262 lines
8.0 KiB
YAML
262 lines
8.0 KiB
YAML
|
# SPDX-License-Identifier: GPL-2.0-only
|
||
|
|
%YAML 1.2
|
||
|
|
---
|
||
|
|
$id: http://devicetree.org/schemas/soc/qcom/qcom,rpmh-rsc.yaml#
|
||
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||
|
|
|
||
|
|
title: Qualcomm RPMH RSC
|
||
|
|
|
||
|
|
maintainers:
|
||
|
|
- Bjorn Andersson <bjorn.andersson@linaro.org>
|
||
|
|
|
||
|
|
description: |
|
||
|
|
Resource Power Manager Hardened (RPMH) is the mechanism for communicating
|
||
|
|
with the hardened resource accelerators on Qualcomm SoCs. Requests to the
|
||
|
|
resources can be written to the Trigger Command Set (TCS) registers and
|
||
|
|
using a (addr, val) pair and triggered. Messages in the TCS are then sent in
|
||
|
|
sequence over an internal bus.
|
||
|
|
|
||
|
|
The hardware block (Direct Resource Voter or DRV) is a part of the h/w entity
|
||
|
|
(Resource State Coordinator a.k.a RSC) that can handle multiple sleep and
|
||
|
|
active/wake resource requests. Multiple such DRVs can exist in a SoC and can
|
||
|
|
be written to from Linux. The structure of each DRV follows the same template
|
||
|
|
with a few variations that are captured by the properties here.
|
||
|
|
|
||
|
|
A TCS may be triggered from Linux or triggered by the F/W after all the CPUs
|
||
|
|
have powered off to facilitate idle power saving. TCS could be classified as::
|
||
|
|
ACTIVE - Triggered by Linux
|
||
|
|
SLEEP - Triggered by F/W
|
||
|
|
WAKE - Triggered by F/W
|
||
|
|
CONTROL - Triggered by F/W
|
||
|
|
See also:: <dt-bindings/soc/qcom,rpmh-rsc.h>
|
||
|
|
|
||
|
|
The order in which they are described in the DT, should match the hardware
|
||
|
|
configuration.
|
||
|
|
|
||
|
|
Requests can be made for the state of a resource, when the subsystem is
|
||
|
|
active or idle. When all subsystems like Modem, GPU, CPU are idle, the
|
||
|
|
resource state will be an aggregate of the sleep votes from each of those
|
||
|
|
subsystems. Clients may request a sleep value for their shared resources in
|
||
|
|
addition to the active mode requests.
|
||
|
|
|
||
|
|
Drivers that want to use the RSC to communicate with RPMH must specify their
|
||
|
|
bindings as child nodes of the RSC controllers they wish to communicate with.
|
||
|
|
|
||
|
|
properties:
|
||
|
|
compatible:
|
||
|
|
const: qcom,rpmh-rsc
|
||
|
|
|
||
|
|
interrupts:
|
||
|
|
minItems: 1
|
||
|
|
maxItems: 4
|
||
|
|
description:
|
||
|
|
The interrupt that trips when a message complete/response is received for
|
||
|
|
this DRV from the accelerators.
|
||
|
|
Number of interrupts must match number of DRV blocks.
|
||
|
|
|
||
|
|
label:
|
||
|
|
description:
|
||
|
|
Name for the RSC. The name would be used in trace logs.
|
||
|
|
|
||
|
|
qcom,drv-id:
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
description:
|
||
|
|
The ID of the DRV in the RSC block that will be used by this controller.
|
||
|
|
|
||
|
|
qcom,tcs-config:
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32-matrix
|
||
|
|
minItems: 4
|
||
|
|
maxItems: 4
|
||
|
|
items:
|
||
|
|
items:
|
||
|
|
- description: |
|
||
|
|
TCS type::
|
||
|
|
- ACTIVE_TCS
|
||
|
|
- SLEEP_TCS
|
||
|
|
- WAKE_TCS
|
||
|
|
- CONTROL_TCS
|
||
|
|
enum: [ 0, 1, 2, 3 ]
|
||
|
|
- description: Number of TCS
|
||
|
|
description: |
|
||
|
|
The tuple defining the configuration of TCS. Must have two cells which
|
||
|
|
describe each TCS type. The order of the TCS must match the hardware
|
||
|
|
configuration.
|
||
|
|
|
||
|
|
qcom,tcs-offset:
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
description:
|
||
|
|
The offset of the TCS blocks.
|
||
|
|
|
||
|
|
reg:
|
||
|
|
minItems: 1
|
||
|
|
maxItems: 4
|
||
|
|
|
||
|
|
reg-names:
|
||
|
|
minItems: 1
|
||
|
|
items:
|
||
|
|
- const: drv-0
|
||
|
|
- const: drv-1
|
||
|
|
- const: drv-2
|
||
|
|
- const: drv-3
|
||
|
|
|
||
|
|
bcm-voter:
|
||
|
|
$ref: /schemas/interconnect/qcom,bcm-voter.yaml#
|
||
|
|
|
||
|
|
clock-controller:
|
||
|
|
$ref: /schemas/clock/qcom,rpmhcc.yaml#
|
||
|
|
|
||
|
|
power-controller:
|
||
|
|
$ref: /schemas/power/qcom,rpmpd.yaml#
|
||
|
|
|
||
|
|
patternProperties:
|
||
|
|
'-regulators$':
|
||
|
|
$ref: /schemas/regulator/qcom,rpmh-regulator.yaml#
|
||
|
|
|
||
|
|
required:
|
||
|
|
- compatible
|
||
|
|
- interrupts
|
||
|
|
- qcom,drv-id
|
||
|
|
- qcom,tcs-config
|
||
|
|
- qcom,tcs-offset
|
||
|
|
- reg
|
||
|
|
- reg-names
|
||
|
|
|
||
|
|
additionalProperties: false
|
||
|
|
|
||
|
|
examples:
|
||
|
|
- |
|
||
|
|
// For a TCS whose RSC base address is 0x179C0000 and is at a DRV id of
|
||
|
|
// 2, the register offsets for DRV2 start at 0D00, the register
|
||
|
|
// calculations are like this::
|
||
|
|
// DRV0: 0x179C0000
|
||
|
|
// DRV2: 0x179C0000 + 0x10000 = 0x179D0000
|
||
|
|
// DRV2: 0x179C0000 + 0x10000 * 2 = 0x179E0000
|
||
|
|
// TCS-OFFSET: 0xD00
|
||
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||
|
|
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
|
||
|
|
|
||
|
|
rsc@179c0000 {
|
||
|
|
compatible = "qcom,rpmh-rsc";
|
||
|
|
reg = <0x179c0000 0x10000>,
|
||
|
|
<0x179d0000 0x10000>,
|
||
|
|
<0x179e0000 0x10000>;
|
||
|
|
reg-names = "drv-0", "drv-1", "drv-2";
|
||
|
|
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
|
||
|
|
<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
|
||
|
|
<GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
label = "apps_rsc";
|
||
|
|
qcom,tcs-offset = <0xd00>;
|
||
|
|
qcom,drv-id = <2>;
|
||
|
|
qcom,tcs-config = <ACTIVE_TCS 2>,
|
||
|
|
<SLEEP_TCS 3>,
|
||
|
|
<WAKE_TCS 3>,
|
||
|
|
<CONTROL_TCS 1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
- |
|
||
|
|
// For a TCS whose RSC base address is 0xAF20000 and is at DRV id of 0, the
|
||
|
|
// register offsets for DRV0 start at 01C00, the register calculations are
|
||
|
|
// like this::
|
||
|
|
// DRV0: 0xAF20000
|
||
|
|
// TCS-OFFSET: 0x1C00
|
||
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||
|
|
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
|
||
|
|
|
||
|
|
rsc@af20000 {
|
||
|
|
compatible = "qcom,rpmh-rsc";
|
||
|
|
reg = <0xaf20000 0x10000>;
|
||
|
|
reg-names = "drv-0";
|
||
|
|
interrupts = <GIC_SPI 129 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
label = "disp_rsc";
|
||
|
|
qcom,tcs-offset = <0x1c00>;
|
||
|
|
qcom,drv-id = <0>;
|
||
|
|
qcom,tcs-config = <ACTIVE_TCS 0>,
|
||
|
|
<SLEEP_TCS 1>,
|
||
|
|
<WAKE_TCS 1>,
|
||
|
|
<CONTROL_TCS 0>;
|
||
|
|
};
|
||
|
|
|
||
|
|
- |
|
||
|
|
#include <dt-bindings/interrupt-controller/arm-gic.h>
|
||
|
|
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
|
||
|
|
#include <dt-bindings/power/qcom-rpmpd.h>
|
||
|
|
|
||
|
|
rsc@18200000 {
|
||
|
|
compatible = "qcom,rpmh-rsc";
|
||
|
|
reg = <0x18200000 0x10000>,
|
||
|
|
<0x18210000 0x10000>,
|
||
|
|
<0x18220000 0x10000>;
|
||
|
|
reg-names = "drv-0", "drv-1", "drv-2";
|
||
|
|
interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>,
|
||
|
|
<GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>,
|
||
|
|
<GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH>;
|
||
|
|
label = "apps_rsc";
|
||
|
|
qcom,tcs-offset = <0xd00>;
|
||
|
|
qcom,drv-id = <2>;
|
||
|
|
qcom,tcs-config = <ACTIVE_TCS 2>,
|
||
|
|
<SLEEP_TCS 3>,
|
||
|
|
<WAKE_TCS 3>,
|
||
|
|
<CONTROL_TCS 0>;
|
||
|
|
|
||
|
|
clock-controller {
|
||
|
|
compatible = "qcom,sm8350-rpmh-clk";
|
||
|
|
#clock-cells = <1>;
|
||
|
|
clock-names = "xo";
|
||
|
|
clocks = <&xo_board>;
|
||
|
|
};
|
||
|
|
|
||
|
|
power-controller {
|
||
|
|
compatible = "qcom,sm8350-rpmhpd";
|
||
|
|
#power-domain-cells = <1>;
|
||
|
|
operating-points-v2 = <&rpmhpd_opp_table>;
|
||
|
|
|
||
|
|
rpmhpd_opp_table: opp-table {
|
||
|
|
compatible = "operating-points-v2";
|
||
|
|
|
||
|
|
rpmhpd_opp_ret: opp1 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_RETENTION>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_min_svs: opp2 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_MIN_SVS>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_low_svs: opp3 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_svs: opp4 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_SVS>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_svs_l1: opp5 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_SVS_L1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_nom: opp6 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_nom_l1: opp7 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_nom_l2: opp8 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_NOM_L2>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_turbo: opp9 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
|
||
|
|
};
|
||
|
|
|
||
|
|
rpmhpd_opp_turbo_l1: opp10 {
|
||
|
|
opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
bcm-voter {
|
||
|
|
compatible = "qcom,bcm-voter";
|
||
|
|
};
|
||
|
|
};
|