160 lines
6.0 KiB
YAML
160 lines
6.0 KiB
YAML
|
# SPDX-License-Identifier: GPL-2.0
|
||
|
|
%YAML 1.2
|
||
|
|
---
|
||
|
|
$id: http://devicetree.org/schemas/display/panel/panel-common.yaml#
|
||
|
|
$schema: http://devicetree.org/meta-schemas/core.yaml#
|
||
|
|
|
||
|
|
title: Common Properties for Display Panels
|
||
|
|
|
||
|
|
maintainers:
|
||
|
|
- Thierry Reding <thierry.reding@gmail.com>
|
||
|
|
- Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
||
|
|
|
||
|
|
description: |
|
||
|
|
This document defines device tree properties common to several classes of
|
||
|
|
display panels. It doesn't constitue a device tree binding specification by
|
||
|
|
itself but is meant to be referenced by device tree bindings.
|
||
|
|
|
||
|
|
When referenced from panel device tree bindings the properties defined in this
|
||
|
|
document are defined as follows. The panel device tree bindings are
|
||
|
|
responsible for defining whether each property is required or optional.
|
||
|
|
|
||
|
|
properties:
|
||
|
|
# Descriptive Properties
|
||
|
|
width-mm:
|
||
|
|
description:
|
||
|
|
Specifies the width of the physical area where images are displayed. This
|
||
|
|
property is expressed in millimeters and rounded to the closest unit.
|
||
|
|
|
||
|
|
height-mm:
|
||
|
|
description:
|
||
|
|
Specifies the height of the physical area where images are displayed. This
|
||
|
|
property is expressed in millimeters and rounded to the closest unit.
|
||
|
|
|
||
|
|
label:
|
||
|
|
description: |
|
||
|
|
The label property specifies a symbolic name for the panel as a
|
||
|
|
string suitable for use by humans. It typically contains a name inscribed
|
||
|
|
on the system (e.g. as an affixed label) or specified in the system's
|
||
|
|
documentation (e.g. in the user's manual).
|
||
|
|
|
||
|
|
If no such name exists, and unless the property is mandatory according to
|
||
|
|
device tree bindings, it shall rather be omitted than constructed of
|
||
|
|
non-descriptive information. For instance an LCD panel in a system that
|
||
|
|
contains a single panel shall not be labelled "LCD" if that name is not
|
||
|
|
inscribed on the system or used in a descriptive fashion in system
|
||
|
|
documentation.
|
||
|
|
|
||
|
|
rotation:
|
||
|
|
description:
|
||
|
|
Display rotation in degrees counter clockwise (0,90,180,270)
|
||
|
|
$ref: /schemas/types.yaml#/definitions/uint32
|
||
|
|
enum: [0, 90, 180, 270]
|
||
|
|
|
||
|
|
# Display Timings
|
||
|
|
panel-timing:
|
||
|
|
description:
|
||
|
|
Most display panels are restricted to a single resolution and
|
||
|
|
require specific display timings. The panel-timing subnode expresses those
|
||
|
|
timings.
|
||
|
|
$ref: panel-timing.yaml#
|
||
|
|
|
||
|
|
display-timings:
|
||
|
|
description:
|
||
|
|
Some display panels support several resolutions with different timings.
|
||
|
|
The display-timings bindings supports specifying several timings and
|
||
|
|
optionally specifying which is the native mode.
|
||
|
|
$ref: display-timings.yaml#
|
||
|
|
|
||
|
|
# Connectivity
|
||
|
|
port:
|
||
|
|
$ref: /schemas/graph.yaml#/properties/port
|
||
|
|
|
||
|
|
ddc-i2c-bus:
|
||
|
|
$ref: /schemas/types.yaml#/definitions/phandle
|
||
|
|
description:
|
||
|
|
Some panels expose EDID information through an I2C-compatible
|
||
|
|
bus such as DDC2 or E-DDC. For such panels the ddc-i2c-bus contains a
|
||
|
|
phandle to the system I2C controller connected to that bus.
|
||
|
|
|
||
|
|
no-hpd:
|
||
|
|
type: boolean
|
||
|
|
description:
|
||
|
|
This panel is supposed to communicate that it's ready via HPD
|
||
|
|
(hot plug detect) signal, but the signal isn't hooked up so we should
|
||
|
|
hardcode the max delay from the panel spec when powering up the panel.
|
||
|
|
|
||
|
|
hpd-gpios:
|
||
|
|
maxItems: 1
|
||
|
|
description:
|
||
|
|
If Hot Plug Detect (HPD) is connected to a GPIO in the system rather
|
||
|
|
than a dedicated HPD pin the pin can be specified here.
|
||
|
|
|
||
|
|
# Control I/Os
|
||
|
|
|
||
|
|
# Many display panels can be controlled through pins driven by GPIOs. The nature
|
||
|
|
# and timing of those control signals are device-specific and left for panel
|
||
|
|
# device tree bindings to specify. The following GPIO specifiers can however be
|
||
|
|
# used for panels that implement compatible control signals.
|
||
|
|
|
||
|
|
enable-gpios:
|
||
|
|
maxItems: 1
|
||
|
|
description: |
|
||
|
|
Specifier for a GPIO connected to the panel enable control signal. The
|
||
|
|
enable signal is active high and enables operation of the panel. This
|
||
|
|
property can also be used for panels implementing an active low power down
|
||
|
|
signal, which is a negated version of the enable signal. Active low enable
|
||
|
|
signals (or active high power down signals) can be supported by inverting
|
||
|
|
the GPIO specifier polarity flag.
|
||
|
|
|
||
|
|
Note that the enable signal control panel operation only and must not be
|
||
|
|
confused with a backlight enable signal.
|
||
|
|
|
||
|
|
reset-gpios:
|
||
|
|
maxItems: 1
|
||
|
|
description:
|
||
|
|
Specifier for a GPIO connected to the panel reset control signal.
|
||
|
|
The reset signal is active low and resets the panel internal logic
|
||
|
|
while active. Active high reset signals can be supported by inverting the
|
||
|
|
GPIO specifier polarity flag.
|
||
|
|
|
||
|
|
te-gpios:
|
||
|
|
maxItems: 1
|
||
|
|
description:
|
||
|
|
GPIO spec for the tearing effect synchronization signal.
|
||
|
|
The tearing effect signal is active high. Active low signals can be
|
||
|
|
supported by inverting the GPIO specifier polarity flag.
|
||
|
|
|
||
|
|
# Power
|
||
|
|
power-supply:
|
||
|
|
description:
|
||
|
|
Display panels require power to be supplied. While several panels need
|
||
|
|
more than one power supply with panel-specific constraints governing the
|
||
|
|
order and timings of the power supplies, in many cases a single power
|
||
|
|
supply is sufficient, either because the panel has a single power rail, or
|
||
|
|
because all its power rails can be driven by the same supply. In that case
|
||
|
|
the power-supply property specifies the supply powering the panel as a
|
||
|
|
phandle to a regulator.
|
||
|
|
|
||
|
|
# Backlight
|
||
|
|
|
||
|
|
# Most display panels include a backlight. Some of them also include a backlight
|
||
|
|
# controller exposed through a control bus such as I2C or DSI. Others expose
|
||
|
|
# backlight control through GPIO, PWM or other signals connected to an external
|
||
|
|
# backlight controller.
|
||
|
|
|
||
|
|
backlight:
|
||
|
|
$ref: /schemas/types.yaml#/definitions/phandle
|
||
|
|
description:
|
||
|
|
For panels whose backlight is controlled by an external backlight
|
||
|
|
controller, this property contains a phandle that references the
|
||
|
|
controller.
|
||
|
|
|
||
|
|
dependencies:
|
||
|
|
width-mm: [ height-mm ]
|
||
|
|
height-mm: [ width-mm ]
|
||
|
|
|
||
|
|
additionalProperties: true
|
||
|
|
|
||
|
|
...
|