330 lines
6.0 KiB
Plaintext
330 lines
6.0 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Device Tree Source for the iWave-RZG1E SODIMM carrier board
|
|
*
|
|
* Copyright (C) 2017 Renesas Electronics Corp.
|
|
*/
|
|
|
|
/*
|
|
* SSI-SGTL5000
|
|
*
|
|
* This command is required when Playback/Capture
|
|
*
|
|
* amixer set "DVC Out" 100%
|
|
* amixer set "DVC In" 100%
|
|
*
|
|
* You can use Mute
|
|
*
|
|
* amixer set "DVC Out Mute" on
|
|
* amixer set "DVC In Mute" on
|
|
*
|
|
* You can use Volume Ramp
|
|
*
|
|
* amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
|
|
* amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
|
|
* amixer set "DVC Out Ramp" on
|
|
* aplay xxx.wav &
|
|
* amixer set "DVC Out" 80% // Volume Down
|
|
* amixer set "DVC Out" 100% // Volume Up
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "r8a7745-iwg22m.dtsi"
|
|
#include <dt-bindings/pwm/pwm.h>
|
|
|
|
/ {
|
|
model = "iWave Systems RainboW-G22D-SODIMM board based on RZ/G1E";
|
|
compatible = "iwave,g22d", "iwave,g22m", "renesas,r8a7745";
|
|
|
|
aliases {
|
|
ethernet0 = &avb;
|
|
serial3 = &scif4;
|
|
serial5 = &hscif1;
|
|
};
|
|
|
|
chosen {
|
|
bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
|
|
stdout-path = "serial3:115200n8";
|
|
};
|
|
|
|
audio_clock: audio_clock {
|
|
compatible = "fixed-clock";
|
|
#clock-cells = <0>;
|
|
clock-frequency = <26000000>;
|
|
};
|
|
|
|
backlight_lcd: backlight {
|
|
compatible = "pwm-backlight";
|
|
pwms = <&tpu 3 5000000 PWM_POLARITY_INVERTED>;
|
|
brightness-levels = <0 4 8 16 32 64 128 255>;
|
|
default-brightness-level = <7>;
|
|
};
|
|
|
|
lcd_panel: lcd {
|
|
compatible = "edt,etm043080dh6gp";
|
|
power-supply = <&vccq_panel>;
|
|
backlight = <&backlight_lcd>;
|
|
|
|
port {
|
|
lcd_in: endpoint {
|
|
remote-endpoint = <&du_out_rgb0>;
|
|
};
|
|
};
|
|
};
|
|
|
|
vccq_panel: regulator-vccq-panel {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "Panel VccQ";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
gpio = <&gpio1 13 GPIO_ACTIVE_LOW>;
|
|
enable-active-high;
|
|
};
|
|
|
|
vccq_sdhi0: regulator-vccq-sdhi0 {
|
|
compatible = "regulator-gpio";
|
|
|
|
regulator-name = "SDHI0 VccQ";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
|
|
gpios-states = <1>;
|
|
states = <3300000 1>, <1800000 0>;
|
|
};
|
|
|
|
rsnd_sgtl5000: sound {
|
|
compatible = "simple-audio-card";
|
|
simple-audio-card,format = "i2s";
|
|
simple-audio-card,bitclock-master = <&sndcodec>;
|
|
simple-audio-card,frame-master = <&sndcodec>;
|
|
|
|
sndcpu: simple-audio-card,cpu {
|
|
sound-dai = <&rcar_sound>;
|
|
};
|
|
|
|
sndcodec: simple-audio-card,codec {
|
|
sound-dai = <&sgtl5000>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&avb {
|
|
pinctrl-0 = <&avb_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
phy-handle = <&phy3>;
|
|
phy-mode = "gmii";
|
|
renesas,no-ether-link;
|
|
status = "okay";
|
|
|
|
phy3: ethernet-phy@3 {
|
|
/*
|
|
* On some older versions of the platform (before R4.0) the phy address
|
|
* may be 1 or 3. The address is fixed to 3 for R4.0 onwards.
|
|
*/
|
|
compatible = "ethernet-phy-id0022.1622",
|
|
"ethernet-phy-ieee802.3-c22";
|
|
reg = <3>;
|
|
micrel,led-mode = <1>;
|
|
};
|
|
};
|
|
|
|
&can0 {
|
|
pinctrl-0 = <&can0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&du {
|
|
pinctrl-0 = <&du0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
|
|
ports {
|
|
port@0 {
|
|
endpoint {
|
|
remote-endpoint = <&lcd_in>;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&hscif1 {
|
|
pinctrl-0 = <&hscif1_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
uart-has-rtscts;
|
|
status = "okay";
|
|
};
|
|
|
|
&hsusb {
|
|
status = "okay";
|
|
pinctrl-0 = <&usb0_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&i2c5 {
|
|
pinctrl-0 = <&i2c5_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
clock-frequency = <400000>;
|
|
|
|
sgtl5000: codec@a {
|
|
compatible = "fsl,sgtl5000";
|
|
#sound-dai-cells = <0>;
|
|
reg = <0x0a>;
|
|
clocks = <&audio_clock>;
|
|
VDDA-supply = <®_3p3v>;
|
|
VDDIO-supply = <®_3p3v>;
|
|
};
|
|
|
|
stmpe811@44 {
|
|
compatible = "st,stmpe811";
|
|
reg = <0x44>;
|
|
interrupt-parent = <&gpio4>;
|
|
interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
|
|
|
|
/* 3.25 MHz ADC clock speed */
|
|
st,adc-freq = <1>;
|
|
/* ADC conversion time: 80 clocks */
|
|
st,sample-time = <4>;
|
|
/* 12-bit ADC */
|
|
st,mod-12b = <1>;
|
|
/* internal ADC reference */
|
|
st,ref-sel = <0>;
|
|
|
|
stmpe_touchscreen {
|
|
compatible = "st,stmpe-ts";
|
|
/* 8 sample average control */
|
|
st,ave-ctrl = <3>;
|
|
/* 7 length fractional part in z */
|
|
st,fraction-z = <7>;
|
|
/*
|
|
* 50 mA typical 80 mA max touchscreen drivers
|
|
* current limit value
|
|
*/
|
|
st,i-drive = <1>;
|
|
/* 1 ms panel driver settling time */
|
|
st,settling = <3>;
|
|
/* 5 ms touch detect interrupt delay */
|
|
st,touch-det-delay = <5>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&pci1 {
|
|
status = "okay";
|
|
pinctrl-0 = <&usb1_pins>;
|
|
pinctrl-names = "default";
|
|
};
|
|
|
|
&pfc {
|
|
avb_pins: avb {
|
|
groups = "avb_mdio", "avb_gmii";
|
|
function = "avb";
|
|
};
|
|
|
|
backlight_pins: backlight {
|
|
groups = "tpu_to3_c";
|
|
function = "tpu";
|
|
};
|
|
|
|
can0_pins: can0 {
|
|
groups = "can0_data";
|
|
function = "can0";
|
|
};
|
|
|
|
du0_pins: du0 {
|
|
groups = "du0_rgb666", "du0_sync", "du0_disp", "du0_clk0_out";
|
|
function = "du0";
|
|
};
|
|
|
|
hscif1_pins: hscif1 {
|
|
groups = "hscif1_data", "hscif1_ctrl";
|
|
function = "hscif1";
|
|
};
|
|
|
|
i2c5_pins: i2c5 {
|
|
groups = "i2c5_b";
|
|
function = "i2c5";
|
|
};
|
|
|
|
scif4_pins: scif4 {
|
|
groups = "scif4_data_b";
|
|
function = "scif4";
|
|
};
|
|
|
|
sdhi0_pins: sd0 {
|
|
groups = "sdhi0_data4", "sdhi0_ctrl";
|
|
function = "sdhi0";
|
|
power-source = <3300>;
|
|
};
|
|
|
|
sound_pins: sound {
|
|
groups = "ssi34_ctrl", "ssi3_data", "ssi4_data";
|
|
function = "ssi";
|
|
};
|
|
|
|
usb0_pins: usb0 {
|
|
groups = "usb0";
|
|
function = "usb0";
|
|
};
|
|
|
|
usb1_pins: usb1 {
|
|
groups = "usb1";
|
|
function = "usb1";
|
|
};
|
|
};
|
|
|
|
&rcar_sound {
|
|
pinctrl-0 = <&sound_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
/* Single DAI */
|
|
|
|
#sound-dai-cells = <0>;
|
|
|
|
rcar_sound,dai {
|
|
dai0 {
|
|
playback = <&ssi3>, <&src3>, <&dvc0>;
|
|
capture = <&ssi4>, <&src4>, <&dvc1>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&scif4 {
|
|
pinctrl-0 = <&scif4_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhi0 {
|
|
pinctrl-0 = <&sdhi0_pins>;
|
|
pinctrl-names = "default";
|
|
|
|
vmmc-supply = <®_3p3v>;
|
|
vqmmc-supply = <&vccq_sdhi0>;
|
|
cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
|
|
status = "okay";
|
|
};
|
|
|
|
&ssi4 {
|
|
shared-pin;
|
|
};
|
|
|
|
&tpu {
|
|
pinctrl-0 = <&backlight_pins>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&usbphy {
|
|
status = "okay";
|
|
};
|