83 lines
2.8 KiB
Plaintext
83 lines
2.8 KiB
Plaintext
|
GPIO-based I2C Arbitration Using a Challenge & Response Mechanism
|
||
|
|
=================================================================
|
||
|
|
This uses GPIO lines and a challenge & response mechanism to arbitrate who is
|
||
|
|
the master of an I2C bus in a multimaster situation.
|
||
|
|
|
||
|
|
In many cases using GPIOs to arbitrate is not needed and a design can use
|
||
|
|
the standard I2C multi-master rules. Using GPIOs is generally useful in
|
||
|
|
the case where there is a device on the bus that has errata and/or bugs
|
||
|
|
that makes standard multimaster mode not feasible.
|
||
|
|
|
||
|
|
Note that this scheme works well enough but has some downsides:
|
||
|
|
* It is nonstandard (not using standard I2C multimaster)
|
||
|
|
* Having two masters on a bus in general makes it relatively hard to debug
|
||
|
|
problems (hard to tell if i2c issues were caused by one master, another, or
|
||
|
|
some device on the bus).
|
||
|
|
|
||
|
|
|
||
|
|
Algorithm:
|
||
|
|
|
||
|
|
All masters on the bus have a 'bus claim' line which is an output that the
|
||
|
|
others can see. These are all active low with pull-ups enabled. We'll
|
||
|
|
describe these lines as:
|
||
|
|
|
||
|
|
- OUR_CLAIM: output from us signaling to other hosts that we want the bus
|
||
|
|
- THEIR_CLAIMS: output from others signaling that they want the bus
|
||
|
|
|
||
|
|
The basic algorithm is to assert your line when you want the bus, then make
|
||
|
|
sure that the other side doesn't want it also. A detailed explanation is best
|
||
|
|
done with an example.
|
||
|
|
|
||
|
|
Let's say we want to claim the bus. We:
|
||
|
|
1. Assert OUR_CLAIM.
|
||
|
|
2. Waits a little bit for the other sides to notice (slew time, say 10
|
||
|
|
microseconds).
|
||
|
|
3. Check THEIR_CLAIMS. If none are asserted then the we have the bus and we are
|
||
|
|
done.
|
||
|
|
4. Otherwise, wait for a few milliseconds and see if THEIR_CLAIMS are released.
|
||
|
|
5. If not, back off, release the claim and wait for a few more milliseconds.
|
||
|
|
6. Go back to 1 (until retry time has expired).
|
||
|
|
|
||
|
|
|
||
|
|
Required properties:
|
||
|
|
- compatible: i2c-arb-gpio-challenge
|
||
|
|
- our-claim-gpio: The GPIO that we use to claim the bus.
|
||
|
|
- their-claim-gpios: The GPIOs that the other sides use to claim the bus.
|
||
|
|
Note that some implementations may only support a single other master.
|
||
|
|
- I2C arbitration bus node. See i2c-arb.txt in this directory.
|
||
|
|
|
||
|
|
Optional properties:
|
||
|
|
- slew-delay-us: microseconds to wait for a GPIO to go high. Default is 10 us.
|
||
|
|
- wait-retry-us: we'll attempt another claim after this many microseconds.
|
||
|
|
Default is 3000 us.
|
||
|
|
- wait-free-us: we'll give up after this many microseconds. Default is 50000 us.
|
||
|
|
|
||
|
|
|
||
|
|
Example:
|
||
|
|
i2c@12ca0000 {
|
||
|
|
compatible = "acme,some-i2c-device";
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
};
|
||
|
|
|
||
|
|
i2c-arbitrator {
|
||
|
|
compatible = "i2c-arb-gpio-challenge";
|
||
|
|
|
||
|
|
i2c-parent = <&{/i2c@12CA0000}>;
|
||
|
|
|
||
|
|
our-claim-gpio = <&gpf0 3 1>;
|
||
|
|
their-claim-gpios = <&gpe0 4 1>;
|
||
|
|
slew-delay-us = <10>;
|
||
|
|
wait-retry-us = <3000>;
|
||
|
|
wait-free-us = <50000>;
|
||
|
|
|
||
|
|
i2c-arb {
|
||
|
|
#address-cells = <1>;
|
||
|
|
#size-cells = <0>;
|
||
|
|
|
||
|
|
i2c@52 {
|
||
|
|
// Normal I2C device
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|