114 lines
2.1 KiB
Plaintext
114 lines
2.1 KiB
Plaintext
|
// SPDX-License-Identifier: GPL-2.0
|
||
|
|
/dts-v1/;
|
||
|
|
#include "bcm2711.dtsi"
|
||
|
|
#include "bcm2711-rpi.dtsi"
|
||
|
|
#include "bcm283x-rpi-wifi-bt.dtsi"
|
||
|
|
|
||
|
|
/ {
|
||
|
|
compatible = "raspberrypi,4-compute-module", "brcm,bcm2711";
|
||
|
|
|
||
|
|
chosen {
|
||
|
|
/* 8250 auxiliary UART instead of pl011 */
|
||
|
|
stdout-path = "serial1:115200n8";
|
||
|
|
};
|
||
|
|
|
||
|
|
sd_io_1v8_reg: sd_io_1v8_reg {
|
||
|
|
compatible = "regulator-gpio";
|
||
|
|
regulator-name = "vdd-sd-io";
|
||
|
|
regulator-min-microvolt = <1800000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
regulator-always-on;
|
||
|
|
regulator-settling-time-us = <5000>;
|
||
|
|
gpios = <&expgpio 4 GPIO_ACTIVE_HIGH>;
|
||
|
|
states = <1800000 0x1>,
|
||
|
|
<3300000 0x0>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
sd_vcc_reg: sd_vcc_reg {
|
||
|
|
compatible = "regulator-fixed";
|
||
|
|
regulator-name = "vcc-sd";
|
||
|
|
regulator-min-microvolt = <3300000>;
|
||
|
|
regulator-max-microvolt = <3300000>;
|
||
|
|
regulator-boot-on;
|
||
|
|
enable-active-high;
|
||
|
|
gpio = <&expgpio 6 GPIO_ACTIVE_HIGH>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&bt {
|
||
|
|
shutdown-gpios = <&expgpio 0 GPIO_ACTIVE_HIGH>;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* EMMC2 is used to drive the eMMC */
|
||
|
|
&emmc2 {
|
||
|
|
bus-width = <8>;
|
||
|
|
vqmmc-supply = <&sd_io_1v8_reg>;
|
||
|
|
vmmc-supply = <&sd_vcc_reg>;
|
||
|
|
broken-cd;
|
||
|
|
/* Even the IP block is limited to 100 MHz
|
||
|
|
* this provides a throughput gain
|
||
|
|
*/
|
||
|
|
mmc-hs200-1_8v;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&expgpio {
|
||
|
|
gpio-line-names = "BT_ON",
|
||
|
|
"WL_ON",
|
||
|
|
"PWR_LED_OFF",
|
||
|
|
"ANT1",
|
||
|
|
"VDD_SD_IO_SEL",
|
||
|
|
"CAM_GPIO",
|
||
|
|
"SD_PWR_ON",
|
||
|
|
"ANT2";
|
||
|
|
|
||
|
|
ant1: ant1-hog {
|
||
|
|
gpio-hog;
|
||
|
|
gpios = <3 GPIO_ACTIVE_HIGH>;
|
||
|
|
/* internal antenna enabled */
|
||
|
|
output-high;
|
||
|
|
line-name = "ant1";
|
||
|
|
};
|
||
|
|
|
||
|
|
ant2: ant2-hog {
|
||
|
|
gpio-hog;
|
||
|
|
gpios = <7 GPIO_ACTIVE_HIGH>;
|
||
|
|
/* external antenna disabled */
|
||
|
|
output-low;
|
||
|
|
line-name = "ant2";
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
&genet {
|
||
|
|
phy-handle = <&phy1>;
|
||
|
|
phy-mode = "rgmii-rxid";
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&genet_mdio {
|
||
|
|
phy1: ethernet-phy@0 {
|
||
|
|
/* No PHY interrupt */
|
||
|
|
reg = <0x0>;
|
||
|
|
};
|
||
|
|
};
|
||
|
|
|
||
|
|
/* uart0 communicates with the BT module */
|
||
|
|
&uart0 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&uart0_ctsrts_gpio30 &uart0_gpio32>;
|
||
|
|
uart-has-rtscts;
|
||
|
|
};
|
||
|
|
|
||
|
|
/* uart1 is mapped to the pin header */
|
||
|
|
&uart1 {
|
||
|
|
pinctrl-names = "default";
|
||
|
|
pinctrl-0 = <&uart1_gpio14>;
|
||
|
|
status = "okay";
|
||
|
|
};
|
||
|
|
|
||
|
|
&wifi_pwrseq {
|
||
|
|
reset-gpios = <&expgpio 1 GPIO_ACTIVE_LOW>;
|
||
|
|
};
|