1226 lines
27 KiB
Plaintext
1226 lines
27 KiB
Plaintext
// SPDX-License-Identifier: GPL-2.0
|
|
/*
|
|
* Samsung's Exynos4412 based p4note device family base DT.
|
|
* Based on exynos4412-midas.dtsi.
|
|
*
|
|
* Copyright (c) 2013 Samsung Electronics Co., Ltd.
|
|
* http://www.samsung.com
|
|
*/
|
|
|
|
/dts-v1/;
|
|
#include "exynos4412.dtsi"
|
|
#include "exynos4412-ppmu-common.dtsi"
|
|
|
|
#include <dt-bindings/clock/maxim,max77686.h>
|
|
#include <dt-bindings/gpio/gpio.h>
|
|
#include <dt-bindings/input/linux-event-codes.h>
|
|
#include <dt-bindings/interrupt-controller/irq.h>
|
|
#include <dt-bindings/power/summit,smb347-charger.h>
|
|
#include "exynos-pinctrl.h"
|
|
|
|
/ {
|
|
compatible = "samsung,p4note", "samsung,exynos4412", "samsung,exynos4";
|
|
|
|
memory@40000000 {
|
|
device_type = "memory";
|
|
reg = <0x40000000 0x80000000>;
|
|
};
|
|
|
|
chosen {
|
|
stdout-path = &serial_2;
|
|
};
|
|
|
|
firmware@204f000 {
|
|
compatible = "samsung,secure-firmware";
|
|
reg = <0x0204F000 0x1000>;
|
|
};
|
|
|
|
fixed-rate-clocks {
|
|
xxti {
|
|
compatible = "samsung,clock-xxti";
|
|
clock-frequency = <0>;
|
|
};
|
|
|
|
xusbxti {
|
|
compatible = "samsung,clock-xusbxti";
|
|
clock-frequency = <24000000>;
|
|
};
|
|
};
|
|
|
|
gpio-keys {
|
|
compatible = "gpio-keys";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&gpio_keys>;
|
|
|
|
key-down {
|
|
gpios = <&gpx2 2 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_VOLUMEDOWN>;
|
|
label = "volume down";
|
|
debounce-interval = <10>;
|
|
};
|
|
|
|
key-up {
|
|
gpios = <&gpx3 3 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_VOLUMEUP>;
|
|
label = "volume up";
|
|
debounce-interval = <10>;
|
|
};
|
|
|
|
key-power {
|
|
gpios = <&gpx2 7 GPIO_ACTIVE_LOW>;
|
|
linux,code = <KEY_POWER>;
|
|
label = "power";
|
|
debounce-interval = <10>;
|
|
wakeup-source;
|
|
};
|
|
};
|
|
|
|
voltage-regulator-1 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "TSP_LDO1";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tsp_reg_gpio_1>;
|
|
gpios = <&gpm4 5 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
};
|
|
|
|
voltage-regulator-2 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "TSP_LDO2";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tsp_reg_gpio_2>;
|
|
gpios = <&gpb 5 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
};
|
|
|
|
voltage-regulator-3 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "TSP_LDO3";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&tsp_reg_gpio_3>;
|
|
gpios = <&gpb 7 GPIO_ACTIVE_HIGH>;
|
|
startup-delay-us = <20000>;
|
|
enable-active-high;
|
|
regulator-always-on;
|
|
};
|
|
|
|
panel_vdd: voltage-regulator-4 {
|
|
compatible = "regulator-fixed";
|
|
regulator-name = "LCD_ENABLE";
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&lcd_enable>;
|
|
gpios = <&gpc0 1 GPIO_ACTIVE_HIGH>;
|
|
enable-active-high;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
wlan_pwrseq: sdhci3-pwrseq {
|
|
compatible = "mmc-pwrseq-simple";
|
|
reset-gpios = <&gpm3 5 GPIO_ACTIVE_LOW>;
|
|
pinctrl-0 = <&wifi_reset>;
|
|
pinctrl-names = "default";
|
|
clocks = <&max77686 MAX77686_CLK_PMIC>;
|
|
clock-names = "ext_clock";
|
|
};
|
|
|
|
battery_cell: battery-cell {
|
|
compatible = "simple-battery";
|
|
device-chemistry = "lithium-ion";
|
|
constant-charge-current-max-microamp = <2200000>;
|
|
precharge-current-microamp = <250000>;
|
|
charge-term-current-microamp = <250000>;
|
|
constant-charge-voltage-max-microvolt = <4200000>;
|
|
|
|
power-supplies = <&power_supply>;
|
|
};
|
|
|
|
i2c-gpio-1 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpy2 4 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpy2 5 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
magnetometer@c {
|
|
compatible = "asahi-kasei,ak8975";
|
|
reg = <0x0c>;
|
|
pinctrl-0 = <&ak8975_irq>;
|
|
pinctrl-names = "default";
|
|
interrupt-parent = <&gpm4>;
|
|
interrupts = <7 IRQ_TYPE_EDGE_RISING>;
|
|
};
|
|
};
|
|
|
|
i2c-gpio-2 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpy0 2 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpy0 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
fuel-gauge@36 {
|
|
compatible = "maxim,max17042";
|
|
reg = <0x36>;
|
|
pinctrl-0 = <&fuel_alert_irq>;
|
|
pinctrl-names = "default";
|
|
interrupt-parent = <&gpx2>;
|
|
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
|
maxim,rsns-microohm = <10000>;
|
|
maxim,over-heat-temp = <600>;
|
|
maxim,over-volt = <4300>;
|
|
};
|
|
};
|
|
|
|
i2c-gpio-3 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpm4 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpm4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
i2c-gpio,delay-us = <5>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
adc@41 {
|
|
compatible = "st,stmpe811";
|
|
reg = <0x41>;
|
|
pinctrl-0 = <&stmpe_adc_irq>;
|
|
pinctrl-names = "default";
|
|
interrupt-parent = <&gpx0>;
|
|
interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
|
|
interrupt-controller;
|
|
irq-trigger = <0x1>;
|
|
st,adc-freq = <3>;
|
|
st,mod-12b = <1>;
|
|
st,ref-sel = <0>;
|
|
st,sample-time = <3>;
|
|
|
|
stmpe_adc {
|
|
compatible = "st,stmpe-adc";
|
|
#io-channel-cells = <1>;
|
|
st,norequest-mask = <0x2F>;
|
|
};
|
|
};
|
|
};
|
|
|
|
i2c-gpio-4 {
|
|
compatible = "i2c-gpio";
|
|
sda-gpios = <&gpm2 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
scl-gpios = <&gpm2 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
|
|
|
|
i2c-gpio,delay-us = <2>;
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
|
|
power_supply: charger@6 {
|
|
compatible = "summit,smb347";
|
|
reg = <0x6>;
|
|
summit,enable-usb-charging;
|
|
summit,enable-charge-control = <SMB3XX_CHG_ENABLE_SW>;
|
|
summit,fast-voltage-threshold-microvolt = <2600000>;
|
|
summit,chip-temperature-threshold-celsius = <130>;
|
|
summit,usb-current-limit-microamp = <1800000>;
|
|
|
|
monitored-battery = <&battery_cell>;
|
|
};
|
|
};
|
|
|
|
panel {
|
|
compatible = "samsung,ltl101al01";
|
|
pinctrl-0 = <&lvds_nshdn>;
|
|
pinctrl-names = "default";
|
|
power-supply = <&panel_vdd>;
|
|
enable-gpios = <&gpm0 5 GPIO_ACTIVE_HIGH>;
|
|
backlight = <&backlight>;
|
|
|
|
port {
|
|
lcd_ep: endpoint {
|
|
remote-endpoint = <&fimd_ep>;
|
|
};
|
|
};
|
|
};
|
|
|
|
backlight: backlight {
|
|
compatible = "pwm-backlight";
|
|
pinctrl-0 = <&led_bl_reset>;
|
|
pinctrl-names = "default";
|
|
enable-gpios = <&gpm0 1 GPIO_ACTIVE_HIGH>;
|
|
pwms = <&pwm 1 78770 0>;
|
|
brightness-levels = <0 48 128 255>;
|
|
num-interpolated-steps = <8>;
|
|
default-brightness-level = <12>;
|
|
};
|
|
};
|
|
|
|
&adc {
|
|
vdd-supply = <&ldo3_reg>;
|
|
/* not verified */
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_dmc {
|
|
devfreq-events = <&ppmu_dmc0_3>, <&ppmu_dmc1_3>;
|
|
vdd-supply = <&buck1_reg>;
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_acp {
|
|
devfreq = <&bus_dmc>;
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_c2c {
|
|
devfreq = <&bus_dmc>;
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_leftbus {
|
|
devfreq-events = <&ppmu_leftbus_3>, <&ppmu_rightbus_3>;
|
|
vdd-supply = <&buck3_reg>;
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_rightbus {
|
|
devfreq = <&bus_leftbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_display {
|
|
devfreq = <&bus_leftbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_fsys {
|
|
devfreq = <&bus_leftbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_peri {
|
|
devfreq = <&bus_leftbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&bus_mfc {
|
|
devfreq = <&bus_leftbus>;
|
|
status = "okay";
|
|
};
|
|
|
|
&cpu0 {
|
|
cpu0-supply = <&buck2_reg>;
|
|
};
|
|
|
|
&cpu_thermal {
|
|
cooling-maps {
|
|
map0 {
|
|
/* Corresponds to 800MHz at freq_table */
|
|
cooling-device = <&cpu0 7 7>, <&cpu1 7 7>,
|
|
<&cpu2 7 7>, <&cpu3 7 7>;
|
|
};
|
|
map1 {
|
|
/* Corresponds to 200MHz at freq_table */
|
|
cooling-device = <&cpu0 13 13>, <&cpu1 13 13>,
|
|
<&cpu2 13 13>, <&cpu3 13 13>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&exynos_usbphy {
|
|
status = "okay";
|
|
};
|
|
|
|
&fimd {
|
|
pinctrl-0 = <&lcd_clk &lcd_data24>;
|
|
pinctrl-names = "default";
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
status = "okay";
|
|
|
|
samsung,invert-vclk;
|
|
|
|
port@3 {
|
|
reg = <3>;
|
|
|
|
fimd_ep: endpoint {
|
|
remote-endpoint = <&lcd_ep>;
|
|
};
|
|
};
|
|
};
|
|
|
|
&gpu {
|
|
mali-supply = <&buck4_reg>;
|
|
status = "okay";
|
|
};
|
|
|
|
&hsotg {
|
|
vusb_a-supply = <&ldo12_reg>;
|
|
dr_mode = "peripheral";
|
|
status = "okay";
|
|
};
|
|
|
|
&i2c_3 {
|
|
samsung,i2c-sda-delay = <100>;
|
|
samsung,i2c-slave-addr = <0x10>;
|
|
samsung,i2c-max-bus-freq = <400000>;
|
|
pinctrl-0 = <&i2c3_bus>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
touchscreen@4a {
|
|
compatible = "atmel,maxtouch";
|
|
reg = <0x4a>;
|
|
pinctrl-0 = <&tsp_rst &tsp_irq>;
|
|
pinctrl-names = "default";
|
|
interrupt-parent = <&gpm2>;
|
|
interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
|
|
reset-gpios = <&gpm0 4 GPIO_ACTIVE_LOW>;
|
|
};
|
|
};
|
|
|
|
&i2c_7 {
|
|
samsung,i2c-sda-delay = <100>;
|
|
samsung,i2c-slave-addr = <0x10>;
|
|
samsung,i2c-max-bus-freq = <400000>;
|
|
pinctrl-0 = <&i2c7_bus>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
max77686: pmic@9 {
|
|
compatible = "maxim,max77686";
|
|
interrupt-parent = <&gpx0>;
|
|
interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
|
|
pinctrl-0 = <&max77686_irq>;
|
|
pinctrl-names = "default";
|
|
wakeup-source;
|
|
reg = <0x09>;
|
|
#clock-cells = <1>;
|
|
|
|
voltage-regulators {
|
|
ldo1_reg: LDO1 {
|
|
regulator-name = "ldo1";
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo2_reg: LDO2 {
|
|
regulator-name = "ldo2";
|
|
regulator-always-on;
|
|
};
|
|
|
|
/* WM8994 audio */
|
|
ldo3_reg: LDO3 {
|
|
regulator-name = "VCC_1.8V_AP";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-on-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo4_reg: LDO4 {
|
|
regulator-name = "ldo4";
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo5_reg: LDO5 {
|
|
regulator-name = "VCC_1.8V_IO";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo6_reg: LDO6 {
|
|
regulator-name = "ldo6";
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo7_reg: LDO7 {
|
|
regulator-name = "ldo7";
|
|
regulator-always-on;
|
|
};
|
|
|
|
/* CSI IP block */
|
|
ldo8_reg: LDO8 {
|
|
regulator-name = "VMIPI_1.0V";
|
|
regulator-min-microvolt = <1000000>;
|
|
regulator-max-microvolt = <1000000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-on-in-suspend;
|
|
};
|
|
};
|
|
|
|
/* IR LED on/off */
|
|
ldo9_reg: LDO9 {
|
|
regulator-name = "VLED_IC_1.9V";
|
|
regulator-min-microvolt = <1950000>;
|
|
regulator-max-microvolt = <1950000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
/* CSI IP block */
|
|
ldo10_reg: LDO10 {
|
|
regulator-name = "VMIPI_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-on-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo11_reg: LDO11 {
|
|
regulator-name = "VABB1_1.9V";
|
|
regulator-min-microvolt = <1950000>;
|
|
regulator-max-microvolt = <1950000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
/* USB OTG */
|
|
ldo12_reg: LDO12 {
|
|
regulator-name = "VUOTG_3.0V";
|
|
regulator-min-microvolt = <3000000>;
|
|
regulator-max-microvolt = <3000000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-on-in-suspend;
|
|
};
|
|
};
|
|
|
|
/* not connected */
|
|
ldo13_reg: LDO13 {
|
|
regulator-name = "ldo13";
|
|
};
|
|
|
|
ldo14_reg: LDO14 {
|
|
regulator-name = "VABB2_1.9V";
|
|
regulator-min-microvolt = <1950000>;
|
|
regulator-max-microvolt = <1950000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo15_reg: LDO15 {
|
|
regulator-name = "ldo15";
|
|
regulator-always-on;
|
|
};
|
|
|
|
ldo16_reg: LDO16 {
|
|
regulator-name = "ldo16";
|
|
regulator-always-on;
|
|
};
|
|
|
|
/* not connected */
|
|
ldo17_reg: LDO17 {
|
|
regulator-name = "ldo17";
|
|
};
|
|
|
|
/* Camera ISX012 */
|
|
ldo18_reg: LDO18 {
|
|
regulator-name = "CAM_IO_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
/* Camera S5K6A3 */
|
|
ldo19_reg: LDO19 {
|
|
regulator-name = "VT_CORE_1.8V";
|
|
regulator-min-microvolt = <1800000>;
|
|
regulator-max-microvolt = <1800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
/* not connected */
|
|
ldo20_reg: LDO20 {
|
|
regulator-name = "ldo20";
|
|
};
|
|
|
|
/* MMC2 */
|
|
ldo21_reg: LDO21 {
|
|
regulator-name = "VTF_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
maxim,ena-gpios = <&gpy2 0 GPIO_ACTIVE_HIGH>;
|
|
};
|
|
|
|
/* not connected */
|
|
ldo22_reg: LDO22 {
|
|
regulator-name = "ldo22";
|
|
};
|
|
|
|
/* ADC */
|
|
ldo23_reg: LDO23 {
|
|
regulator-name = "VDD_ADC_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
/* Camera S5K6A3 */
|
|
ldo24_reg: LDO24 {
|
|
regulator-name = "CAM_A2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
ldo25_reg: LDO25 {
|
|
regulator-name = "VLED_3.3V";
|
|
regulator-min-microvolt = <3300000>;
|
|
regulator-max-microvolt = <3300000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
/* Camera ISX012 */
|
|
ldo26_reg: LDO26 {
|
|
regulator-name = "3MP_AF_2.8V";
|
|
regulator-min-microvolt = <2800000>;
|
|
regulator-max-microvolt = <2800000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
|
|
buck1_reg: BUCK1 {
|
|
regulator-name = "VDD_MIF";
|
|
regulator-min-microvolt = <850000>;
|
|
regulator-max-microvolt = <1050000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
buck2_reg: BUCK2 {
|
|
regulator-name = "VDD_ARM";
|
|
regulator-min-microvolt = <850000>;
|
|
regulator-max-microvolt = <1500000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
buck3_reg: BUCK3 {
|
|
regulator-name = "VDD_INT";
|
|
regulator-min-microvolt = <850000>;
|
|
regulator-max-microvolt = <1100000>;
|
|
regulator-always-on;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
buck4_reg: BUCK4 {
|
|
regulator-name = "VDD_G3D";
|
|
regulator-min-microvolt = <850000>;
|
|
regulator-max-microvolt = <1075000>;
|
|
regulator-boot-on;
|
|
};
|
|
|
|
buck5_reg: BUCK5 {
|
|
regulator-name = "buck5";
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck6_reg: BUCK6 {
|
|
regulator-name = "buck6";
|
|
regulator-always-on;
|
|
};
|
|
|
|
buck7_reg: BUCK7 {
|
|
regulator-name = "buck7";
|
|
regulator-always-on;
|
|
};
|
|
|
|
/* not connected */
|
|
buck8_reg: BUCK8 {
|
|
regulator-name = "buck8";
|
|
};
|
|
|
|
buck9_reg: BUCK9 {
|
|
regulator-name = "3MP_CORE_1.2V";
|
|
regulator-min-microvolt = <1200000>;
|
|
regulator-max-microvolt = <1200000>;
|
|
|
|
regulator-state-mem {
|
|
regulator-off-in-suspend;
|
|
};
|
|
};
|
|
};
|
|
};
|
|
};
|
|
|
|
&mshc_0 {
|
|
broken-cd;
|
|
non-removable;
|
|
card-detect-delay = <200>;
|
|
clock-frequency = <400000000>;
|
|
samsung,dw-mshc-ciu-div = <0>;
|
|
samsung,dw-mshc-sdr-timing = <2 3>;
|
|
samsung,dw-mshc-ddr-timing = <1 2>;
|
|
pinctrl-0 = <&sd4_clk &sd4_cmd &sd4_bus4 &sd4_bus8>;
|
|
pinctrl-names = "default";
|
|
bus-width = <4>;
|
|
cap-mmc-highspeed;
|
|
cap-sd-highspeed;
|
|
status = "okay";
|
|
};
|
|
|
|
&pinctrl_0 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sleep0>;
|
|
|
|
tsp_reg_gpio_2: tsp-reg-gpio-2-pins {
|
|
samsung,pins = "gpb-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
tsp_reg_gpio_3: tsp-reg-gpio-3-pins {
|
|
samsung,pins = "gpb-7";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
lcd_enable: lcd-enable-pins {
|
|
samsung,pins = "gpc0-1";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
sleep0: sleep-state {
|
|
PIN_SLP(gpa0-0, INPUT, NONE);
|
|
PIN_SLP(gpa0-1, OUT0, NONE);
|
|
PIN_SLP(gpa0-2, INPUT, NONE);
|
|
PIN_SLP(gpa0-3, INPUT, UP);
|
|
PIN_SLP(gpa0-4, INPUT, NONE);
|
|
PIN_SLP(gpa0-5, INPUT, DOWN);
|
|
PIN_SLP(gpa0-6, INPUT, DOWN);
|
|
PIN_SLP(gpa0-7, INPUT, UP);
|
|
|
|
PIN_SLP(gpa1-0, INPUT, DOWN);
|
|
PIN_SLP(gpa1-1, INPUT, DOWN);
|
|
PIN_SLP(gpa1-2, INPUT, DOWN);
|
|
PIN_SLP(gpa1-3, INPUT, DOWN);
|
|
PIN_SLP(gpa1-4, INPUT, DOWN);
|
|
PIN_SLP(gpa1-5, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpb-0, INPUT, NONE);
|
|
PIN_SLP(gpb-1, INPUT, NONE);
|
|
PIN_SLP(gpb-2, INPUT, NONE);
|
|
PIN_SLP(gpb-3, INPUT, NONE);
|
|
PIN_SLP(gpb-4, INPUT, DOWN);
|
|
PIN_SLP(gpb-5, INPUT, DOWN);
|
|
PIN_SLP(gpb-6, INPUT, DOWN);
|
|
PIN_SLP(gpb-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpc0-0, INPUT, DOWN);
|
|
PIN_SLP(gpc0-1, INPUT, DOWN);
|
|
PIN_SLP(gpc0-2, INPUT, DOWN);
|
|
PIN_SLP(gpc0-3, INPUT, DOWN);
|
|
PIN_SLP(gpc0-4, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpc1-0, INPUT, UP);
|
|
PIN_SLP(gpc1-1, PREV, NONE);
|
|
PIN_SLP(gpc1-2, INPUT, UP);
|
|
PIN_SLP(gpc1-3, INPUT, UP);
|
|
PIN_SLP(gpc1-4, INPUT, UP);
|
|
|
|
PIN_SLP(gpd0-0, INPUT, DOWN);
|
|
PIN_SLP(gpd0-1, OUT0, NONE);
|
|
PIN_SLP(gpd0-2, INPUT, NONE);
|
|
PIN_SLP(gpd0-3, INPUT, NONE);
|
|
|
|
PIN_SLP(gpd1-0, INPUT, DOWN);
|
|
PIN_SLP(gpd1-1, INPUT, DOWN);
|
|
PIN_SLP(gpd1-2, INPUT, NONE);
|
|
PIN_SLP(gpd1-3, INPUT, NONE);
|
|
|
|
PIN_SLP(gpf0-0, OUT0, NONE);
|
|
PIN_SLP(gpf0-1, OUT0, NONE);
|
|
PIN_SLP(gpf0-2, OUT0, NONE);
|
|
PIN_SLP(gpf0-3, OUT0, NONE);
|
|
PIN_SLP(gpf0-4, OUT0, NONE);
|
|
PIN_SLP(gpf0-5, OUT0, NONE);
|
|
PIN_SLP(gpf0-6, OUT0, NONE);
|
|
PIN_SLP(gpf0-7, OUT0, NONE);
|
|
|
|
PIN_SLP(gpf1-0, OUT0, NONE);
|
|
PIN_SLP(gpf1-1, OUT0, NONE);
|
|
PIN_SLP(gpf1-2, OUT0, NONE);
|
|
PIN_SLP(gpf1-3, OUT0, NONE);
|
|
PIN_SLP(gpf1-4, OUT0, NONE);
|
|
PIN_SLP(gpf1-5, OUT0, NONE);
|
|
PIN_SLP(gpf1-6, OUT0, NONE);
|
|
PIN_SLP(gpf1-7, OUT0, NONE);
|
|
|
|
PIN_SLP(gpf2-0, OUT0, NONE);
|
|
PIN_SLP(gpf2-1, OUT0, NONE);
|
|
PIN_SLP(gpf2-2, OUT0, NONE);
|
|
PIN_SLP(gpf2-3, OUT0, NONE);
|
|
PIN_SLP(gpf2-4, OUT0, NONE);
|
|
PIN_SLP(gpf2-5, OUT0, NONE);
|
|
PIN_SLP(gpf2-6, OUT0, NONE);
|
|
PIN_SLP(gpf2-7, OUT0, NONE);
|
|
|
|
PIN_SLP(gpf3-0, OUT0, NONE);
|
|
PIN_SLP(gpf3-1, OUT0, NONE);
|
|
PIN_SLP(gpf3-2, OUT0, NONE);
|
|
PIN_SLP(gpf3-3, OUT0, NONE);
|
|
PIN_SLP(gpf3-4, OUT0, NONE);
|
|
PIN_SLP(gpf3-5, OUT0, NONE);
|
|
|
|
PIN_SLP(gpj0-0, INPUT, DOWN);
|
|
PIN_SLP(gpj0-1, INPUT, DOWN);
|
|
PIN_SLP(gpj0-2, INPUT, DOWN);
|
|
PIN_SLP(gpj0-3, PREV, NONE);
|
|
PIN_SLP(gpj0-4, PREV, NONE);
|
|
PIN_SLP(gpj0-5, OUT0, NONE);
|
|
PIN_SLP(gpj0-6, OUT0, NONE);
|
|
PIN_SLP(gpj0-7, OUT0, NONE);
|
|
|
|
PIN_SLP(gpj1-0, OUT0, NONE);
|
|
PIN_SLP(gpj1-1, INPUT, DOWN);
|
|
PIN_SLP(gpj1-2, PREV, NONE);
|
|
PIN_SLP(gpj1-3, OUT0, NONE);
|
|
};
|
|
};
|
|
|
|
&pinctrl_1 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sleep1>;
|
|
|
|
sd3_wifi: sd3-wifi-pins {
|
|
samsung,pins = "gpk3-3", "gpk3-4", "gpk3-5", "gpk3-6";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_2>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
bt_shutdown: bt-shutdown-pins {
|
|
samsung,pins = "gpl0-6";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
uart_sel: uart-sel-pins {
|
|
samsung,pins = "gpl2-7";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
samsung,pin-val = <1>;
|
|
/* 0 = CP, 1 = AP (serial output) */
|
|
};
|
|
|
|
led_bl_reset: led-bl-reset-pins {
|
|
samsung,pins = "gpm0-1";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
tsp_rst: tsp-rst-pins {
|
|
samsung,pins = "gpm0-4";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
lvds_nshdn: lvds-nshdn-pins {
|
|
samsung,pins = "gpm0-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
tsp_irq: tsp-irq-pins {
|
|
samsung,pins = "gpm2-3";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
wifi_reset: wifi-reset-pins {
|
|
samsung,pins = "gpm3-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
tsp_reg_gpio_1: tsp-reg-gpio-1-pins {
|
|
samsung,pins = "gpm4-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
ak8975_irq: ak8975-irq-pins {
|
|
samsung,pins = "gpm4-7";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
|
|
};
|
|
|
|
stmpe_adc_irq: stmpe-adc-irq-pins {
|
|
samsung,pins = "gpx0-1";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
max77686_irq: max77686-irq-pins {
|
|
samsung,pins = "gpx0-7";
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
gpio_keys: gpio-keys-pins {
|
|
samsung,pins = "gpx2-2", "gpx2-7", "gpx3-3";
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
fuel_alert_irq: fuel-alert-irq-pins {
|
|
samsung,pins = "gpx2-3";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
wifi_host_wake: wifi-host-wake-pins {
|
|
samsung,pins = "gpx2-5";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_F>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_DOWN>;
|
|
};
|
|
|
|
bt_host_wakeup: bt-host-wakeup-pins {
|
|
samsung,pins = "gpx2-6";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
bt_device_wakeup: bt-device-wakeup-pins {
|
|
samsung,pins = "gpx3-1";
|
|
samsung,pin-function = <EXYNOS_PIN_FUNC_OUTPUT>;
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
sdhci2_cd: sdhci2-cd-pins {
|
|
samsung,pins = "gpx3-4";
|
|
samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
|
|
};
|
|
|
|
sleep1: sleep-state {
|
|
PIN_SLP(gpk0-0, PREV, NONE);
|
|
PIN_SLP(gpk0-1, PREV, NONE);
|
|
PIN_SLP(gpk0-2, PREV, NONE);
|
|
PIN_SLP(gpk0-3, PREV, NONE);
|
|
PIN_SLP(gpk0-4, PREV, NONE);
|
|
PIN_SLP(gpk0-5, PREV, NONE);
|
|
PIN_SLP(gpk0-6, PREV, NONE);
|
|
|
|
PIN_SLP(gpk1-0, INPUT, DOWN);
|
|
PIN_SLP(gpk1-1, INPUT, DOWN);
|
|
PIN_SLP(gpk1-2, INPUT, DOWN);
|
|
PIN_SLP(gpk1-3, PREV, NONE);
|
|
PIN_SLP(gpk1-4, PREV, NONE);
|
|
PIN_SLP(gpk1-5, PREV, NONE);
|
|
PIN_SLP(gpk1-6, PREV, NONE);
|
|
|
|
PIN_SLP(gpk2-0, INPUT, DOWN);
|
|
PIN_SLP(gpk2-1, INPUT, DOWN);
|
|
PIN_SLP(gpk2-2, INPUT, DOWN);
|
|
PIN_SLP(gpk2-3, INPUT, DOWN);
|
|
PIN_SLP(gpk2-4, INPUT, DOWN);
|
|
PIN_SLP(gpk2-5, INPUT, DOWN);
|
|
PIN_SLP(gpk2-6, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpk3-0, OUT0, NONE);
|
|
PIN_SLP(gpk3-1, INPUT, NONE);
|
|
PIN_SLP(gpk3-2, INPUT, DOWN);
|
|
PIN_SLP(gpk3-3, INPUT, NONE);
|
|
PIN_SLP(gpk3-4, INPUT, NONE);
|
|
PIN_SLP(gpk3-5, INPUT, NONE);
|
|
PIN_SLP(gpk3-6, INPUT, NONE);
|
|
|
|
PIN_SLP(gpl0-0, OUT0, NONE);
|
|
PIN_SLP(gpl0-1, INPUT, NONE);
|
|
PIN_SLP(gpl0-2, INPUT, NONE);
|
|
PIN_SLP(gpl0-3, INPUT, DOWN);
|
|
PIN_SLP(gpl0-4, PREV, NONE);
|
|
PIN_SLP(gpl0-6, PREV, NONE);
|
|
|
|
PIN_SLP(gpl1-0, OUT0, NONE);
|
|
PIN_SLP(gpl1-1, OUT0, NONE);
|
|
|
|
PIN_SLP(gpl2-0, INPUT, DOWN);
|
|
PIN_SLP(gpl2-1, INPUT, DOWN);
|
|
PIN_SLP(gpl2-2, INPUT, DOWN);
|
|
PIN_SLP(gpl2-3, INPUT, DOWN);
|
|
PIN_SLP(gpl2-4, OUT0, NONE);
|
|
PIN_SLP(gpl2-5, INPUT, DOWN);
|
|
PIN_SLP(gpl2-6, PREV, NONE);
|
|
PIN_SLP(gpl2-7, PREV, NONE);
|
|
|
|
PIN_SLP(gpm0-0, PREV, NONE);
|
|
PIN_SLP(gpm0-1, OUT0, NONE);
|
|
PIN_SLP(gpm0-2, INPUT, DOWN);
|
|
PIN_SLP(gpm0-3, INPUT, NONE);
|
|
PIN_SLP(gpm0-4, OUT0, NONE);
|
|
PIN_SLP(gpm0-5, OUT0, NONE);
|
|
PIN_SLP(gpm0-6, INPUT, DOWN);
|
|
PIN_SLP(gpm0-7, OUT0, NONE);
|
|
|
|
PIN_SLP(gpm1-0, INPUT, NONE);
|
|
PIN_SLP(gpm1-1, INPUT, NONE);
|
|
PIN_SLP(gpm1-2, INPUT, NONE);
|
|
PIN_SLP(gpm1-3, INPUT, NONE);
|
|
PIN_SLP(gpm1-4, INPUT, NONE);
|
|
PIN_SLP(gpm1-5, INPUT, NONE);
|
|
PIN_SLP(gpm1-6, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpm2-0, INPUT, NONE);
|
|
PIN_SLP(gpm2-1, INPUT, NONE);
|
|
PIN_SLP(gpm2-2, OUT0, NONE);
|
|
PIN_SLP(gpm2-3, OUT0, DOWN);
|
|
PIN_SLP(gpm2-4, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpm3-0, PREV, NONE);
|
|
PIN_SLP(gpm3-1, PREV, NONE);
|
|
PIN_SLP(gpm3-2, PREV, NONE);
|
|
PIN_SLP(gpm3-3, OUT1, NONE);
|
|
PIN_SLP(gpm3-4, OUT0, DOWN);
|
|
PIN_SLP(gpm3-5, PREV, NONE);
|
|
PIN_SLP(gpm3-6, PREV, NONE);
|
|
PIN_SLP(gpm3-7, OUT0, NONE);
|
|
|
|
PIN_SLP(gpm4-0, INPUT, NONE);
|
|
PIN_SLP(gpm4-1, INPUT, NONE);
|
|
PIN_SLP(gpm4-2, INPUT, DOWN);
|
|
PIN_SLP(gpm4-3, INPUT, DOWN);
|
|
PIN_SLP(gpm4-4, PREV, NONE);
|
|
PIN_SLP(gpm4-5, OUT0, NONE);
|
|
PIN_SLP(gpm4-6, OUT0, NONE);
|
|
PIN_SLP(gpm4-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpy0-0, INPUT, DOWN);
|
|
PIN_SLP(gpy0-1, INPUT, DOWN);
|
|
PIN_SLP(gpy0-2, INPUT, NONE);
|
|
PIN_SLP(gpy0-3, INPUT, NONE);
|
|
PIN_SLP(gpy0-4, INPUT, NONE);
|
|
PIN_SLP(gpy0-5, INPUT, NONE);
|
|
|
|
PIN_SLP(gpy1-0, INPUT, DOWN);
|
|
PIN_SLP(gpy1-1, INPUT, DOWN);
|
|
PIN_SLP(gpy1-2, INPUT, DOWN);
|
|
PIN_SLP(gpy1-3, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpy2-0, PREV, NONE);
|
|
PIN_SLP(gpy2-1, INPUT, DOWN);
|
|
PIN_SLP(gpy2-2, INPUT, NONE);
|
|
PIN_SLP(gpy2-3, INPUT, NONE);
|
|
PIN_SLP(gpy2-4, INPUT, NONE);
|
|
PIN_SLP(gpy2-5, INPUT, NONE);
|
|
|
|
PIN_SLP(gpy3-0, INPUT, DOWN);
|
|
PIN_SLP(gpy3-1, INPUT, DOWN);
|
|
PIN_SLP(gpy3-2, INPUT, DOWN);
|
|
PIN_SLP(gpy3-3, INPUT, DOWN);
|
|
PIN_SLP(gpy3-4, INPUT, DOWN);
|
|
PIN_SLP(gpy3-5, INPUT, DOWN);
|
|
PIN_SLP(gpy3-6, INPUT, DOWN);
|
|
PIN_SLP(gpy3-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpy4-0, INPUT, DOWN);
|
|
PIN_SLP(gpy4-1, INPUT, DOWN);
|
|
PIN_SLP(gpy4-2, INPUT, DOWN);
|
|
PIN_SLP(gpy4-3, INPUT, DOWN);
|
|
PIN_SLP(gpy4-4, INPUT, DOWN);
|
|
PIN_SLP(gpy4-5, INPUT, DOWN);
|
|
PIN_SLP(gpy4-6, INPUT, DOWN);
|
|
PIN_SLP(gpy4-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpy5-0, INPUT, DOWN);
|
|
PIN_SLP(gpy5-1, INPUT, DOWN);
|
|
PIN_SLP(gpy5-2, INPUT, DOWN);
|
|
PIN_SLP(gpy5-3, INPUT, DOWN);
|
|
PIN_SLP(gpy5-4, INPUT, DOWN);
|
|
PIN_SLP(gpy5-5, INPUT, DOWN);
|
|
PIN_SLP(gpy5-6, INPUT, DOWN);
|
|
PIN_SLP(gpy5-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpy6-0, INPUT, DOWN);
|
|
PIN_SLP(gpy6-1, INPUT, DOWN);
|
|
PIN_SLP(gpy6-2, INPUT, DOWN);
|
|
PIN_SLP(gpy6-3, INPUT, DOWN);
|
|
PIN_SLP(gpy6-4, INPUT, DOWN);
|
|
PIN_SLP(gpy6-5, INPUT, DOWN);
|
|
PIN_SLP(gpy6-6, INPUT, DOWN);
|
|
PIN_SLP(gpy6-7, INPUT, DOWN);
|
|
};
|
|
};
|
|
|
|
&pinctrl_2 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sleep2>;
|
|
|
|
sleep2: sleep-state {
|
|
PIN_SLP(gpz-0, INPUT, DOWN);
|
|
PIN_SLP(gpz-1, INPUT, DOWN);
|
|
PIN_SLP(gpz-2, INPUT, DOWN);
|
|
PIN_SLP(gpz-3, INPUT, DOWN);
|
|
PIN_SLP(gpz-4, INPUT, DOWN);
|
|
PIN_SLP(gpz-5, INPUT, DOWN);
|
|
PIN_SLP(gpz-6, INPUT, DOWN);
|
|
};
|
|
};
|
|
|
|
&pinctrl_3 {
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sleep3>;
|
|
|
|
sleep3: sleep-state {
|
|
PIN_SLP(gpv0-0, INPUT, DOWN);
|
|
PIN_SLP(gpv0-1, INPUT, DOWN);
|
|
PIN_SLP(gpv0-2, INPUT, DOWN);
|
|
PIN_SLP(gpv0-3, INPUT, DOWN);
|
|
PIN_SLP(gpv0-4, INPUT, DOWN);
|
|
PIN_SLP(gpv0-5, INPUT, DOWN);
|
|
PIN_SLP(gpv0-6, INPUT, DOWN);
|
|
PIN_SLP(gpv0-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpv1-0, INPUT, DOWN);
|
|
PIN_SLP(gpv1-1, INPUT, DOWN);
|
|
PIN_SLP(gpv1-2, INPUT, DOWN);
|
|
PIN_SLP(gpv1-3, INPUT, DOWN);
|
|
PIN_SLP(gpv1-4, INPUT, DOWN);
|
|
PIN_SLP(gpv1-5, INPUT, DOWN);
|
|
PIN_SLP(gpv1-6, INPUT, DOWN);
|
|
PIN_SLP(gpv1-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpv2-0, INPUT, DOWN);
|
|
PIN_SLP(gpv2-1, INPUT, DOWN);
|
|
PIN_SLP(gpv2-2, INPUT, DOWN);
|
|
PIN_SLP(gpv2-3, INPUT, DOWN);
|
|
PIN_SLP(gpv2-4, INPUT, DOWN);
|
|
PIN_SLP(gpv2-5, INPUT, DOWN);
|
|
PIN_SLP(gpv2-6, INPUT, DOWN);
|
|
PIN_SLP(gpv2-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpv3-0, INPUT, DOWN);
|
|
PIN_SLP(gpv3-1, INPUT, DOWN);
|
|
PIN_SLP(gpv3-2, INPUT, DOWN);
|
|
PIN_SLP(gpv3-3, INPUT, DOWN);
|
|
PIN_SLP(gpv3-4, INPUT, DOWN);
|
|
PIN_SLP(gpv3-5, INPUT, DOWN);
|
|
PIN_SLP(gpv3-6, INPUT, DOWN);
|
|
PIN_SLP(gpv3-7, INPUT, DOWN);
|
|
|
|
PIN_SLP(gpv4-0, INPUT, DOWN);
|
|
PIN_SLP(gpv4-1, INPUT, DOWN);
|
|
};
|
|
};
|
|
|
|
&pmu_system_controller {
|
|
assigned-clocks = <&pmu_system_controller 0>;
|
|
assigned-clock-parents = <&clock CLK_XUSBXTI>;
|
|
};
|
|
|
|
&pwm {
|
|
pinctrl-0 = <&pwm1_out>;
|
|
pinctrl-names = "default";
|
|
samsung,pwm-outputs = <1>;
|
|
status = "okay";
|
|
};
|
|
|
|
&rtc {
|
|
clocks = <&clock CLK_RTC>, <&max77686 MAX77686_CLK_AP>;
|
|
clock-names = "rtc", "rtc_src";
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhci_2 {
|
|
bus-width = <4>;
|
|
cd-gpios = <&gpx3 4 GPIO_ACTIVE_LOW>;
|
|
pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_bus4 &sdhci2_cd>;
|
|
pinctrl-names = "default";
|
|
vmmc-supply = <&ldo21_reg>;
|
|
status = "okay";
|
|
};
|
|
|
|
&sdhci_3 {
|
|
#address-cells = <1>;
|
|
#size-cells = <0>;
|
|
non-removable;
|
|
bus-width = <4>;
|
|
mmc-pwrseq = <&wlan_pwrseq>;
|
|
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&sd3_clk &sd3_cmd &sd3_wifi>;
|
|
status = "okay";
|
|
|
|
wifi@1 {
|
|
compatible = "brcm,bcm4329-fmac";
|
|
reg = <0x1>;
|
|
pinctrl-names = "default";
|
|
pinctrl-0 = <&wifi_host_wake>;
|
|
interrupt-parent = <&gpx2>;
|
|
interrupts = <5 IRQ_TYPE_LEVEL_HIGH>;
|
|
interrupt-names = "host-wake";
|
|
};
|
|
};
|
|
|
|
&serial_0 {
|
|
pinctrl-0 = <&uart0_data &uart0_fctl>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
|
|
bluetooth {
|
|
compatible = "brcm,bcm4330-bt";
|
|
pinctrl-0 = <&bt_shutdown &bt_device_wakeup &bt_host_wakeup>;
|
|
pinctrl-names = "default";
|
|
|
|
max-speed = <2000000>;
|
|
shutdown-gpios = <&gpl0 6 GPIO_ACTIVE_HIGH>;
|
|
device-wakeup-gpios = <&gpx3 1 GPIO_ACTIVE_HIGH>;
|
|
host-wakeup-gpios = <&gpx2 6 GPIO_ACTIVE_HIGH>;
|
|
clocks = <&max77686 MAX77686_CLK_PMIC>;
|
|
clock-names = "lpo";
|
|
};
|
|
};
|
|
|
|
&serial_2 {
|
|
pinctrl-0 = <&uart_sel>;
|
|
pinctrl-names = "default";
|
|
status = "okay";
|
|
};
|
|
|
|
&tmu {
|
|
status = "okay";
|
|
};
|