256 lines
6.5 KiB
Plaintext
256 lines
6.5 KiB
Plaintext
|
Renesas R-Car sound
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* Modules
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
Renesas R-Car and RZ/G sound is constructed from below modules
|
||
|
|
(for Gen2 or later)
|
||
|
|
|
||
|
|
SCU : Sampling Rate Converter Unit
|
||
|
|
- SRC : Sampling Rate Converter
|
||
|
|
- CMD
|
||
|
|
- CTU : Channel Transfer Unit
|
||
|
|
- MIX : Mixer
|
||
|
|
- DVC : Digital Volume and Mute Function
|
||
|
|
SSIU : Serial Sound Interface Unit
|
||
|
|
SSI : Serial Sound Interface
|
||
|
|
|
||
|
|
See detail of each module's channels, connection, limitation on datasheet
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* Multi channel
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
Multi channel is supported by Multi-SSI, or TDM-SSI.
|
||
|
|
|
||
|
|
Multi-SSI : 6ch case, you can use stereo x 3 SSI
|
||
|
|
TDM-SSI : 6ch case, you can use TDM
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* Enable/Disable each modules
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
See datasheet to check SRC/CTU/MIX/DVC connect-limitation.
|
||
|
|
DT controls enabling/disabling module.
|
||
|
|
${LINUX}/arch/arm/boot/dts/r8a7790-lager.dts can be good example.
|
||
|
|
This is example of
|
||
|
|
|
||
|
|
Playback: [MEM] -> [SRC2] -> [DVC0] -> [SSIU0/SSI0] -> [codec]
|
||
|
|
Capture: [MEM] <- [DVC1] <- [SRC3] <- [SSIU1/SSI1] <- [codec]
|
||
|
|
|
||
|
|
see "Example: simple sound card"
|
||
|
|
|
||
|
|
You can use below.
|
||
|
|
${LINUX}/arch/arm/boot/dts/r8a7790.dts can be good example.
|
||
|
|
|
||
|
|
&src0 &ctu00 &mix0 &dvc0 &ssi0
|
||
|
|
&src1 &ctu01 &mix1 &dvc1 &ssi1
|
||
|
|
&src2 &ctu02 &ssi2
|
||
|
|
&src3 &ctu03 &ssi3
|
||
|
|
&src4 &ssi4
|
||
|
|
&src5 &ctu10 &ssi5
|
||
|
|
&src6 &ctu11 &ssi6
|
||
|
|
&src7 &ctu12 &ssi7
|
||
|
|
&src8 &ctu13 &ssi8
|
||
|
|
&src9 &ssi9
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* SRC (Sampling Rate Converter)
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
[xx]Hz [yy]Hz
|
||
|
|
------> [SRC] ------>
|
||
|
|
|
||
|
|
SRC can convert [xx]Hz to [yy]Hz. Then, it has below 2 modes
|
||
|
|
|
||
|
|
Asynchronous mode: input data / output data are based on different clocks.
|
||
|
|
you can use this mode on Playback / Capture
|
||
|
|
Synchronous mode: input data / output data are based on same clocks.
|
||
|
|
This mode will be used if system doesn't have its input clock,
|
||
|
|
for example digital TV case.
|
||
|
|
you can use this mode on Playback
|
||
|
|
|
||
|
|
------------------
|
||
|
|
** Asynchronous mode
|
||
|
|
------------------
|
||
|
|
|
||
|
|
You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it.
|
||
|
|
see "Example: simple sound card for Asynchronous mode"
|
||
|
|
|
||
|
|
------------------
|
||
|
|
** Synchronous mode
|
||
|
|
------------------
|
||
|
|
|
||
|
|
> amixer set "SRC Out Rate" on
|
||
|
|
> aplay xxxx.wav
|
||
|
|
> amixer set "SRC Out Rate" 48000
|
||
|
|
> amixer set "SRC Out Rate" 44100
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* CTU (Channel Transfer Unit)
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
[xx]ch [yy]ch
|
||
|
|
------> [CTU] -------->
|
||
|
|
|
||
|
|
CTU can convert [xx]ch to [yy]ch, or exchange outputed channel.
|
||
|
|
CTU conversion needs matrix settings.
|
||
|
|
For more detail information, see below
|
||
|
|
|
||
|
|
Renesas R-Car datasheet
|
||
|
|
- Sampling Rate Converter Unit (SCU)
|
||
|
|
- SCU Operation
|
||
|
|
- CMD Block
|
||
|
|
- Functional Blocks in CMD
|
||
|
|
|
||
|
|
Renesas R-Car datasheet
|
||
|
|
- Sampling Rate Converter Unit (SCU)
|
||
|
|
- Register Description
|
||
|
|
- CTUn Scale Value exx Register (CTUn_SVxxR)
|
||
|
|
|
||
|
|
${LINUX}/sound/soc/sh/rcar/ctu.c
|
||
|
|
- comment of header
|
||
|
|
|
||
|
|
You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it.
|
||
|
|
see "Example: simple sound card for channel convert"
|
||
|
|
|
||
|
|
Ex) Exchange output channel
|
||
|
|
Input -> Output
|
||
|
|
1ch -> 0ch
|
||
|
|
0ch -> 1ch
|
||
|
|
|
||
|
|
example of using matrix
|
||
|
|
output 0ch = (input 0ch x 0) + (input 1ch x 1)
|
||
|
|
output 1ch = (input 0ch x 1) + (input 1ch x 0)
|
||
|
|
|
||
|
|
amixer set "CTU Reset" on
|
||
|
|
amixer set "CTU Pass" 9,10
|
||
|
|
amixer set "CTU SV0" 0,4194304
|
||
|
|
amixer set "CTU SV1" 4194304,0
|
||
|
|
|
||
|
|
example of changing connection
|
||
|
|
amixer set "CTU Reset" on
|
||
|
|
amixer set "CTU Pass" 2,1
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* MIX (Mixer)
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
MIX merges 2 sounds path. You can see 2 sound interface on system,
|
||
|
|
and these sounds will be merged by MIX.
|
||
|
|
|
||
|
|
aplay -D plughw:0,0 xxxx.wav &
|
||
|
|
aplay -D plughw:0,1 yyyy.wav
|
||
|
|
|
||
|
|
You need to use "simple-scu-audio-card" or "audio-graph-scu-card" for it.
|
||
|
|
Ex)
|
||
|
|
[MEM] -> [SRC1] -> [CTU02] -+-> [MIX0] -> [DVC0] -> [SSI0]
|
||
|
|
|
|
||
|
|
[MEM] -> [SRC2] -> [CTU03] -+
|
||
|
|
|
||
|
|
see "Example: simple sound card for MIXer"
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* DVC (Digital Volume and Mute Function)
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
DVC controls Playback/Capture volume.
|
||
|
|
|
||
|
|
Playback Volume
|
||
|
|
amixer set "DVC Out" 100%
|
||
|
|
|
||
|
|
Capture Volume
|
||
|
|
amixer set "DVC In" 100%
|
||
|
|
|
||
|
|
Playback Mute
|
||
|
|
amixer set "DVC Out Mute" on
|
||
|
|
|
||
|
|
Capture Mute
|
||
|
|
amixer set "DVC In Mute" on
|
||
|
|
|
||
|
|
Volume Ramp
|
||
|
|
amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
|
||
|
|
amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
|
||
|
|
amixer set "DVC Out Ramp" on
|
||
|
|
aplay xxx.wav &
|
||
|
|
amixer set "DVC Out" 80% // Volume Down
|
||
|
|
amixer set "DVC Out" 100% // Volume Up
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* SSIU (Serial Sound Interface Unit)
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
SSIU can avoid some under/over run error, because it has some buffer.
|
||
|
|
But you can't use it if SSI was PIO mode.
|
||
|
|
In DMA mode, you can select not to use SSIU by using "no-busif" via SSI.
|
||
|
|
|
||
|
|
SSIU handles BUSIF which will be used for TDM Split mode.
|
||
|
|
This driver is assuming that audio-graph card will be used.
|
||
|
|
|
||
|
|
TDM Split mode merges 4 sounds. You can see 4 sound interface on system,
|
||
|
|
and these sounds will be merged SSIU/SSI.
|
||
|
|
|
||
|
|
aplay -D plughw:0,0 xxxx.wav &
|
||
|
|
aplay -D plughw:0,1 xxxx.wav &
|
||
|
|
aplay -D plughw:0,2 xxxx.wav &
|
||
|
|
aplay -D plughw:0,3 xxxx.wav
|
||
|
|
|
||
|
|
2ch 8ch
|
||
|
|
[MEM] -> [SSIU 30] -+-> [SSIU 3] --> [Codec]
|
||
|
|
2ch |
|
||
|
|
[MEM] -> [SSIU 31] -+
|
||
|
|
2ch |
|
||
|
|
[MEM] -> [SSIU 32] -+
|
||
|
|
2ch |
|
||
|
|
[MEM] -> [SSIU 33] -+
|
||
|
|
|
||
|
|
see "Example: simple sound card for TDM Split"
|
||
|
|
|
||
|
|
=============================================
|
||
|
|
* SSI (Serial Sound Interface)
|
||
|
|
=============================================
|
||
|
|
|
||
|
|
** PIO mode
|
||
|
|
|
||
|
|
You can use PIO mode which is for connection check by using.
|
||
|
|
Note: The system will drop non-SSI modules in PIO mode
|
||
|
|
even though if DT is selecting other modules.
|
||
|
|
|
||
|
|
&ssi0 {
|
||
|
|
pio-transfer
|
||
|
|
};
|
||
|
|
|
||
|
|
** DMA mode without SSIU
|
||
|
|
|
||
|
|
You can use DMA without SSIU.
|
||
|
|
Note: under/over run, or noise are likely to occur
|
||
|
|
|
||
|
|
&ssi0 {
|
||
|
|
no-busif;
|
||
|
|
};
|
||
|
|
|
||
|
|
** PIN sharing
|
||
|
|
|
||
|
|
Each SSI can share WS pin. It is based on platform.
|
||
|
|
This is example if SSI1 want to share WS pin with SSI0
|
||
|
|
|
||
|
|
&ssi1 {
|
||
|
|
shared-pin;
|
||
|
|
};
|
||
|
|
|
||
|
|
** Multi-SSI
|
||
|
|
|
||
|
|
You can use Multi-SSI.
|
||
|
|
This is example of SSI0/SSI1/SSI2 (= for 6ch)
|
||
|
|
|
||
|
|
see "Example: simple sound card for Multi channel"
|
||
|
|
|
||
|
|
** TDM-SSI
|
||
|
|
|
||
|
|
You can use TDM with SSI.
|
||
|
|
This is example of TDM 6ch.
|
||
|
|
Driver can automatically switches TDM <-> stereo mode in this case.
|
||
|
|
|
||
|
|
see "Example: simple sound card for TDM"
|