
|
|
static int cdns_i2c_remove(struct platform_device *pdev)
|
|
{
|
|
struct cdns_i2c *id = platform_get_drvdata(pdev);
|
|
|
|
pm_runtime_disable(&pdev->dev);
|
|
pm_runtime_set_suspended(&pdev->dev);
|
|
pm_runtime_dont_use_autosuspend(&pdev->dev);
|
|
|
|
i2c_del_adapter(&id->adap);
|
|
clk_notifier_unregister(id->clk, &id->clk_rate_change_nb);
|
|
clk_disable_unprepare(id->clk);
|
|
|
|
return 0;
|
|
}
|
|
|
|
static struct platform_driver cdns_i2c_drv = {
|
|
.driver = {
|
|
.name = DRIVER_NAME,
|
|
.of_match_table = cdns_i2c_of_match,
|
|
.pm = &cdns_i2c_dev_pm_ops,
|
|
},
|
|
.probe = cdns_i2c_probe,
|
|
.remove = cdns_i2c_remove,
|
|
};
|
|
|
|
module_platform_driver(cdns_i2c_drv);
|
|
|
|
MODULE_AUTHOR("Xilinx Inc.");
|
|
MODULE_DESCRIPTION("Cadence I2C bus driver");
|
|
MODULE_LICENSE("GPL");
|