70 lines
1.7 KiB
YAML
70 lines
1.7 KiB
YAML
|
# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
|
||
|
|
%YAML 1.2
|
||
|
|
---
|
||
|
|
$id: http://devicetree.org/schemas/gnss/brcm,bcm4751.yaml#
|
||
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||
|
|
|
||
|
|
title: Broadcom BCM4751 family GNSS Receiver
|
||
|
|
|
||
|
|
maintainers:
|
||
|
|
- Johan Hovold <johan@kernel.org>
|
||
|
|
- Linus Walleij <linus.walleij@linaro.org>
|
||
|
|
|
||
|
|
description:
|
||
|
|
Broadcom GPS chips can be used over the UART or I2C bus. The UART
|
||
|
|
bus requires CTS/RTS support. The number of the capsule is more
|
||
|
|
elaborate than the compatibles BCM4751 may be printed
|
||
|
|
BCM4751IFBG for example.
|
||
|
|
|
||
|
|
allOf:
|
||
|
|
- $ref: gnss-common.yaml#
|
||
|
|
|
||
|
|
properties:
|
||
|
|
compatible:
|
||
|
|
enum:
|
||
|
|
- brcm,bcm4751
|
||
|
|
- brcm,bcm4752
|
||
|
|
- brcm,bcm4753
|
||
|
|
|
||
|
|
reg:
|
||
|
|
description:
|
||
|
|
The I2C Address, not required on UART buses.
|
||
|
|
|
||
|
|
vdd-auxin-supply:
|
||
|
|
description:
|
||
|
|
Main voltage supply, pin name VDD_AUXIN, typically connected
|
||
|
|
directly to a battery such as LiIon 3.8V battery or a 2.6V supply.
|
||
|
|
|
||
|
|
vddio-supply:
|
||
|
|
description:
|
||
|
|
IO voltage supply, pin name VDDIO, typically 1.8V
|
||
|
|
|
||
|
|
reset-gpios:
|
||
|
|
maxItems: 1
|
||
|
|
description: An optional active low reset line, should be flagged with
|
||
|
|
GPIO_ACTIVE_LOW.
|
||
|
|
|
||
|
|
enable-gpios:
|
||
|
|
description: Enable GPIO line, connected to pins named REGPU or NSTANDBY.
|
||
|
|
If the line is active low such as NSTANDBY, it should be tagged
|
||
|
|
GPIO_ACTIVE_LOW.
|
||
|
|
|
||
|
|
required:
|
||
|
|
- compatible
|
||
|
|
- enable-gpios
|
||
|
|
|
||
|
|
unevaluatedProperties: false
|
||
|
|
|
||
|
|
examples:
|
||
|
|
- |
|
||
|
|
#include <dt-bindings/gpio/gpio.h>
|
||
|
|
serial {
|
||
|
|
gnss {
|
||
|
|
compatible = "brcm,bcm4751";
|
||
|
|
vdd-auxin-supply = <&vbat>;
|
||
|
|
reset-gpios = <&gpio0 15 GPIO_ACTIVE_LOW>;
|
||
|
|
enable-gpios = <&gpio0 16 GPIO_ACTIVE_HIGH>;
|
||
|
|
current-speed = <38400>;
|
||
|
|
};
|
||
|
|
};
|