120 lines
3.6 KiB
Plaintext
120 lines
3.6 KiB
Plaintext
# SPDX-License-Identifier: GPL-2.0-only
|
|
#
|
|
# Counter devices
|
|
#
|
|
|
|
menuconfig COUNTER
|
|
tristate "Counter support"
|
|
help
|
|
This enables counter device support through the Generic Counter
|
|
interface. You only need to enable this, if you also want to enable
|
|
one or more of the counter device drivers below.
|
|
|
|
if COUNTER
|
|
|
|
config 104_QUAD_8
|
|
tristate "ACCES 104-QUAD-8 driver"
|
|
depends on (PC104 && X86) || COMPILE_TEST
|
|
select ISA_BUS_API
|
|
help
|
|
Say yes here to build support for the ACCES 104-QUAD-8 quadrature
|
|
encoder counter/interface device family (104-QUAD-8, 104-QUAD-4).
|
|
|
|
A counter's respective error flag may be cleared by performing a write
|
|
operation on the respective count value attribute. Although the
|
|
104-QUAD-8 counters have a 25-bit range, only the lower 24 bits may be
|
|
set, either directly or via the counter's preset attribute.
|
|
|
|
The base port addresses for the devices may be configured via the base
|
|
array module parameter. The interrupt line numbers for the devices may
|
|
be configured via the irq array module parameter.
|
|
|
|
config INTERRUPT_CNT
|
|
tristate "Interrupt counter driver"
|
|
depends on GPIOLIB
|
|
help
|
|
Select this option to enable interrupt counter driver. Any interrupt
|
|
source can be used by this driver as the event source.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called interrupt-cnt.
|
|
|
|
config STM32_TIMER_CNT
|
|
tristate "STM32 Timer encoder counter driver"
|
|
depends on MFD_STM32_TIMERS || COMPILE_TEST
|
|
help
|
|
Select this option to enable STM32 Timer quadrature encoder
|
|
and counter driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called stm32-timer-cnt.
|
|
|
|
config STM32_LPTIMER_CNT
|
|
tristate "STM32 LP Timer encoder counter driver"
|
|
depends on MFD_STM32_LPTIMER || COMPILE_TEST
|
|
help
|
|
Select this option to enable STM32 Low-Power Timer quadrature encoder
|
|
and counter driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called stm32-lptimer-cnt.
|
|
|
|
config TI_EQEP
|
|
tristate "TI eQEP counter driver"
|
|
depends on (SOC_AM33XX || COMPILE_TEST)
|
|
select REGMAP_MMIO
|
|
help
|
|
Select this option to enable the Texas Instruments Enhanced Quadrature
|
|
Encoder Pulse (eQEP) counter driver.
|
|
|
|
To compile this driver as a module, choose M here: the module will be
|
|
called ti-eqep.
|
|
|
|
config FTM_QUADDEC
|
|
tristate "Flex Timer Module Quadrature decoder driver"
|
|
depends on HAS_IOMEM && OF
|
|
help
|
|
Select this option to enable the Flex Timer Quadrature decoder
|
|
driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called ftm-quaddec.
|
|
|
|
config MICROCHIP_TCB_CAPTURE
|
|
tristate "Microchip Timer Counter Capture driver"
|
|
depends on HAS_IOMEM && OF
|
|
select REGMAP_MMIO
|
|
help
|
|
Select this option to enable the Microchip Timer Counter Block
|
|
capture driver.
|
|
|
|
To compile this driver as a module, choose M here: the
|
|
module will be called microchip-tcb-capture.
|
|
|
|
config INTEL_QEP
|
|
tristate "Intel Quadrature Encoder Peripheral driver"
|
|
depends on PCI
|
|
help
|
|
Select this option to enable the Intel Quadrature Encoder Peripheral
|
|
driver.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called intel-qep.
|
|
|
|
config TI_ECAP_CAPTURE
|
|
tristate "TI eCAP capture driver"
|
|
depends on ARCH_OMAP2PLUS || ARCH_DAVINCI_DA8XX || ARCH_KEYSTONE || ARCH_K3 || COMPILE_TEST
|
|
depends on HAS_IOMEM
|
|
select REGMAP_MMIO
|
|
help
|
|
Select this option to enable the Texas Instruments Enhanced Capture
|
|
(eCAP) driver in input mode.
|
|
|
|
It can be used to timestamp events (falling/rising edges) detected
|
|
on ECAP input signal.
|
|
|
|
To compile this driver as a module, choose M here: the module
|
|
will be called ti-ecap-capture.
|
|
|
|
endif # COUNTER
|