109 lines
1.9 KiB
Plaintext
109 lines
1.9 KiB
Plaintext
|
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||
|
|
/*
|
||
|
|
* Copyright 2022 Toradex
|
||
|
|
*/
|
||
|
|
|
||
|
|
/* Colibri AD0 to AD3 */
|
||
|
|
&adc1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/*
|
||
|
|
* The Atmel maxtouch controller uses SODIMM 28/30, also used for PWM<B>, PWM<C>, aka pwm2, pwm3.
|
||
|
|
* So if you enable following capacitive touch controller, disable pwm2/pwm3 first.
|
||
|
|
*/
|
||
|
|
&atmel_mxt_ts {
|
||
|
|
interrupt-parent = <&gpio1>;
|
||
|
|
interrupts = <9 IRQ_TYPE_EDGE_FALLING>; /* SODIMM 28 / INT */
|
||
|
|
pinctrl-0 = <&pinctrl_atmel_adapter>;
|
||
|
|
reset-gpios = <&gpio1 10 GPIO_ACTIVE_LOW>; /* SODIMM 30 / RST */
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri SSP */
|
||
|
|
&ecspi3 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri Fast Ethernet */
|
||
|
|
&fec1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&gpio2 {
|
||
|
|
/*
|
||
|
|
* uart25 turns the UART transceiver for UART2 and 5 on. If one wants to turn the
|
||
|
|
* transceiver off, that property has to be deleted and the gpio handled in userspace.
|
||
|
|
* The same applies to uart1_tx_on where the UART1 transceiver is turned on.
|
||
|
|
*/
|
||
|
|
uart25-tx-on-hog {
|
||
|
|
gpio-hog;
|
||
|
|
gpios = <27 GPIO_ACTIVE_HIGH>; /* SODIMM 104 */
|
||
|
|
output-high;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&gpio5 {
|
||
|
|
uart1-tx-on-hog {
|
||
|
|
gpio-hog;
|
||
|
|
gpios = <17 GPIO_ACTIVE_HIGH>; /* SODIMM 102 */
|
||
|
|
output-high;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri I2C: I2C3_SDA/SCL on SODIMM 194/196 */
|
||
|
|
&i2c4 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri PWM<A> */
|
||
|
|
&pwm1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri PWM<B> */
|
||
|
|
&pwm2 {
|
||
|
|
/* The pwm2 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri PWM<C> */
|
||
|
|
&pwm3 {
|
||
|
|
/* The pwm3 should be disabled to enable atmel_mxt_ts touchscreen for adapter. */
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri PWM<D> */
|
||
|
|
&pwm4 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* M41T0M6 real time clock */
|
||
|
|
&rtc {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri UART_A */
|
||
|
|
&uart1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri UART_B */
|
||
|
|
&uart2 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri UART_C */
|
||
|
|
&uart3 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri USBC */
|
||
|
|
&usbotg1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
/* Colibri MMC/SD */
|
||
|
|
&usdhc1 {
|
||
|
|
status = "okay";
|
||
|
|
};
|