90 lines
2.6 KiB
ReStructuredText
90 lines
2.6 KiB
ReStructuredText
|
Kernel driver thmc50
|
||
|
|
=====================
|
||
|
|
|
||
|
|
Supported chips:
|
||
|
|
|
||
|
|
* Analog Devices ADM1022
|
||
|
|
|
||
|
|
Prefix: 'adm1022'
|
||
|
|
|
||
|
|
Addresses scanned: I2C 0x2c - 0x2e
|
||
|
|
|
||
|
|
Datasheet: http://www.analog.com/en/prod/0,2877,ADM1022,00.html
|
||
|
|
|
||
|
|
* Texas Instruments THMC50
|
||
|
|
|
||
|
|
Prefix: 'thmc50'
|
||
|
|
|
||
|
|
Addresses scanned: I2C 0x2c - 0x2e
|
||
|
|
|
||
|
|
Datasheet: https://www.ti.com/
|
||
|
|
|
||
|
|
|
||
|
|
Author: Krzysztof Helt <krzysztof.h1@wp.pl>
|
||
|
|
|
||
|
|
This driver was derived from the 2.4 kernel thmc50.c source file.
|
||
|
|
|
||
|
|
Credits:
|
||
|
|
|
||
|
|
thmc50.c (2.4 kernel):
|
||
|
|
|
||
|
|
- Frodo Looijaard <frodol@dds.nl>
|
||
|
|
- Philip Edelbrock <phil@netroedge.com>
|
||
|
|
|
||
|
|
Module Parameters
|
||
|
|
-----------------
|
||
|
|
|
||
|
|
* adm1022_temp3: short array
|
||
|
|
List of adapter,address pairs to force chips into ADM1022 mode with
|
||
|
|
second remote temperature. This does not work for original THMC50 chips.
|
||
|
|
|
||
|
|
Description
|
||
|
|
-----------
|
||
|
|
|
||
|
|
The THMC50 implements: an internal temperature sensor, support for an
|
||
|
|
external diode-type temperature sensor (compatible w/ the diode sensor inside
|
||
|
|
many processors), and a controllable fan/analog_out DAC. For the temperature
|
||
|
|
sensors, limits can be set through the appropriate Overtemperature Shutdown
|
||
|
|
register and Hysteresis register. Each value can be set and read to half-degree
|
||
|
|
accuracy. An alarm is issued (usually to a connected LM78) when the
|
||
|
|
temperature gets higher then the Overtemperature Shutdown value; it stays on
|
||
|
|
until the temperature falls below the Hysteresis value. All temperatures are in
|
||
|
|
degrees Celsius, and are guaranteed within a range of -55 to +125 degrees.
|
||
|
|
|
||
|
|
The THMC50 only updates its values each 1.5 seconds; reading it more often
|
||
|
|
will do no harm, but will return 'old' values.
|
||
|
|
|
||
|
|
The THMC50 is usually used in combination with LM78-like chips, to measure
|
||
|
|
the temperature of the processor(s).
|
||
|
|
|
||
|
|
The ADM1022 works the same as THMC50 but it is faster (5 Hz instead of
|
||
|
|
1 Hz for THMC50). It can be also put in a new mode to handle additional
|
||
|
|
remote temperature sensor. The driver use the mode set by BIOS by default.
|
||
|
|
|
||
|
|
In case the BIOS is broken and the mode is set incorrectly, you can force
|
||
|
|
the mode with additional remote temperature with adm1022_temp3 parameter.
|
||
|
|
A typical symptom of wrong setting is a fan forced to full speed.
|
||
|
|
|
||
|
|
Driver Features
|
||
|
|
---------------
|
||
|
|
|
||
|
|
The driver provides up to three temperatures:
|
||
|
|
|
||
|
|
temp1
|
||
|
|
- internal
|
||
|
|
temp2
|
||
|
|
- remote
|
||
|
|
temp3
|
||
|
|
- 2nd remote only for ADM1022
|
||
|
|
|
||
|
|
pwm1
|
||
|
|
- fan speed (0 = stop, 255 = full)
|
||
|
|
pwm1_mode
|
||
|
|
- always 0 (DC mode)
|
||
|
|
|
||
|
|
The value of 0 for pwm1 also forces FAN_OFF signal from the chip,
|
||
|
|
so it stops fans even if the value 0 into the ANALOG_OUT register does not.
|
||
|
|
|
||
|
|
The driver was tested on Compaq AP550 with two ADM1022 chips (one works
|
||
|
|
in the temp3 mode), five temperature readings and two fans.
|